Efficient Networks 5200 Series, 5500 Series, 5400 Series manual Access Concentrator, Service Name

Page 26

SpeedStream Router User Guide

2.In the PPP Login screen, enter the user name and password.

3.To save the settings, select Save Settings on Connect.

4.To configure additional PPP options, click Show Options.

The input box expands to display the PPP Options section.

5.Enter the desired PPP options:

•Access Concentrator:

Enter the [optional] name of the access concentrator as provided by your ISP.

•Service Name:

Enter the [optional] service name provided by your ISP.

•Auto-Connect on Disconnect: If selected, router will attempt to login every time the DSL trains if you selected Save Settings on Connect.

•Idle Timeout (with time value): Select to disconnect the PPP session if the router has had no traffic for the specified amount of time. Enter the time in minutes. This cannot be used with Autoconnect.

PPPoffers the Connect on Demand feature whereby the router will attempt to log on to a disconnected PPP session if there is requested traffic from the LAN side, and if there is a saved user name and password. This is especially useful with the Idle Timeout feature. Connect on Demand is non- configurable, but is always enabled.

18

Image 26

Contents Router User Guide Software License General Provisions Contents Viewing Status Screens Iii List of Illustrations 51-57SpeedStream Router User Guide Introduction Hardware DescriptionFeatures and Benefits About the SpeedStream RouterSession Tracking General Safety GuidelinesFirewall Security Basic Installation Procedure Installing the RouterHardware Installation Minimum System RequirementsIn-Line Filter Installing Line FiltersRecording System Settings Two-to-One Adapter Connecting the CablesWall-Mount Filter Ethernet Installation Method USB Installation Method TCP/IP Properties dialog box displays Configuring Computer Network SettingsWindows 95 / 98 / ME TCP/IP Properties dialog box, click the IP Address tab Windows NT Windows Double-clickNetwork and Dial-up ConnectionsWindows XP Level Getting StartedNavigating the Web Interface SnoozeLog Screen Navigation ElementsIP Filter Rules Logging On to the Web Interface To log on to the Web interface for the first timeEntering the Network Password Logging On to a PPP SessionAccess Concentrator Service NameClick Save Settings Customizing Router SettingsTo specify the host configuration settings HostDhcp Configuration Options To specify the Dhcp configuration settings User Setup System Login To change the user name or passwordTime Client Time Client Configuration OptionsTo configure the Time Client Static RoutesTo enable NAT and specify a destination IP address To access the NAT/NAPT Configuration screenTo disable NAT and Napt NAT/NAPT ServerPort Forwarding Port Forwarding Configuration OptionsTo enable Napt To delete all entries in the table To edit an existing port forwarding configurationTo delete an existing entry To add a port forwarding entryFirewall Firewall Security LevelsFirewall Snooze Control DMZ SettingsDMZ Configuration Options To enable DMZ and specify an accessible computer Custom IP Filter Rules To disable DMZOn the Firewall DMZ Configuration screen, click Disable DMZ Cloning a Rule DefinitionCreating Custom IP Filter Rules Firewall Simple Setup screenCustom IP Filter Configuration Fill in the following informationSpecify Source Port Operator options Select a protocol to filterIf TCP/UDP chosen in , select the desired rule options Specify Destination Port Operator optionsBackground Types of AttackADS Configuration Options To save the new settings To enable ADSSelect Enable Attack Detection To filter, or drop, a packet typeRFC2684 RFC2684 Configuration OptionsTo configure RFC2684 settings To configure UPnP settings Bridge ModeUPnP Configuration Options UPnP Universal Plug and PlayRIP Routing Information Protocol RIP Configuration OptionsTo enable bridge mode System Log To configure RIP settingsLAN Servers To configure the System Log RebootSystem Log Configuration Options To reset the router ResetFirmware Update To update the router firmwareClick Run Diagnostics at the bottom of the screen DiagnosticsTo cancel the reset Viewing Status Screens System SummaryTo display the Interface Map Interface MapFirewall Log Interface Map Interface Map screen displaysATM/AAL Status/Statistics To update the displayStatus and Statistics Screens To display the System Log screenDSL Status/Statistics Ethernet Status/StatisticsUSB Status/Statistics RoutesInterpreting the LED Display TroubleshootingBasic Troubleshooting Steps Resolving Specific Issues Pwr LED Not LitContacting Technical Support Attack Detection System Configuration Data SheetsAdministrative User Setup Firewall Custom IP Filter Configuration Firewall DMZ Firewall Level Firewall Snooze ControlPPP Login RIP Static RouteUPnP Technical Specifications Firewall Security Levels ProtocolNeed for Speed VNC Acronyms and Technical Concepts AcronymsOctet Rx ErrorsMAC address PPPoETechnical Concepts Dhcp Dynamic Host Configuration Protocol Icsa 3.0a-compliancy PPP Point-to-Point Protocol Index Data Sheets See Configuration Data Sheets PPP Network TCP