Efficient Networks 5500 Series, 5400 Series, 5200 Series manual Ppp

Page 78

SpeedStream Router User Guide

Security Levels	27-28, 54, 59-61
Snooze Control configuration		28, 43, 54
Status screens		43, 43-44
Firmware update		41-42
Flags		34
Flash memory		41
Fraggle Attack (ADS)		34
Fragmented
ICMP header (ADS)		35
TCP header (ADS)		35
TCP packet (ADS)		35
UDP header (ADS)		35
G
Globally enable ADS		35
Glossary		62-66
GRE (Port Forwarding)		26
H
Hard disk space		4
Hardware installation		4
Headers		33
High firewall security level		27
Host configuration	19, 29, 50, 54
I
ICSA 3.0a-compliant (firewall security level)	......................	27
ICMP header		35
Idle timeout (PPP login)		18
IEEE 802.1.d Transparent Learning Bridges		58
IGD		37
In-line filter		5
Inbound		31
Infinite time		21
Informative events (syslog)		40
Installation procedures		4
Installing
Line filters		5
Network interface card		7
Interface Map		44
Internet address for Technical Support		49
Internet Gateway Device See IGD
Invalid IP packet fragment (ADS)		35
IP Addresses
Commonly used non-Internet routed IP ranges		20
Custom Firewall IP Filter Rules	30-32, 64-65
Destination address (NAT)		24
DHCP Address Restrictions		19
DMZ configuration		29

DNS	20
Fragments	35
Header	33
LAN IP Configuration Data Sheet	54
NAT-enabled internal LAN address	24
Netmask	20
Netmask (RFC2684)	36
Packet filtering	3
Primary/secondary (Time Client)	23
Redirected addresses (port forwarding)	25-26
Restrictions	19
RFC2468 configuration	36
Router default	9
Start/End ranges for DHCP	20-21
Static (Host Settings)	19
IPSec	33
IPv4	33
K
Keep stateless	31
L
LAN IP	54
LAN servers	39
LAN source address on WAN (ADS)	34
Land attack	34
Lease time	21-22
LED display panel	1
dsl	47-48
enet	47-48
pwr	47-48
usb	47-48
LLC encapsulation	67
Logging
On to PPP session	17
On to Web interface	16
Packet types to the firewall event log	35
Login
Menu option	14
Password error	48
PPP	18, 55-56
Security levels	16, 22
Low firewall security level	27
M
MAC address	29, 43
Major events (System Log)	40
Malformed packets	32
Management specifications	58

70

Image 78

Contents Router User Guide Software License General Provisions Contents Viewing Status Screens Iii List of Illustrations 51-57SpeedStream Router User Guide Introduction Hardware DescriptionFeatures and Benefits About the SpeedStream RouterGeneral Safety Guidelines Firewall SecuritySession Tracking Basic Installation Procedure Installing the RouterHardware Installation Minimum System RequirementsInstalling Line Filters Recording System SettingsIn-Line Filter Connecting the Cables Wall-Mount FilterTwo-to-One Adapter Ethernet Installation Method USB Installation Method Configuring Computer Network Settings Windows 95 / 98 / METCP/IP Properties dialog box displays TCP/IP Properties dialog box, click the IP Address tab Windows NT Windows Double-clickNetwork and Dial-up ConnectionsWindows XP Level Getting StartedNavigating the Web Interface SnoozeScreen Navigation Elements IP Filter RulesLog Logging On to the Web Interface To log on to the Web interface for the first timeEntering the Network Password Logging On to a PPP SessionAccess Concentrator Service NameClick Save Settings Customizing Router SettingsTo specify the host configuration settings HostDhcp Configuration Options To specify the Dhcp configuration settings User Setup System Login To change the user name or passwordTime Client Time Client Configuration OptionsTo configure the Time Client Static RoutesTo enable NAT and specify a destination IP address To access the NAT/NAPT Configuration screenTo disable NAT and Napt NAT/NAPT ServerPort Forwarding Configuration Options To enable NaptPort Forwarding To delete all entries in the table To edit an existing port forwarding configurationTo delete an existing entry To add a port forwarding entryFirewall Firewall Security LevelsDMZ Settings DMZ Configuration OptionsFirewall Snooze Control To enable DMZ and specify an accessible computer Custom IP Filter Rules To disable DMZOn the Firewall DMZ Configuration screen, click Disable DMZ Cloning a Rule DefinitionCreating Custom IP Filter Rules Firewall Simple Setup screenCustom IP Filter Configuration Fill in the following informationSpecify Source Port Operator options Select a protocol to filterIf TCP/UDP chosen in , select the desired rule options Specify Destination Port Operator optionsBackground Types of AttackADS Configuration Options To save the new settings To enable ADSSelect Enable Attack Detection To filter, or drop, a packet typeRFC2684 Configuration Options To configure RFC2684 settingsRFC2684 To configure UPnP settings Bridge ModeUPnP Configuration Options UPnP Universal Plug and PlayRIP Configuration Options To enable bridge modeRIP Routing Information Protocol To configure RIP settings LAN ServersSystem Log Reboot System Log Configuration OptionsTo configure the System Log To reset the router ResetFirmware Update To update the router firmwareDiagnostics To cancel the resetClick Run Diagnostics at the bottom of the screen Viewing Status Screens System SummaryTo display the Interface Map Interface MapFirewall Log Interface Map Interface Map screen displaysATM/AAL Status/Statistics To update the displayStatus and Statistics Screens To display the System Log screenDSL Status/Statistics Ethernet Status/StatisticsUSB Status/Statistics RoutesTroubleshooting Basic Troubleshooting StepsInterpreting the LED Display Resolving Specific Issues Pwr LED Not LitContacting Technical Support Configuration Data Sheets Administrative User SetupAttack Detection System Firewall Custom IP Filter Configuration Firewall DMZ Firewall Level Firewall Snooze ControlPPP Login RIP Static RouteUPnP Technical Specifications Firewall Security Levels ProtocolNeed for Speed VNC Acronyms and Technical Concepts AcronymsOctet Rx ErrorsMAC address PPPoETechnical Concepts Dhcp Dynamic Host Configuration Protocol Icsa 3.0a-compliancy PPP Point-to-Point Protocol Index Data Sheets See Configuration Data Sheets PPP Network TCP