The Speaker Company M23 Copyright Declaration, Compliances, Wichtige Sicherheits-Hinweise

Page 4

Copyright Declaration

Information in this manual is subject to change without notice and does not represent a commitment on the part of TSC Auto ID Technology Co., Ltd.. No part of this manual may be reproduced or transmitted in any form by any means, for any purpose other than the purchaser’s personal use, without the expressed written permission of TSC Auto ID Technology Co., Ltd..

The TrueType font engine is developed from the “FreeType Project" by David Turner, Robert Wilhelm, and Werner Lemberg. All other products referred on this document are the trademark or the registered trademark of each belonged companies.

Compliances

CE Class B:

EN55022:1998+A1:2000+A2:2003:

EN55024:1998+A1:2001+A2:2003:

EN 61000-4 SERIES REQULATIONS

ETSI EN 301 489-17:V1.2.1(2002-08)

FCC:

CFR 47, Part 15/CISPR 22 3RD EDITION:1997, Class B

ANSI C63.4:2003

CANADIAN ICES-003

C-Tick:

AS/NZS CISPR22 (Class B)

UL, CUL

UL 60950 3rd

TÜ V/Safety:

EN60950: 2000

Wichtige Sicherheits-Hinweise

1.Bitte lesen Sie diese Hinweis sorgfältig durch.

2.Heben Sie diese Anleitung fűr den späteren Gebrauch auf.

3.Vor jedem Reinigen ist das Gerät vom Stromentz zu trennen. Verwenden Sie keine Flüssig-oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung.

4.Die Netzanschluß -Steckdose soll nahe dem Gerät angebracht und leicht zugänglich sein.

5.Das Gerät ist vor Feuchtigkeit zu schűtzen.

6.Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Beschädigungen hervorrufen.

7.Beachten Sie beim Anschluß ans Stromnetz die Anschluß werte.

8.8. Dieses Gerät kann bis zu einer Außentemperatur von maximal 40betrieben werden.

1

Image 4
Contents USER’S Manual Contents Update Firmware Via Serial Port Update Firmware Via USB Port Printer initialization Ignore AUTO.BASCompliances Copyright DeclarationWichtige Sicherheits-Hinweise Equipment Checklist IntroductionDocumentation Unpacking and InspectionFront View Tear plate for label Peel roller Tear bar for liner Peel barPage Rear View Install the Battery Li-ion battery Release buttonGetting Started Supply door Release buttonUsing the Strap Hand strap Strap button RingsShoulder Strap Option Shoulder strap Roll of supplies Supply holder tabs Release button Loading MediaLabel Supply door Peel off enablers Peel roller Paper exit chute Loading Die-cut LabelsRoll of label Supply holder tabs Release button Peel roller Peeler bar Tear edge for liner LinerLabel Liner Loading Fan-fold Labels Paper coreFan-fold paper entrance chute Fan-fold media Paper guidesConnecting the Communication Cable Hinged Cable door ScrewsRS232 port RS232 port Cable cavity Null modem cableUsing the Bluetooth Wireless Optional Hinged cable door BluetoothCharging the Battery Battery PowerStatus LED Power LED Description Status LEDPage Using the Display and Buttons LCD Display and ButtonsNavigation buttons LCD display On/Off button Icon DescriptionLCD Display Icon Description LCD/Keyboard Operation OptionLCD Menu Overview SWIMain Menu Setup File ManagerPause Speed Ips SetupSpeed Density DirectionDensity DirectionBatch Mode Peeler Mode Print Mode Tear Off Mode/Batch Mode/Peeler ModeOffset Reference X & Reference Y850 001 002Gap Sensor Bline Sensor Auto Gap Manual GapGap Sensor Auto GapGAP Calibrate Insert liner Then hit EnterCalibrating Stock AD = Gap Sensor Stock AD = Intension = Manual GapAuto Bline Manual Bline Insert label Then hit EnterBline Calibrate Black SensorManual Bline ContinuousCalibrate 9600 bps 19200 bps Calibrate 100None Odd 8 Data Bits Exit One Stop Bit Two Stop BitsStatus Configure Version 1.2 M23 WiFi TSC Wireless00A0F8E2AD9E Protocol TCP State Unknow Radio Ieee 802.11b IP Address Subnet MaskSubnet Mask 000.000.000.000 IP Address 000.000.000.000Gateway 000.000.000.000 PSP3 Port +09100Protocol SsidSave Settings? Are you sure? ResetEscape Char +035 Escape CharDisable Exit Change PIN 0000Security Change PINLocal Name BT23 ContractLocal Name InformationDisable Enable Disable 10 SecondsLow Power BacklightFile Manager Disable 5 MinutesShut Down Dram 256 KB Free FLASH3072 KB Free Diagnostics To print out the self test data to a labelBattery Voltage = 7.33 Display Display Buttons Language English ExitService Default settingInitialization Mileage Info ParameterMileage 6m Labels 53pcs Printing Labels Connect with a Cable to PrintConnect by Radio Optional ReadyRF Network Stand-along PrintingBefore Stand-along Download the Format Troubleshooting Problem No Power Not Printing No Paper Possible CauseRecovery Procedure Start Stand-along PrintingPoor Print Quality Reduced Battery lifePaper Jam Maintenance Printer Part Print Head Platen Roller Peel Roller MethodInterval Tear Bar/Peel Bar Sensor Exterior InteriorIllustration for recommended cleaning parts Page Firmware Update Procedure Update Firmware Via Serial PortPage Page Update Firmware Via USB Port Power on utilities Printer initializationInitializing Ignore AUTO.BAS Ignore AUTO.BASPage No.35, Sec , Ligong 1st Rd., Wujie Township