Muratec MFX-3050 manual Installing accessories, Precautions when installing accessories

Page 91

15 Installing accessories

Your machine is a full-featured MFP that has been optimized to meet most of your printing needs. Recognizing that each user may have different requirements, however, Muratec makes several accessories available to enhance your machine’s capabilities.

This chapter includes:

•Precautions when installing accessories

•Installing a memory DIMM

Precautions when installing accessories

Disconnect the power cord

Never remove the control board cover while the power is being supplied.

To avoid the possibility of an electrical shock, always disconnect the power cord when installing or removing ANY internal or external accessories.

Discharge static electricity

The control board and internal accessories (network interface card or memory DIMM) are sensitive to static electricity. Before installing or removing an internal accessories, discharge static electricity from your body by touching something metal, such as the metal back plate on any device plugged into a grounded power source. If you walk round before finishing installation, discharge any static electricity once again.

Installing a memory DIMM

Your machine has a dual in-line memory module (DIMM) slot. Use this DIMM slot to install additional memory.

The MFX-3050 has 96 MB of standard memory. It can be expanded to 320 MB.

Users must remove the preinstalled memory DIMM before upgrading the memory.

Contact your authorized Muratec dealer to order additional memory.

1Turn the machine off and unplug all cables from the machine.

2Grasp the control board cover and slide toward you to open it.

1

1 control board cover

3Completely open the latch on each side of the DIMM slot. Remove the preinstalled memory DIMM.

1

2

1 latch

2 memory DIMM

4Take out a new memory DIMM from the plastic bag.

5Holding the memory DIMM by the edges, align the notches on the memory DIMM with the grooves on the memory DIMM slot.

Note

The notches and grooves illustrated above may not match those on an actual DIMM and the slot.

15.1 <Installing accessories>

Page 90 Page 92
Image 91
Page 90 Page 92
Contents Page Page Contents Basic printing Fax setupUsing USB flash memory Ordering supplies and accessoriesSpecifications MaintenanceTroubleshooting Installing accessoriesImportant Precautions and Safety Information FCC Information to the User Canadian Radio Interference RegulationsYou should also know that Approvals and CertificationsLimited warranty Page Introduction Special featuresFront view Rear view Printer overviewOK Confirms the selection on the screen Start Starts a job Control panel overviewMFX-3050 On Hook Dial Engages the telephone lineFinding more information Understanding the Status LEDClearance space Selecting a locationMenu overview System setupCopy Setup Scan Feature Network System Setup Scan SetupChanging the display language Setting the date and timeChanging the default mode Changing the clock modeEntering characters using the number keypad Setting soundsSetting print job timeout Using the save modesSupplied software Software overviewWindows Printer driver featuresPostScript Feature System requirementsMacintosh LinuxRequirements Supported operating systems Network setupConfiguring TCP/IP Via network administration programsStatic addressing Configuring EtherTalkConfiguring IPX frame types Dynamic addressing BOOTP/DHCPRestoring the network configuration Setting Ethernet speedPrinting a network configuration ADF Loading originals and print mediaLoading originals On the scanner glassSelecting print media Supported print media types and sizes Type Size Dimensions Weight1 Capacity2Guidelines for selecting and storing print media Media sizes supported in each modeGuidelines for special print media Tray Loading paperChanging the size of the paper in the paper tray Loading paper in the tray 1 or optional trayLoad the paper with the side to be printed on facing up Multi-purpose traySelecting an output location Setting the paper size and typePrinting to the output tray Printing to the rear cover Darkness Changing the settings for each copyCopying Selecting the paper trayCollation Changing the default copy settingsUsing special copy features Reduced or enlarged copyPoster copying ID card copyingPlace Front Side and PressStart appears on the display Erasing background images Setting copy timeoutCopying on both sides of paper Clone copyingDouble-click the Samsung SCX-5x30 Series icon Canceling a print jobBasic printing Printing a documentPress Scan/Email Scanning to an application using a local ConnectionScanning Scanning basicsPreparing for network scanning Scanning using a network connectionScanning Setting up an SMB serverClick Machine Settings and SMB Setup Click Server List Scanning to a network clientScanning to Email Setting network scan timeoutScanning to an FTP server Scanning to an SMB server Changing the settings for each scan jobChanging the default scan settings Setting up Address BookPrinting Address Book Configuring group email numbersUsing Address Book entries Searching Address Book for an entryPress Resolution Setting the fax headerAdjusting the document settings ResolutionSending a fax manually Sending a fax automaticallyChanging receiving modes Confirming a transmissionAutomatic redialing Redialing the last numberReceiving automatically in Ans/Fax mode Receiving automatically in Fax modeReceiving manually in Tel mode Receiving manually using an extension TelephoneReceiving faxes in memory Receiving in secure receiving modeActivating secure receiving mode Deactivating secure receiving modeDown on the scanner glass Printing received faxes on both sides of paperSending a fax to multiple destinations Press FaxSending a priority fax Sending a delayed faxAdding pages to a delayed fax Canceling a delayed faxForwarding received faxes to another fax machine Forwarding faxesForwarding sent faxes to another fax machine Forwarding sent faxes to email addressReceiving options Fax setupChanging the fax setup options Sending optionsSpeed buttons Changing the default document settingsSetting up Phone Book Printing sent fax report automaticallyGroup dial numbers Speed dial numbersDeleting a Phone Book entry Searching Phone Book for an entryPrinting Phone Book Scanning to a USB memory device Using USB flash memoryAbout USB memory Plugging in a USB memory deviceCustomizing Scan to USB Printing from a USB memory deviceManaging USB memory Backing up dataViewing the USB memory status Formatting a USB memory deviceToner cartridges Ordering supplies and accessoriesAccessories Accessory Description Part numberOther available reports MaintenancePrinting reports Printing a reportClearing memory Cleaning your machineCleaning the outside Cleaning the insideMaintaining the toner cartridge Cleaning the scan unitToner cartridge storage Expected cartridge life Redistributing tonerReplacing the toner cartridge Cleaning the drumClearing the Toner Empty Replace Toner message Maintenance PartsPrinting continuously when the Toner Empty message appears Sending new toner notificationReplacing the ADF rubber pad Checking replaceablesManaging your machine from the web To access SyncThru Web ServiceChecking the machine’s serial number Clearing document jams TroubleshootingRoller misfeed Clearing paper jamsFuser area or around the toner cartridge Optional tray Multi-purpose trayPaper exit area Duplex Jam Duplex unit areaTips for avoiding paper jams Understanding display messages Cycle Power Message Meaning Suggested solutions Invalid ServerLine Error Low Heat ErrorSend Error Message Meaning Suggested solutions Retry Redial?Self Diagnostic TemperatureToner cartridge-related messages Paper feeding problems Solving other problemsPrinting problems Properties, click the Details Settings and then PrintersSpool Settings button SCX-5x30 Series PCLPrinting quality problems Back of printouts Condition Suggested solutions Wrinkles or creasesMisformed CharactersSoftware Section for details Copying problemsThis option through Printer Settings Utility or CurlScanning problems Fax problems Network Scan problemsInstallable Options section Common Windows problemsCommon PostScript problems Problem Possible Cause SolutionProblem Possible Cause and Solution Common Linux problemsProblem Suggested solutions Common Macintosh problemsDisconnect the power cord Installing accessoriesPrecautions when installing accessories Installing a memory DimmSelect the Samsung SCX-5x30 Series PS printer Activating the added memory in the PS printer propertiesGeneral specifications SpecificationsPrinter specifications Facsimile specifications Scanner and copier specificationsNumerics IndexSystem requirements Macintosh Software section Contents Using Windows Postscript Driver Using Your Printer in Linux Select Typical installation for a local printer. Click Next Installing Printer SoftwareInstalling Software for Local Printing Typical InstallationCustom Installation Select the components to be installed and click Next Select Custom installation. Click NextInstalling Software for Network Printing Custom Installation Installing Printer Software in Windows Select the components you want to reinstall and click Next Reinstalling Printer SoftwareNext Removing Printer SoftwarePrinting to a file PRN Printing a DocumentSelect your printer driver from the Name drop-down list Layout Tab Printer SettingsPaper Orientation Source Paper TabScaling Printing Graphics Tab Image ModeResolution Toner Save ModeAbout Tab Extras TabPrinter Tab Using Help Using a Favorite SettingPrinting Multiple Pages on One Sheet of Paper N-Up Printing Advanced PrintingPrinting Booklets Printing PostersNone Printing on Both Sides of PaperPrinting a Reduced or Enlarged Document Fitting Your Document to a Selected Paper SizeEditing a Watermark Using WatermarksUsing an Existing Watermark Creating a WatermarkCreating a New Page Overlay Using OverlaysWhat is an Overlay? Using a Page OverlayAdvanced Using Windows PostScript DriverOverview Direct Print Utility Using Direct Print UtilitySelect Local Port and click New Port Setting Up a Host ComputerSetting Up a Client Computer Check the Share this printer boxToner Level Troubleshooting GuidePrinter Setting Understanding Smart PanelUsing Onscreen Help File Opening the Troubleshooting GuideUsing Printer Settings Utility Changing the Smart Panel Program SettingsUninstalling SmarThru Scanning Using SmarThruUsing SmarThru Scanning Using the WIA Driver Scanning Process with TWAIN- enabled SoftwareSettings Installing the Unified Linux Driver Installing the Unified Linux DriverGetting Started Click Uninstall Uninstalling the Unified Linux DriverPrinters Tab Using the Unified Driver ConfiguratorPrinters Configuration Opening the Unified Driver ConfiguratorSharing Ports Between Printers and Scanners Scanners ConfigurationPorts Configuration Classes TabPrinting from Applications Configuring Printer Properties Printing a DocumentPrinting Files Scanning a DocumentClick Properties Adding Job Type Settings Using the Image ManagerTools Function Installing Software for Macintosh 10Using Your Printer with a MacintoshFor a Network-connected Macintosh Setting Up the PrinterInstall the Scan driver Uninstalling the Scan driverPrinting a Document Changing Printer SettingsLayout Setting PrintingFit to Printer Features SettingResolutionQuality Printing Multiple Pages on One Sheet of PaperDuplex Printing ScanningIndex Rev.1.05
Related manuals
Manual 2 pages 7.5 Kb

MFX-3050 specifications

The Muratec MFX-3050 is a multifunctional printer designed to meet the demands of modern workplaces with its versatile features and advanced technology. This compact and robust device excels in delivering printing, copying, scanning, and faxing capabilities, making it an ideal solution for small to medium-sized businesses.

One of the standout characteristics of the MFX-3050 is its impressive print speed. Capable of producing up to 30 pages per minute, it ensures that users can efficiently complete their printing tasks without unnecessary delays. This speed is complemented by its first-page-out time, which is remarkably quick, allowing users to receive their documents almost instantly.

In terms of print quality, the MFX-3050 does not disappoint. With a maximum print resolution of 1200 dpi, it provides sharp and vibrant documents, suitable for both text and graphics. This high-quality output is essential for professionals who need to make a strong impression with their documentation.

The device features a user-friendly interface, equipped with a color touchscreen display that simplifies operation. Users can easily navigate through various functions, adjust settings, and monitor job status, enhancing overall productivity. The MFX-3050 also offers a range of connectivity options, including USB, Ethernet, and Wi-Fi, allowing seamless integration into any office network.

Another significant advantage of the MFX-3050 is its scanning capabilities. With the ability to scan at 600 dpi and a robust automatic document feeder, users can quickly digitize multi-page documents. The device supports various file formats, making it easy to share scanned files across different platforms.

Security is a crucial consideration for any office environment, and the MFX-3050 addresses this concern with built-in security features. These include secure print, user authentication, and data encryption, ensuring that sensitive information remains protected.

Furthermore, the MFX-3050 is designed with environmental considerations in mind. It is ENERGY STAR certified, showcasing its efficiency and commitment to reducing energy consumption without compromising performance.

In summary, the Muratec MFX-3050 is a reliable multifunction printer that combines speed, quality, and security in one compact unit. Whether for printing, copying, scanning, or faxing, it offers a robust solution tailored for the dynamic needs of today's business environment. With its advanced features and user-centric design, the MFX-3050 is an excellent investment for any organization seeking to enhance their productivity and efficiency.
Top Page Image Contents