Dell 610 technical specifications ALERT! Cover was previously removed

Page 81

surface, such as a foam pad, that will sufficiently cushion it.

Configure the device for a SCSI ID number and disable termination, if necessary. For instructions, see the documentation that came with the SCSI device as well as "SCSI Configuration Guidelines" found earlier in this section.

3. Install the SCSI devices as appropriate.

To install a SCSI hard-disk drive, complete steps 3 through 9 of "Installing an EIDE Hard-Disk Drive in the Internal Hard-Disk Drive Cage" found earlier in this chapter. Then continue with step 4 of this procedure.

To install a SCSI tape drive, CD-ROM drive, or DAT drive, complete steps 2 through 6 of "Installing a Drive in a

5.25-Inch Drive Bay" found earlier in this chapter. Then continue with step 4 of this procedure. To install an external SCSI device, continue with step 4 of this procedure.

If you are installing a SCSI host adapter card, configure the card and install it in an empty expansion slot (see "Installing an Expansion Card".) If you attach any SCSI hard-disk drives to the host adapter card, connect the hard- disk drive access cable to the SCSI host adapter card and to the AUX LED connector on the system board (see Figure 9-1).

4.Attach the SCSI cable to each SCSI device.

For additional instructions on connecting SCSI devices, see "SCSI Cables" found earlier in this section.

If you are installing an internal SCSI device, firmly press the SCSI cable's header connector onto the 50- or 68-pin connector on the back of the device.

CAUTION: You must match the colored strip on the cable with pin 1 on the drive's interface connector to avoid possible damage to your system.

The connectors on Narrow SCSI cables are keyed for proper positioning - a raised area on the outside of the header connector fits into a notch on the device connector. The connectors on Wide SCSI cables are shaped so that they can be attached one way only.

If you are installing an external SCSI device, connect one end of the external SCSI cable to the SCSI bus connector on the back of the device. Attach the other end of the external SCSI cable to the SCSI connector on the system back panel.

NOTE: Dell offers an external SCSI 68-pin-to-50-pin adapter kit for connecting SCSI-3 devices to the SCSI-2 connector on the Precision 610 system back panel. Contact your Dell sales representative for more information.

5. Connect the SCSI device(s) to power.

If you are installing an internal SCSI device, connect a DC power cable to the power input connector on the SCSI device.

If you are installing an external SCSI device, connect the socket end of the power cable into the AC power receptacle on the back of the SCSI device. Connect the other end of the power cable into a standard electrical wall outlet.

Check all other cable connections. Fold all internal cables out of the way to provide airflow for the fan or cooling vents.

6.If you installed an externally accessible device, remove the front bezel and remove the front-panel insert for the drive bay from the front bezel. Then replace the front bezel.

For instructions, see "Removing and Replacing the Front Bezel" and "Removing and Replacing Front-Panel Inserts".

7.Replace the computer cover. Then reconnect your computer and peripherals to their power sources, and turn them on.

NOTE: After you remove and replace the cover, the chassis intrusion detector will cause the following message to be displayed at the next system start-up:

ALERT! Cover was previously removed.

8.To reset the chassis intrusion detector, enter the System Setup program and reset Chassis Intrusion to Not Detected. See "Using the System Setup Program" for instructions.

NOTE: If a setup password has been assigned by someone else, contact your network administrator for information on resetting the chassis intrusion detector.

9. If necessary, update the drive system configuration information in the System Setup program.

Page 80 Page 82
Image 81
Page 80 Page 82
Contents Initial release 19 May When Using Your Computer System When Working Inside Your Computer Protecting Against Electrostatic Discharge Overview System FeaturesPage Page Important Note to Windows NT 4.0 Users Reinstalling Windows NTFront Panel Back PanelCreating Disk Partitions for Windows NT Connecting External Devices Getting HelpSecurity Cable Slot and Padlock Ring Dell-Installed Software Support Utilities Backing Up the Software Support UtilitiesSoftware Support Utilities on Diskette System Utilities and Services Removing a ServiceAsset Tag Utility Assigning and Deleting an Asset Tag Number Dell AutoShutdown ServiceAsset 1234$ABCD Assigning and Deleting an Owner TagDell ThermalShutdown Service Auto Power On UtilityInstalling the Auto Power On Utility Removing the Windows NT 4.0 Microsoft Updated Atapi Driver Microsoft Updated Atapi DriversSystem Setup Screen Entering the System Setup ProgramSystem-Setup Navigation Keys Keys Action Using the System Setup ProgramSystem Time System Setup OptionsDiskette Drive a and Diskette Drive B System DatePrimary Drive and Secondary Drive Eide DevicesIf You Have a Problem Boot SequenceHard-Disk Drive Sequence If You Know the Drive-Type NumberReserved Memory System MemoryCPU Speed PXECPU IDs Integrated DevicesNIC IDE Drive Interface Parallel Port ModeDiskette Interface PC SpeakerPassword Status System PasswordSetup Password System SecurityAuto Power On Report Keyboard ErrorsKeyboard NumLock Wakeup On LANPower Management Saving Monitor PowerSaving Eide Hard-Disk Drive Power Thermal Power-Off Asset TagSystem Data Options Assigning a System Password Using the System Password FeatureDeleting or Changing an Existing System Password Type the password and press EnterUsing the Setup Password Feature Assigning a Setup PasswordOperating With a Setup Password Enabled Deleting or Changing an Existing Setup Password Disabling a Forgotten PasswordInformation on resetting the chassis intrusion detector Responding to Error MessagesQuick Start When to Run the ICU About the ICUICU Database Preparing to Use the ICU Accessing HelpStarting the ICU Backing Up the ICU DisketteKeyss Action Adding a Listed CardCard Configuration Dialog Box Adding an Unlisted Card Available Settings List BoxSpecify Interrupt Dialog Box Specify I/O Port Dialog Box Modifying a CardRemoving a Card Viewing Resources Saving the System ConfigurationExiting the ICU Locking and Unlocking CardsLocking and Unlocking All Resources Locking and Unlocking Configuration ResourcesPage NIC Connector and Indicators Connecting to a NetworkConfiguring the NIC Network Cable RequirementsWindows NT 4.0 NIC Driver Setting the Network Frame Type Manually Configuring a 3Com PCI 3C905b NICReinstallation Speakers Connecting Audio DevicesAdjusting Volume in Windows NT Adjusting VolumeMicrophones Record/Playback DevicesUsing Audio Utilities Adjusting 3D SoundInstalling Audio Drivers Muting the Internal SpeakerScsi Device Considerations Scsi Drivers for Windows NT Installing Scsi DriversPage Safety First-For You and Your Computer Before You BeginUnpacking Your Hardware Option Replacing the Computer Cover Removing the Computer CoverReplacing the Computer Cover Inside Your ComputerRotating the Power Supply Rotating the Power Supply Away From the System BoardExpansion Cards System Board FeaturesExpansion Slots Installing an Expansion CardRemoving the Filler Bracket Removing an Expansion CardAdding Memory Dimm Installation GuidelinesTotal Dimm Socket Desired Memory Pentium II Xeon Processor Upgrades Adding or Replacing a Pentium II Xeon Processor Slot 2 SEC Cartridge/Heat Sink Assembly Removal See Using the System Setup Program Replacing the System BatterySystem Battery and Battery Socket Obtaining technical assistance Drive Locations Removing and Replacing the Front BezelRemoving and Replacing Front-Panel Inserts Connecting DrivesDC Power Cable Connector Installing a Drive in a 5.25-Inch Drive BayRemoving a Drive Inserting the New Drive Into the Drive Bay Eide Drive Addressing Installing an Eide Hard-Disk Drive10. Removing the Hard-Disk Drive Bracket 11. Inserting a 1-Inch Hard-Disk Drive Into the Bracket 13. Attaching Hard-Disk Drive Cables Installing Scsi Devices Scsi Configuration GuidelinesScsi ID Numbers General Procedure for Installing Scsi Devices Device TerminationScsi Cables ALERT! Cover was previously removed Partitioning and Formatting Scsi Hard-Disk Drives Table A-1. Technical Specifications Processor System InformationExpansion Bus Ports and Connectors System ClocksDrives Key Combinations Controls and IndicatorsPhysical Page Jumpers and Switches-A General Explanation SwitchesJumpers Reserved do not remove jumper PARALLEL/SCSI System Board LabelsSerial and Parallel Ports Ports and ConnectorsSerial Port Connectors Parallel Port Connector Dparh External Scsi ConnectorKeyboard Connector Keyboard and Mouse ConnectorsVideo Connector NIC ConnectorMouse Connector Microphone Jack USB ConnectorsLine-Out Jack Interrupt AssignmentsLine-In Jack Table B-9. Interrupt Assignments IRQ Line Used By/AvailableTable B-10. Conventional Memory Map Address Range Use Memory AllocationsTable B-11. Upper Memory Map Address Range Use ICU Error Messages Table C-1. Configuration Utility Messages Probable CauseCorrective Action Listed Card or Adding an Unlisted Card for instructions Configuration Manager Messages Table C-2. Configuration Manager MessagesChange to the db subdirectory on the diskette drive Page Cards mentioned Page Backup Devices Scheduling BackupsRecovering Data Data PreservationCleaning System Components Recommended Tools and AccessoriesCleaning the Computer, Monitor, and Keyboard Exteriors Temperature Cleaning DrivesEnvironmental Factors HumidityDust and Particles AltitudeCorrosion ESDPower Source Interruptions MagnetismShock and Vibration Power Protection Devices Overview FCC Notices U.S. Only IC Notice Canada OnlyClass a Class B EN 55022 Compliance Czech Republic Only CE Notice European UnionVcci Notice Japan Only Class a ITEMOC Notice South Korea Only Class B ITEClass a Device Class B Device Polish Center for Testing and Certification NoticeExporter NOM Information Mexico OnlyOne Dell Way Round Rock, TXInformación para NOM únicamente para México Overview Limited Three-Year Warranty U.S. and Canada Only Coverage During Year OneCoverage During Years Two and Three General Total Satisfaction Return Policy U.S. and Canada OnlyADI AcpiAGP AsciiAspi AsicBBS BiosBTU Cmos CD-ROMDAT CPUDIN DimmDIP DMADpms DmtfDram DTEECP ECCEeprom EideEMS EpromFAT FTP FCCHMA GUIHpfs IcesIRQ IPXISA ITEXMM LANLVD LED
Related manuals
Manual 96 pages 49.66 Kb Manual 230 pages 48.24 Kb
Top Page Image Contents