The Speaker Company M23 user manual Firmware Update Procedure, Update Firmware Via Serial Port

Page 61

8. Firmware Update Procedure

Both RS-232 and USB interfaces are available to upgrade printer firmware. Please refer to the firmware update procedures as below.

8.1 Update Firmware Via Serial Port

1.Set M23’s “Serial Comm.” setting as below. Baud Rate = 115200

Parity = No Parity Data Bits = 8 Data Bits Stop Bits = 1 Stop Bits

2.Printer is in ready mode.

Ready

ll

Method 1：In MS-DOS mode (Command Prompt), copy the firmware file (*.NEW) to printer via serial port.

(1) Set the PC’s COM port setting.

Please issue following command in command prompt mode to setup PC RS-232 communication parameters.

C:\>mode com1 baud=115200 parity=n data=8 stop=1 octs=on rts=on <Enter>

(2)Copy firmware file to M23 with binary copy parameter. C:\>copy M23_v06.NEW /b com1

58

Image 61

Contents USER’S Manual Contents Printer initialization Ignore AUTO.BAS Update Firmware Via Serial Port Update Firmware Via USB PortCompliances Copyright DeclarationWichtige Sicherheits-Hinweise Introduction Equipment ChecklistDocumentation Unpacking and InspectionTear plate for label Peel roller Tear bar for liner Peel bar Front ViewPage Rear View Li-ion battery Release button Install the BatteryGetting Started Supply door Release buttonHand strap Strap button Rings Using the StrapShoulder Strap Option Shoulder strap Roll of supplies Supply holder tabs Release button Loading MediaLabel Supply door Paper exit chute Loading Die-cut Labels Peel off enablers Peel rollerPeel roller Peeler bar Tear edge for liner Liner Roll of label Supply holder tabs Release buttonPaper core Label Liner Loading Fan-fold LabelsPaper guides Fan-fold paper entrance chute Fan-fold mediaHinged Cable door Screws Connecting the Communication CableRS232 port RS232 port Cable cavity Null modem cableHinged cable door Bluetooth Using the Bluetooth Wireless OptionalBattery Power Charging the BatteryStatus LED Power LED Description Status LEDPage LCD Display and Buttons Using the Display and ButtonsNavigation buttons LCD display On/Off button Icon DescriptionLCD Display Icon Description Option LCD/Keyboard OperationSWI LCD Menu OverviewMain Menu Setup File ManagerPause Speed Ips SetupSpeed Direction DensityDensity DirectionPrint Mode Tear Off Mode/Batch Mode/Peeler Mode Batch Mode Peeler ModeOffset Reference X & Reference Y001 002 850Auto Gap Manual Gap Gap Sensor Bline SensorGap Sensor Auto GapGAP Calibrate Insert liner Then hit EnterCalibrating Stock AD = Manual Gap Gap Sensor Stock AD = Intension =Insert label Then hit Enter Auto Bline Manual BlineBline Calibrate Black SensorContinuous Manual BlineCalibrate 9600 bps 19200 bps Calibrate 100None Odd One Stop Bit Two Stop Bits 8 Data Bits ExitVersion 1.2 M23 WiFi TSC Wireless Status Configure00A0F8E2AD9E Protocol TCP State Unknow Radio Ieee 802.11b IP Address Subnet MaskSubnet Mask 000.000.000.000 IP Address 000.000.000.000Gateway 000.000.000.000 Port +09100 PSP3Protocol SsidReset Save Settings? Are you sure?Escape Char +035 Escape CharChange PIN 0000 Disable ExitSecurity Change PINContract Local Name BT23Local Name InformationDisable 10 Seconds Disable EnableLow Power BacklightFile Manager Disable 5 MinutesShut Down Dram 256 KB Free FLASH3072 KB Free To print out the self test data to a label DiagnosticsBattery Voltage = 7.33 Display Display Buttons English Exit LanguageDefault setting ServiceInitialization Mileage Info ParameterMileage 6m Labels 53pcs Connect with a Cable to Print Printing LabelsConnect by Radio Optional ReadyRF Network Stand-along PrintingBefore Stand-along Download the Format Problem No Power Not Printing No Paper Possible Cause TroubleshootingRecovery Procedure Start Stand-along PrintingPoor Print Quality Reduced Battery lifePaper Jam Printer Part Print Head Platen Roller Peel Roller Method MaintenanceInterval Tear Bar/Peel Bar Sensor Exterior InteriorIllustration for recommended cleaning parts Page Update Firmware Via Serial Port Firmware Update ProcedurePage Page Update Firmware Via USB Port Printer initialization Power on utilitiesInitializing Ignore AUTO.BAS Ignore AUTO.BASPage No.35, Sec , Ligong 1st Rd., Wujie Township