Muratec MFX-3050 manual Loading paper, Tray

Page 30

Media type

 

 

Guidelines

 

 

 

Transparencies

•

To avoid damaging the machine, use only

 

 

transparencies designed for use in laser printers.

 

•

Transparencies used in the machine must be

 

 

able to withstand 180 °C, the machine’s fusing

 

 

temperature.

 

• Place them on a flat surface after removing them

 

 

from the machine.

 

•

Do not leave them in the paper tray for long

 

 

periods of time. Dust and dirt may accumulate

 

 

on them, resulting in spotty printing.

 

•

To avoid smudging caused by fingerprints,

 

 

handle them carefully.

 

•

To avoid fading, do not expose printed

 

 

transparencies to prolonged sunlight.

 

•

Ensure that transparencies are not wrinkled,

 

 

curled, or have any torn edges.

 

 

 

Labels

•

To avoid damaging the machine, use only labels

 

 

designed for use in laser printers.

 

•

When selecting labels, consider the following

 

 

factors:

 

 

-

Adhesives: The adhesive material should be

 

 

 

stable at 180 °C, the machine’s fusing

 

 

 

temperature.

 

 

-

Arrangement: Only use labels with no

 

 

 

exposed backing between them. Labels can

 

 

 

peel off sheets that have spaces between the

 

 

 

labels, causing serious jams.

 

 

-

Curl: Prior to printing, labels must lie flat with

 

 

 

no more than 13 mm of curl in any direction.

 

 

-

Condition: Do not use labels with wrinkles,

 

 

 

bubbles, or other indications of separation.

 

•

Make sure that there is no exposed adhesive

 

 

material between labels. Exposed areas can

 

 

cause labels to peel off during printing, which

 

 

can cause paper jams. Exposed adhesive can

 

 

also cause damage to machine components.

 

• Do not run a sheet of labels through the machine

 

 

more than once. The adhesive backing is

 

 

designed for only a single pass through the

 

 

machine.

 

•

Do not use labels that are separating from the

 

 

backing sheet or are wrinkled, bubbled, or

 

 

otherwise damaged.

 

 

 

Card stock or

•

Do not print on media smaller than 98 mm wide

custom-sized

 

or 148 mm long.

materials

•

In the software application, set margins at least

 

 

6,4 mm away from the edges of the material.

 

 

 

 

Media type

 

Guidelines

 

 

 

Preprinted

•

Letterhead must be printed with heat-resistant

paper

 

ink that will not melt, vaporize, or release

 

 

hazardous emissions when subjected to the

 

 

machine’s fusing temperature of 180 °C for

 

 

0,1 second.

 

•

Letterhead ink must be non-flammable and

 

 

should not adversely affect printer rollers.

 

•

Forms and letterhead should be sealed in a

 

 

moisture-proof wrapping to prevent changes

 

 

during storage.

 

•

Before you load preprinted paper, such as forms

 

 

and letterhead, verify that the ink on the paper is

 

 

dry. During the fusing process, wet ink can come

 

 

off preprinted paper, reducing print quality.

 

 

 

Loading paper

In the tray 1

Load the print media you use for the majority of your print jobs in the tray 1. The tray 1 can hold a maximum of 250 sheets of 75 g/m2 plain paper.

You can purchase an optional tray (tray 2) and attach it below the standard tray to load an additional 250 sheets of paper. For order information for an optional tray, see page 12.1.

The paper level indicator on the front of the tray 1 and the optional tray 2 shows the amount of paper currently left in the tray. When the tray is empty, the indicator of the bar is completely lowered.

Full

Empty

5.5 <Loading originals and print media>

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Page Page Contents Ordering supplies and accessories Fax setupUsing USB flash memory Basic printingInstalling accessories MaintenanceTroubleshooting SpecificationsImportant Precautions and Safety Information Canadian Radio Interference Regulations FCC Information to the UserApprovals and Certifications You should also know thatLimited warranty Page Special features IntroductionPrinter overview Front view Rear viewOn Hook Dial Engages the telephone line Control panel overviewMFX-3050 OK Confirms the selection on the screen Start Starts a jobUnderstanding the Status LED Finding more informationSelecting a location Clearance spaceNetwork System Setup Scan Setup System setupCopy Setup Scan Feature Menu overviewChanging the clock mode Setting the date and timeChanging the default mode Changing the display languageSetting sounds Entering characters using the number keypadUsing the save modes Setting print job timeoutSoftware overview Supplied softwareSystem requirements Printer driver featuresPostScript Feature WindowsLinux MacintoshRequirements Via network administration programs Network setupConfiguring TCP/IP Supported operating systemsDynamic addressing BOOTP/DHCP Configuring EtherTalkConfiguring IPX frame types Static addressingSetting Ethernet speed Restoring the network configurationPrinting a network configuration On the scanner glass Loading originals and print mediaLoading originals ADFSelecting print media Type Size Dimensions Weight1 Capacity2 Supported print media types and sizesMedia sizes supported in each mode Guidelines for selecting and storing print mediaGuidelines for special print media Loading paper TrayLoading paper in the tray 1 or optional tray Changing the size of the paper in the paper trayMulti-purpose tray Load the paper with the side to be printed on facing upSetting the paper size and type Selecting an output locationPrinting to the output tray Printing to the rear cover Selecting the paper tray Changing the settings for each copyCopying DarknessReduced or enlarged copy Changing the default copy settingsUsing special copy features CollationID card copying Poster copyingPlace Front Side and PressStart appears on the display Clone copying Setting copy timeoutCopying on both sides of paper Erasing background imagesPrinting a document Canceling a print jobBasic printing Double-click the Samsung SCX-5x30 Series iconScanning basics Scanning to an application using a local ConnectionScanning Press Scan/EmailScanning using a network connection Preparing for network scanningScanning to a network client Setting up an SMB serverClick Machine Settings and SMB Setup Click Server List ScanningSetting network scan timeout Scanning to EmailScanning to an FTP server Setting up Address Book Changing the settings for each scan jobChanging the default scan settings Scanning to an SMB serverSearching Address Book for an entry Configuring group email numbersUsing Address Book entries Printing Address BookResolution Setting the fax headerAdjusting the document settings Press ResolutionSending a fax automatically Sending a fax manuallyRedialing the last number Confirming a transmissionAutomatic redialing Changing receiving modesReceiving manually using an extension Telephone Receiving automatically in Fax modeReceiving manually in Tel mode Receiving automatically in Ans/Fax modeDeactivating secure receiving mode Receiving in secure receiving modeActivating secure receiving mode Receiving faxes in memoryPress Fax Printing received faxes on both sides of paperSending a fax to multiple destinations Down on the scanner glassCanceling a delayed fax Sending a delayed faxAdding pages to a delayed fax Sending a priority faxForwarding sent faxes to email address Forwarding faxesForwarding sent faxes to another fax machine Forwarding received faxes to another fax machineSending options Fax setupChanging the fax setup options Receiving optionsPrinting sent fax report automatically Changing the default document settingsSetting up Phone Book Speed buttonsSpeed dial numbers Group dial numbersSearching Phone Book for an entry Deleting a Phone Book entryPrinting Phone Book Plugging in a USB memory device Using USB flash memoryAbout USB memory Scanning to a USB memory devicePrinting from a USB memory device Customizing Scan to USBBacking up data Managing USB memoryFormatting a USB memory device Viewing the USB memory statusAccessory Description Part number Ordering supplies and accessoriesAccessories Toner cartridgesPrinting a report MaintenancePrinting reports Other available reportsCleaning the inside Cleaning your machineCleaning the outside Clearing memoryCleaning the scan unit Maintaining the toner cartridgeToner cartridge storage Redistributing toner Expected cartridge lifeCleaning the drum Replacing the toner cartridgeSending new toner notification Maintenance PartsPrinting continuously when the Toner Empty message appears Clearing the Toner Empty Replace Toner messageChecking replaceables Replacing the ADF rubber padTo access SyncThru Web Service Managing your machine from the webChecking the machine’s serial number Troubleshooting Clearing document jamsClearing paper jams Roller misfeedOptional tray Multi-purpose tray Fuser area or around the toner cartridgePaper exit area Duplex unit area Duplex JamTips for avoiding paper jams Understanding display messages Low Heat Error Message Meaning Suggested solutions Invalid ServerLine Error Cycle PowerTemperature Message Meaning Suggested solutions Retry Redial?Self Diagnostic Send ErrorToner cartridge-related messages Solving other problems Paper feeding problemsPrinting problems SCX-5x30 Series PCL Settings and then PrintersSpool Settings button Properties, click the DetailsPrinting quality problems Characters Condition Suggested solutions Wrinkles or creasesMisformed Back of printoutsCurl Copying problemsThis option through Printer Settings Utility or Software Section for detailsScanning problems Network Scan problems Fax problemsProblem Possible Cause Solution Common Windows problemsCommon PostScript problems Installable Options sectionCommon Linux problems Problem Possible Cause and SolutionCommon Macintosh problems Problem Suggested solutionsInstalling a memory Dimm Installing accessoriesPrecautions when installing accessories Disconnect the power cordActivating the added memory in the PS printer properties Select the Samsung SCX-5x30 Series PS printerSpecifications General specificationsPrinter specifications Scanner and copier specifications Facsimile specificationsIndex NumericsSystem requirements Macintosh Software section Contents Using Windows Postscript Driver Using Your Printer in Linux Typical Installation Installing Printer SoftwareInstalling Software for Local Printing Select Typical installation for a local printer. Click NextCustom Installation Select Custom installation. Click Next Select the components to be installed and click NextInstalling Software for Network Printing Custom Installation Installing Printer Software in Windows Reinstalling Printer Software Select the components you want to reinstall and click NextRemoving Printer Software NextPrinting a Document Printing to a file PRNSelect your printer driver from the Name drop-down list Printer Settings Layout TabPaper Orientation Paper Tab SourceScaling Printing Toner Save Mode Image ModeResolution Graphics TabExtras Tab About TabPrinter Tab Using a Favorite Setting Using HelpAdvanced Printing Printing Multiple Pages on One Sheet of Paper N-Up PrintingPrinting Posters Printing BookletsFitting Your Document to a Selected Paper Size Printing on Both Sides of PaperPrinting a Reduced or Enlarged Document NoneCreating a Watermark Using WatermarksUsing an Existing Watermark Editing a WatermarkUsing a Page Overlay Using OverlaysWhat is an Overlay? Creating a New Page OverlayUsing Windows PostScript Driver AdvancedUsing Direct Print Utility Overview Direct Print UtilityCheck the Share this printer box Setting Up a Host ComputerSetting Up a Client Computer Select Local Port and click New PortUnderstanding Smart Panel Troubleshooting GuidePrinter Setting Toner LevelChanging the Smart Panel Program Settings Opening the Troubleshooting GuideUsing Printer Settings Utility Using Onscreen Help FileScanning Using SmarThru Uninstalling SmarThruUsing SmarThru Scanning Process with TWAIN- enabled Software Scanning Using the WIA DriverSettings Installing the Unified Linux Driver Installing the Unified Linux DriverGetting Started Uninstalling the Unified Linux Driver Click UninstallOpening the Unified Driver Configurator Using the Unified Driver ConfiguratorPrinters Configuration Printers TabClasses Tab Scanners ConfigurationPorts Configuration Sharing Ports Between Printers and ScannersConfiguring Printer Properties Printing a Document Printing from ApplicationsScanning a Document Printing FilesClick Properties Using the Image Manager Adding Job Type SettingsTools Function 10Using Your Printer with a Macintosh Installing Software for MacintoshUninstalling the Scan driver Setting Up the PrinterInstall the Scan driver For a Network-connected MacintoshPrinting Changing Printer SettingsLayout Setting Printing a DocumentPrinting Multiple Pages on One Sheet of Paper Printer Features SettingResolutionQuality Fit toScanning Duplex PrintingIndex Rev.1.05
Related manuals
Manual 2 pages 7.5 Kb

MFX-3050 specifications

The Muratec MFX-3050 is a multifunctional printer designed to meet the demands of modern workplaces with its versatile features and advanced technology. This compact and robust device excels in delivering printing, copying, scanning, and faxing capabilities, making it an ideal solution for small to medium-sized businesses.

One of the standout characteristics of the MFX-3050 is its impressive print speed. Capable of producing up to 30 pages per minute, it ensures that users can efficiently complete their printing tasks without unnecessary delays. This speed is complemented by its first-page-out time, which is remarkably quick, allowing users to receive their documents almost instantly.

In terms of print quality, the MFX-3050 does not disappoint. With a maximum print resolution of 1200 dpi, it provides sharp and vibrant documents, suitable for both text and graphics. This high-quality output is essential for professionals who need to make a strong impression with their documentation.

The device features a user-friendly interface, equipped with a color touchscreen display that simplifies operation. Users can easily navigate through various functions, adjust settings, and monitor job status, enhancing overall productivity. The MFX-3050 also offers a range of connectivity options, including USB, Ethernet, and Wi-Fi, allowing seamless integration into any office network.

Another significant advantage of the MFX-3050 is its scanning capabilities. With the ability to scan at 600 dpi and a robust automatic document feeder, users can quickly digitize multi-page documents. The device supports various file formats, making it easy to share scanned files across different platforms.

Security is a crucial consideration for any office environment, and the MFX-3050 addresses this concern with built-in security features. These include secure print, user authentication, and data encryption, ensuring that sensitive information remains protected.

Furthermore, the MFX-3050 is designed with environmental considerations in mind. It is ENERGY STAR certified, showcasing its efficiency and commitment to reducing energy consumption without compromising performance.

In summary, the Muratec MFX-3050 is a reliable multifunction printer that combines speed, quality, and security in one compact unit. Whether for printing, copying, scanning, or faxing, it offers a robust solution tailored for the dynamic needs of today's business environment. With its advanced features and user-centric design, the MFX-3050 is an excellent investment for any organization seeking to enhance their productivity and efficiency.
Top Page Image Contents