The Speaker Company M23 user manual Mileage 6m Labels 53pcs, Mileage Info

Page 53

Bline Intension

LCD Contrast

Back Light off Time

Low Power Time

Shut Down Time

sensor

Will be reset. Need to re-calibrate the bline sensor

50

10 sec

Off

Off

Note : When printer initialization is done, please calibrate the gap or black mark sensor again.

4.5.2 Mileage Info.

Use this option to check the printed mileage (displayed in meter).

Mileage: 6(m)

Labels: 53(pcs.)



50

Image 53

Contents USER’S Manual Contents Printer initialization Ignore AUTO.BAS Update Firmware Via Serial Port Update Firmware Via USB PortWichtige Sicherheits-Hinweise Copyright DeclarationCompliances Introduction Equipment ChecklistDocumentation Unpacking and InspectionTear plate for label Peel roller Tear bar for liner Peel bar Front ViewPage Rear View Li-ion battery Release button Install the BatteryGetting Started Supply door Release buttonHand strap Strap button Rings Using the StrapShoulder Strap Option Shoulder strap Label Supply door Loading MediaRoll of supplies Supply holder tabs Release button Paper exit chute Loading Die-cut Labels Peel off enablers Peel rollerPeel roller Peeler bar Tear edge for liner Liner Roll of label Supply holder tabs Release buttonPaper core Label Liner Loading Fan-fold LabelsPaper guides Fan-fold paper entrance chute Fan-fold mediaHinged Cable door Screws Connecting the Communication CableRS232 port RS232 port Cable cavity Null modem cableHinged cable door Bluetooth Using the Bluetooth Wireless OptionalBattery Power Charging the BatteryStatus LED Power LED Description Status LEDPage LCD Display and Buttons Using the Display and ButtonsNavigation buttons LCD display On/Off button Icon DescriptionLCD Display Icon Description Option LCD/Keyboard OperationSWI LCD Menu OverviewPause Setup File ManagerMain Menu Speed SetupSpeed Ips Direction DensityDensity DirectionPrint Mode Tear Off Mode/Batch Mode/Peeler Mode Batch Mode Peeler ModeOffset Reference X & Reference Y001 002 850Auto Gap Manual Gap Gap Sensor Bline SensorGap Sensor Auto GapCalibrating Stock AD = Insert liner Then hit EnterGAP Calibrate Manual Gap Gap Sensor Stock AD = Intension =Insert label Then hit Enter Auto Bline Manual BlineBline Calibrate Black SensorContinuous Manual BlineCalibrate None Odd Calibrate 1009600 bps 19200 bps One Stop Bit Two Stop Bits 8 Data Bits ExitVersion 1.2 M23 WiFi TSC Wireless Status Configure00A0F8E2AD9E Protocol TCP State Unknow Radio Ieee 802.11b IP Address Subnet MaskGateway 000.000.000.000 IP Address 000.000.000.000Subnet Mask 000.000.000.000 Port +09100 PSP3Protocol SsidReset Save Settings? Are you sure?Escape Char +035 Escape CharChange PIN 0000 Disable ExitSecurity Change PINContract Local Name BT23Local Name InformationDisable 10 Seconds Disable EnableLow Power BacklightShut Down Disable 5 MinutesFile Manager Dram 256 KB Free FLASH3072 KB Free To print out the self test data to a label DiagnosticsBattery Voltage = 7.33 Display Display Buttons English Exit LanguageDefault setting ServiceInitialization Mileage Info ParameterMileage 6m Labels 53pcs Connect with a Cable to Print Printing LabelsConnect by Radio Optional ReadyBefore Stand-along Download the Format Stand-along PrintingRF Network Problem No Power Not Printing No Paper Possible Cause TroubleshootingRecovery Procedure Start Stand-along PrintingPaper Jam Reduced Battery lifePoor Print Quality Printer Part Print Head Platen Roller Peel Roller Method MaintenanceInterval Tear Bar/Peel Bar Sensor Exterior InteriorIllustration for recommended cleaning parts Page Update Firmware Via Serial Port Firmware Update ProcedurePage Page Update Firmware Via USB Port Printer initialization Power on utilitiesInitializing Ignore AUTO.BAS Ignore AUTO.BASPage No.35, Sec , Ligong 1st Rd., Wujie Township