The Speaker Company M23 user manual Label Liner Loading Fan-fold Labels, Paper core

Page 15

5.Close the supply door.

6.Press the button once or twice to advance the labels until the liner is separates from the label.

Label

Liner

2.3.3 Loading Fan-fold Labels

1.Open the supply door by pulling outward on the release buttons on both sides of the printer.

2.Pull supply holder tabs apart to insert a 3” paper core to keep supply holder wide open.

3” Paper core

3.Insert the fan-fold paper through the fan-fold paper entrance chute and pass over the paper exit chute.

Image 15

Contents USER’S Manual Contents Printer initialization Ignore AUTO.BAS Update Firmware Via Serial Port Update Firmware Via USB PortCopyright Declaration CompliancesWichtige Sicherheits-Hinweise Unpacking and Inspection Equipment ChecklistIntroduction DocumentationTear plate for label Peel roller Tear bar for liner Peel bar Front ViewPage Rear View Supply door Release button Install the BatteryLi-ion battery Release button Getting StartedHand strap Strap button Rings Using the StrapShoulder Strap Option Shoulder strap Loading Media Roll of supplies Supply holder tabs Release buttonLabel Supply door Paper exit chute Loading Die-cut Labels Peel off enablers Peel rollerPeel roller Peeler bar Tear edge for liner Liner Roll of label Supply holder tabs Release buttonPaper core Label Liner Loading Fan-fold LabelsPaper guides Fan-fold paper entrance chute Fan-fold mediaRS232 port Cable cavity Null modem cable Connecting the Communication CableHinged Cable door Screws RS232 portHinged cable door Bluetooth Using the Bluetooth Wireless OptionalStatus LED Charging the BatteryBattery Power Status LED Power LED DescriptionPage Icon Description Using the Display and ButtonsLCD Display and Buttons Navigation buttons LCD display On/Off buttonLCD Display Icon Description Option LCD/Keyboard OperationSWI LCD Menu OverviewSetup File Manager Main MenuPause Setup Speed IpsSpeed Direction DensityDirection DensityReference X & Reference Y Batch Mode Peeler ModePrint Mode Tear Off Mode/Batch Mode/Peeler Mode Offset001 002 850Auto Gap Gap Sensor Bline SensorAuto Gap Manual Gap Gap SensorInsert liner Then hit Enter GAP CalibrateCalibrating Stock AD = Manual Gap Gap Sensor Stock AD = Intension =Black Sensor Auto Bline Manual BlineInsert label Then hit Enter Bline CalibrateContinuous Manual BlineCalibrate Calibrate 100 9600 bps 19200 bpsNone Odd One Stop Bit Two Stop Bits 8 Data Bits ExitIP Address Subnet Mask Status ConfigureVersion 1.2 M23 WiFi TSC Wireless 00A0F8E2AD9E Protocol TCP State Unknow Radio Ieee 802.11bIP Address 000.000.000.000 Subnet Mask 000.000.000.000Gateway 000.000.000.000 Ssid PSP3Port +09100 ProtocolEscape Char Save Settings? Are you sure?Reset Escape Char +035Change PIN Disable ExitChange PIN 0000 SecurityInformation Local Name BT23Contract Local NameBacklight Disable EnableDisable 10 Seconds Low PowerDisable 5 Minutes File ManagerShut Down Dram 256 KB Free FLASH3072 KB Free To print out the self test data to a label DiagnosticsBattery Voltage = 7.33 Display Display Buttons English Exit LanguageParameter ServiceDefault setting Initialization Mileage InfoMileage 6m Labels 53pcs Ready Printing LabelsConnect with a Cable to Print Connect by Radio OptionalStand-along Printing RF NetworkBefore Stand-along Download the Format Start Stand-along Printing TroubleshootingProblem No Power Not Printing No Paper Possible Cause Recovery ProcedureReduced Battery life Poor Print QualityPaper Jam Tear Bar/Peel Bar Sensor Exterior Interior MaintenancePrinter Part Print Head Platen Roller Peel Roller Method IntervalIllustration for recommended cleaning parts Page Update Firmware Via Serial Port Firmware Update ProcedurePage Page Update Firmware Via USB Port Printer initialization Power on utilitiesInitializing Ignore AUTO.BAS Ignore AUTO.BASPage No.35, Sec , Ligong 1st Rd., Wujie Township