Opticon LMD 1135 Scanner Timeout Trigger Enabled, Mode, Quiet Zone Options, Redundant Decoding

Page 27

Manual No. 25-ULPNR102-01; Mar, 2005

LMD 1135 Laser Fixed Mount Scanner

	Scanner Timeout (Trigger Enabled
	Mode)
Y1	1 second after triggering
Y2	2 second after triggering
Y3	3 second after triggering
Y4	4 second after triggering
Y5	5 seconds after triggering
Y6	6 second after triggering
Y7	7 seconds after triggering
Y8	8 seconds after triggering
Y9	9 seconds after triggering
YL	Read time x 10
YM	Indefinitely after triggering

XA	Add-on Wait Time - Disable
XB	Add-on Wait Time – 250 msec
XC	Add-on Wait Time – 500 msec
XD	Add-on Wait Time – 750 msec

AH	Multiple Read Reset Time – 50 msec
AI	Multiple Read Reset Time – 100 msec
AJ	Multiple Read Reset Time – 200 msec
AK	Multiple Read Reset Time – 300 msec
AL	Multiple Read Reset Time – 400 msec
AM	Multiple Read Reset Time – 500 msec
AN	Multiple Read Reset Time – 600 msec
AG	Multiple Read Reset Time - Indefinite

	Quiet Zone Options
YN	No margin check
YO	Margin check 1/7 nominal
YP	Margin check 2/7 nominal
YQ	Margin check 3/7 nominal

YR	Margin check 4/7 nominal
YS	Margin check 5/7 nominal
YT	Margin check 6/7 nominal
YU	Margin check normal

	Redundant Decoding
X0	Read bar code once
X1	Read bar code twice before transmitting
X2	Read bar code three times before transmitting
X3	Read bar code four times before transmitting
BS	Read bar code five times before transmitting
BT	Read bar code six times before transmitting
BU	Read bar code seven times before xmitting
BV	Read bar code eight times before xmitting
BW	Read bar code nine times before xmitting

	Xmit Error (Trigger Enabled Mode only)
TH	User defined error message for no label
TI	User defined error message for no decode
TG	Clear error messages for no label, no decode

WD	Response to command - None
WC	Response to command – OK=ACK,
	ERROR=NAK

WB	Buzzer Control to Command - Disable
WA	Buzzer Control to Command - Enable

	Good Read LED Operation
T4	Disable good read LED (GRL)
T5	GRL ON for 0.20 seconds after decode
T6	GRL ON for 0.40 seconds after decode
T7	GRL ON for 0.80 seconds after decode

Page 23

Image 27

Contents User’s Manual Manual No -ULPNR102-01 March OSE Command SetPage Contents Introduction and Getting Started Technical SpecificationsConfiguring the Scanner Scanner Servicing and MaintenanceQuick Start-Up Procedure Section Introduction and Getting StartedProduct Overview Page Section Technical Specifications Physical SpecificationsOptical Specifications Avoid specular reflection in the dead zone +/- 8 degrees JAN 13 R = 30 mm 1.2 or Electrical SpecificationsRS232 Transmit / Receive Character Format RS232 Communications SpecificationsConnector Pin-outs RS232 Signal LevelModel Environmental SpecificationsPin No Signal Ordering InformationDepth-of-Field Section Positioning the Scanner for Optimum PerformanceAchieving Optimum Performance Distance to the Bar CodeDistance Max From Window Width Avoiding Specular ReflectionQuality Bar Code Labels Measuring Scanner PerformanceTips for Insuring Highest Data Integrity Application Notes Tips for Achieving High ThroughputTips for Verifying the Presence of a Bar Code Parameter Factory Default Setting Section Configuring the ScannerProgramming Menus & Commands Default SettingsModified and/or Customized Scanners Section Application Engineering SupportTechnical Assistance and Support Common Causes of Poor PerformanceSection Scanner Servicing and Maintenance Section Scanner LabelingIEC 825-1 Class 1 Laser Device Appendices Appendix a ESC Computer Command CRWhat if you make a mistake? Reset All Defaults U2 Command U2Options for EAN-8 & EAN-13 Global DefaultsSymbology Selection Options for UPCOptions for Code Prefix/Suffix of Alpha Characters Select Symbology forPrefix/Suffix Prefix/Suffix of Numeric CharactersHandshaking Setting the Trigger & Auto-TriggerSelecting the Read Mode Parallel Read ModeQuiet Zone Options Scanner Timeout Trigger EnabledXmit Error Trigger Enabled Mode only ModeAppendix C Including prefix/suffix Global Default & Scanner ConfigurationsCommand Description ComputerBar Code Symbology SelectionDescription Command SymbologiesOnly EAN 13/8 +2 START/END Add/Activate Specific Bar Code SymbologiesDelete/Deactivate Specific Bar Code Symbologies Add/Activate Specific Bar Code SymbologiesDisable all symbologies Options for UPC Bar Code Command DescriptionOptions for EAN-8 & EAN-13 Options for Code 39 & IT Pharmaceutical IT Pharmaceutical, enable Transmit of leading a Options for Codabar NW-7 Codabar NW-7 Format 5 Format Standard and Interleaved Options for Interleaved & Industrial 2Number of digits 15 total Options for IataString format Meaning of AcronymOptions for Code-93 Options for Code-128 / EAN-128Fixing the Number of Digits Disable fixed length allCreating a Prefix and/or Suffix UPC-E +2 or +5 Setting Prefixes Identifying the SymbologyMSI/Plessey Setting Suffixes Identifying the Symbology Bar Code Command Description Direct Input of Numeric Characters Direct Input of Alpha Characters Direct Input of Alpha Characters Lower Case Direct Input of Control Characters ETBSUB Direct Input Characters Misc Bar Code Command Description START/END Code Identification & Characters/Digits TransmittedCommunication Parameters Communication Parameters Terminal HandshakingMs intercharacter delay Buzzer Operation Disable buzzerPositive & Negative Bar Codes Setting the Trigger & Auto-Trigger FunctionsTrigger Function Enabled S8 Trigger Function Disabled S7 Selecting the Read ModeParallel Read Mode Add-on Wait Mode Applies to UPC/EAN onlyParallel labels only Scanner Timeout Trigger Enabled Mode only Multiple Read Reset Time Quiet Zone Options Redundant Decoding Error Messages No decode / no label Transmitting Error Indications Trigger Enabled onlyGood Read LED Operation Appendix D Appendix E