Opticon LMD 1135 user manual Transmitting Error Indications Trigger Enabled only

Page 69

Manual No. 25-ULPNR102-01; Mar, 2005

LMD 1135 Laser Fixed Mount Scanner

35. Transmitting Error Indications (Trigger Enabled only)

Computer	Function	Bar Code
Command	/Description	Command
(ZZ)	START/END	[[
	Programming Menu

TH	Error message no label	UI


TI	Error message no decode	UJ


TG	Clear error messages for no label	UH
	and no decode

WD	Disable response to command	XE


WC	Enable response to command	XD
	OK=ACK, ERROR=NAK

WB	Buzzer Control to Command –	XC
	Disable

WA	Buzzer Control to Command –	XB
	Enable

Error Messages – No decode / no label

%

%

Messages may be user defined for the “no decode” and “no label” error modes independently. Using the “Error message no label” (TH) and “Error message no decode” (TI) menu commands a maximum of 4 characters may be user specified for transmission should these errors occur.

The following process should be followed to designate these error codes:

1.Scan “START” to enter the programming mode.

2Scan “Error message no label” (TH).

3.Scan bar codes of the desired error message characters (4 max)

4.Scan “END” to end the programming sequence.

In a similar fashion, the “Error message no decode” (TI) can be defined.

Page 65

Image 69

Contents User’s Manual Manual No -ULPNR102-01 March OSE Command SetPage Contents Configuring the Scanner Technical SpecificationsScanner Servicing and Maintenance Introduction and Getting StartedQuick Start-Up Procedure Section Introduction and Getting StartedProduct Overview Page Section Technical Specifications Physical SpecificationsOptical Specifications Avoid specular reflection in the dead zone +/- 8 degrees JAN 13 R = 30 mm 1.2 or Electrical SpecificationsConnector Pin-outs RS232 Communications SpecificationsRS232 Signal Level RS232 Transmit / Receive Character FormatPin No Signal Environmental SpecificationsOrdering Information ModelAchieving Optimum Performance Section Positioning the Scanner for Optimum PerformanceDistance to the Bar Code Depth-of-FieldDistance Max From Window Width Avoiding Specular ReflectionQuality Bar Code Labels Measuring Scanner PerformanceTips for Insuring Highest Data Integrity Application Notes Tips for Achieving High ThroughputTips for Verifying the Presence of a Bar Code Programming Menus & Commands Section Configuring the ScannerDefault Settings Parameter Factory Default SettingTechnical Assistance and Support Section Application Engineering SupportCommon Causes of Poor Performance Modified and/or Customized ScannersSection Scanner Servicing and Maintenance Section Scanner LabelingIEC 825-1 Class 1 Laser Device Appendices Appendix a ESC Computer Command CRWhat if you make a mistake? Reset All Defaults U2 Command U2Symbology Selection Global DefaultsOptions for UPC Options for EAN-8 & EAN-13Options for Code Prefix/Suffix Select Symbology forPrefix/Suffix of Numeric Characters Prefix/Suffix of Alpha CharactersSelecting the Read Mode Setting the Trigger & Auto-TriggerParallel Read Mode HandshakingXmit Error Trigger Enabled Mode only Scanner Timeout Trigger EnabledMode Quiet Zone OptionsAppendix C Command Description Global Default & Scanner ConfigurationsComputer Including prefix/suffixDescription Command Symbology SelectionSymbologies Bar CodeOnly EAN 13/8 +2 START/END Add/Activate Specific Bar Code SymbologiesDelete/Deactivate Specific Bar Code Symbologies Add/Activate Specific Bar Code SymbologiesDisable all symbologies Options for UPC Bar Code Command DescriptionOptions for EAN-8 & EAN-13 Options for Code 39 & IT Pharmaceutical IT Pharmaceutical, enable Transmit of leading a Options for Codabar NW-7 Codabar NW-7 Format 5 Format Standard and Interleaved Options for Interleaved & Industrial 2String format Options for IataMeaning of Acronym Number of digits 15 totalOptions for Code-93 Options for Code-128 / EAN-128Fixing the Number of Digits Disable fixed length allCreating a Prefix and/or Suffix UPC-E +2 or +5 Setting Prefixes Identifying the SymbologyMSI/Plessey Setting Suffixes Identifying the Symbology Bar Code Command Description Direct Input of Numeric Characters Direct Input of Alpha Characters Direct Input of Alpha Characters Lower Case Direct Input of Control Characters ETBSUB Direct Input Characters Misc Bar Code Command Description START/END Code Identification & Characters/Digits TransmittedCommunication Parameters Communication Parameters Terminal HandshakingMs intercharacter delay Buzzer Operation Disable buzzerPositive & Negative Bar Codes Setting the Trigger & Auto-Trigger FunctionsTrigger Function Enabled S8 Trigger Function Disabled S7 Selecting the Read ModeParallel Read Mode Add-on Wait Mode Applies to UPC/EAN onlyParallel labels only Scanner Timeout Trigger Enabled Mode only Multiple Read Reset Time Quiet Zone Options Redundant Decoding Error Messages No decode / no label Transmitting Error Indications Trigger Enabled onlyGood Read LED Operation Appendix D Appendix E