Telenetics CDMA Attaching Mounting Feet stand-alone Omega Cdma Modem, Power Supply Connections

Page 12

AT Commands

IMPORTANT! Before you program the phone number and the system ID into the transceiver, use the default pass code to unlock the transceiver: AT~NAMLCK=000000, followed by AT~NAMVAL=nam, num, sid, nid <CR>

After you obtain CDMA service, use the LEDs on the OMEGA CDMA Modem to verify the modem’s RSSI (see “LEDs” on page 17).

Attaching Mounting Feet (stand-alone OMEGA CDMA Modem)

The stand-alone OMEGA CDMA Modem comes with a Mounting Feet Kit that allows flexible mounting options for the OMEGA CDMA Modem. To use the mounting feet, align the hole on each mounting foot with the mounting hole on the OMEGA CDMA Modem and secure with a screw. Then use the hole on the other end of the mounting foot to secure the OMEGA to the appropriate surface.

Installing the Optional 8-Port RS-232 Module

If you purchased the optional 8-port RS-232 module, refer to Appendix B for instructions on installing the module in the OMEGA CDMA Modem.

Power Supply Connections

Note: If the Marwell socket adapter option has been purchased from Telenetics, skip this section.

For OMEGA CDMA Modems equipped with an AC power connector, connect the OMEGA CDMA Modem to a single phase AC source in the range of 90 VAC to 277 VAC, at 50 or 60 Hz. Use a UL-listed and approved power cord, with a rating of 10 amps or above and a maximum wire size of 16 AWG. Figure 1-1 on page 7 and Figure 1-2 on page 8 show the location of the OMEGA CDMA Modem power connector. Table 2-1 lists the AC power connector reference information.

For OMEGA CDMA Modems equipped with the DC low-voltage power supply option, a 3.3 VDC power source is necessary.

Page 12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Omega Cdma Modem User’s Guide Important Notice FCC Radiation Exposure Statement FCC ID N7NSB555FCC Part 15 EMI Statement Contents Chapter Introduction ModelsFeatures OptionsIntroduction Hardware Features InstallationType II Omega Cdma Modem Type II Omega Cdma Modem with Marwell Socket Adapter Chapter Installation Installation SummaryObtaining Cellular Telephone Service AT CommandsUnpacking Your Hardware Items Supplied by the UserInstalling the Optional 8-Port RS-232 Module Power Supply ConnectionsAttaching Mounting Feet stand-alone Omega Cdma Modem Setting the Omega DIP Switch Omega Cdma Modem Switch Settings DescriptionDTR Dial Enable AT Commands DTE Baud Rate Switch Baud Rate bpsAttaching a DTE Cable OFFDCD OUT RTS TXD CTS RXD TX+ OUT RX+Powering-up the Modem Call Answer TestingConfiguring the Omega Cdma Modem LEDs Indicating Modem Control Signals SW5 on DTE SignalLEDs LEDs Indicating Rssi SW5 OFFChapter Troubleshooting Problem SolutionAppendix a AT Commands Table A-1. Basic AT Commands Parameter Description CommandString default is 2 seconds Table A-3. Basic Action Commands Parameter DescriptionReset CLIENT=CLIENT? DTRAT Command Parameter Description ~NAMLCK ~NAMVAL?0~NAMVAL= Write Account Activation DataAT Command Line Syntax Table A-6. Telenetics-Proprietary CommandsResult Codes Using S-Registers AT Commands Table A-7. Result Codes Number Word DescriptionOnly until the next reset or power off Page Appendix B Installing the 8-port RS-232 Module Verifying Package ContentsInstallation Installing the 8-port RS-232 Module Eight-Port Module PortsLimited Product Warranty Return Merchandise Authorization RMA Procedure
Top Page Image Contents