The Speaker Company M23 Charging the Battery, Battery Power, Status LED Power LED Description

Page 19

2.6 Charging the Battery

1.Open the printer supply door and remove the battery.

2.Insert the battery into the charger station.

Battery

Power

LED

Status LED

Power LED

Description

Red

Off

Power is on

Power is off

Status LED

Red

Amber

Green (Solid)

Green (Blinking)

Off

Description

Charging battery

Battery is 70% charged

Battery is completely charged

Charger error

No battery

Note:

1.If Power LED is solid red and Status LED is green blinking, please remove the battery and check if the terminals inside the charger are shorted by foreign object. Unplug the charger power adapter from the outlet and remove the object between “+” and “-“ terminals. Install the battery to the charger for charging again. If problem still exists, please contact your purchased reseller for service.

2.It takes 2 to 3 hours to fully charge the battery before the first time usage. The

Image 19

Contents USER’S Manual Contents Printer initialization Ignore AUTO.BAS Update Firmware Via Serial Port Update Firmware Via USB PortCompliances Copyright DeclarationWichtige Sicherheits-Hinweise Unpacking and Inspection Equipment ChecklistIntroduction DocumentationTear plate for label Peel roller Tear bar for liner Peel bar Front ViewPage Rear View Supply door Release button Install the BatteryLi-ion battery Release button Getting StartedHand strap Strap button Rings Using the StrapShoulder Strap Option Shoulder strap Roll of supplies Supply holder tabs Release button Loading MediaLabel Supply door Paper exit chute Loading Die-cut Labels Peel off enablers Peel rollerPeel roller Peeler bar Tear edge for liner Liner Roll of label Supply holder tabs Release buttonPaper core Label Liner Loading Fan-fold LabelsPaper guides Fan-fold paper entrance chute Fan-fold mediaRS232 port Cable cavity Null modem cable Connecting the Communication CableHinged Cable door Screws RS232 portHinged cable door Bluetooth Using the Bluetooth Wireless OptionalStatus LED Charging the BatteryBattery Power Status LED Power LED DescriptionPage Icon Description Using the Display and ButtonsLCD Display and Buttons Navigation buttons LCD display On/Off buttonLCD Display Icon Description Option LCD/Keyboard OperationSWI LCD Menu OverviewMain Menu Setup File ManagerPause Speed Ips SetupSpeed Direction DensityDirection DensityReference X & Reference Y Batch Mode Peeler ModePrint Mode Tear Off Mode/Batch Mode/Peeler Mode Offset001 002 850Auto Gap Gap Sensor Bline SensorAuto Gap Manual Gap Gap SensorGAP Calibrate Insert liner Then hit EnterCalibrating Stock AD = Manual Gap Gap Sensor Stock AD = Intension =Black Sensor Auto Bline Manual BlineInsert label Then hit Enter Bline CalibrateContinuous Manual BlineCalibrate 9600 bps 19200 bps Calibrate 100None Odd One Stop Bit Two Stop Bits 8 Data Bits ExitIP Address Subnet Mask Status ConfigureVersion 1.2 M23 WiFi TSC Wireless 00A0F8E2AD9E Protocol TCP State Unknow Radio Ieee 802.11bSubnet Mask 000.000.000.000 IP Address 000.000.000.000Gateway 000.000.000.000 Ssid PSP3Port +09100 ProtocolEscape Char Save Settings? Are you sure?Reset Escape Char +035Change PIN Disable ExitChange PIN 0000 SecurityInformation Local Name BT23Contract Local NameBacklight Disable EnableDisable 10 Seconds Low PowerFile Manager Disable 5 MinutesShut Down Dram 256 KB Free FLASH3072 KB Free To print out the self test data to a label DiagnosticsBattery Voltage = 7.33 Display Display Buttons English Exit LanguageParameter ServiceDefault setting Initialization Mileage InfoMileage 6m Labels 53pcs Ready Printing LabelsConnect with a Cable to Print Connect by Radio OptionalRF Network Stand-along PrintingBefore Stand-along Download the Format Start Stand-along Printing TroubleshootingProblem No Power Not Printing No Paper Possible Cause Recovery ProcedurePoor Print Quality Reduced Battery lifePaper Jam Tear Bar/Peel Bar Sensor Exterior Interior MaintenancePrinter Part Print Head Platen Roller Peel Roller Method IntervalIllustration for recommended cleaning parts Page Update Firmware Via Serial Port Firmware Update ProcedurePage Page Update Firmware Via USB Port Printer initialization Power on utilitiesInitializing Ignore AUTO.BAS Ignore AUTO.BASPage No.35, Sec , Ligong 1st Rd., Wujie Township