CPU Configuration

Taylor CONROE1333-DVI/H user manual CPU Configuration

Page 30

BIOS SETUP UTILITY

Main

Advanced

H/W Monitor

Boot

Security

Exit

Advanced Settings

WARNING : Setting wrong values in below sections may cause system to malfunction.

Chipset Configuration

ACPI Configuration

IDE Configuration

PCIPnP Configuration

Floppy Configuration

SuperIO Configuration

USB Configuration

Configure CPU

	Select Screen
	Select Item
Enter	Go to Sub Screen
F1	General Help
F9	Load Defaults
F10	Save and Exit
ESC	Exit

Setting wrong values in this section may cause the system to malfunction.

3.3.1 CPU Configuration

BIOS SETUP UTILITY

Advanced

CPU Configuration

Overclock Mode	[Auto]
CPU Frequency (MHz)	[133]
PCIE Frequency (MHz)	[100]
Boot Failure Guard	[Enabled]
Spread Spectrum	[Auto]
Ratio Actual Value	9
Enhance Halt State	[Disabled]
Max CPUID Value Limit	[Disabled]
Intel (R) Virtualization tech.	[Enabled]
CPU Thermal Throttling	[Enabled]
No-Excute Memory Protection	[Disabled]
Hyper Threading Technology	[Enabled]
Intel (R) SpeedStep(tm) tech.	[Auto]

Select the over clock mode.

	Select Screen
	Select Item
+-	Change Option
F1	General Help
F9	Load Defaults
F10	Save and Exit
ESC	Exit

Overclock Mode

Use this to select Overclock Mode. The default value is [Auto]. Cnfiguration options: [Auto], [CPU, PCIE, Sync.] and [CPU, PCIE, Async.].

CPU Frequency (MHz)

Use this option to adjust CPU frequency. The default value is [133].

PCIE Frequency (MHz)

Use this option to adjust PCIE frequency. The default value is [100].

Boot Failure Guard

Enable or disable the feature of Boot Failure Guard.

Spread Spectrum

This item should always be [Auto] for better system stability.

3 0

Image 30

Contents

ConRoe1333-DVI/H Copyright Notice DisclaimerContents Software Support Package Contents IntroductionSpecifications See Caution ConnectorBios Feature Support CDDDRII533*, DDRII667 CPU Motherboard Layout 24.4cm 9.6HD 8CH I/O Table for Audio Output ConnectionPre-installation Precautions Screw HolesCPU Installation Page Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Notch breakInstalling an expansion card Expansion Slots PCI, Hdmr and PCI Express SlotsDVI Graphics-HDCP card DVI Graphics-HDCP Card Installation GuideDVI-D connector DVI-D monitor DVI Graphics-HDCPWhat is HDCP? Hdcp Function with DVI Graphics-HDCP CardJumpers Setup PS2USBPWR1Onboard Headers and Connectors IDE1USB 2.0 Headers Chassis Speaker Header Serial port Header Sataii Hard Disk Setup Guide Western DigitalDriver Installation Guide Hdmr Card and Driver InstallationUntied Overclocking Technology Bios Menu Bar Navigation Keys Main ScreenAdvanced Screen CPU Configuration Ratio Actual Value Ratio Cmos SettingRatio Status Enhance Halt StateIntel R SpeedSteptm tech Chipset ConfigurationConfigure Dram Timing by SPD Dram FrequencyDvmt Mode Select Dram RAS# to CAS# DelayInternal Graphics Mode Select Dram CAS# LatencyFront Panel Control DVMT/FIXED MemoryOnBoard HD Audio CD-InAcpi Configuration IDE Device Configuration IDE ConfigurationATA/IDE Configuration ATA/IDE Configuration EnhancedDMA Mode LBA/Large ModePIO Mode Block Multi-Sector TransferA.R.T PCIPnP ConfigurationPCI Latency Timer Bit Data TransferOnBoard Floppy Controller Floppy ConfigurationSuper IO Configuration Serial Port AddressUSB Configuration CPU Quiet Fan Target CPU Temperature CHardware Health Event Monitoring Screen Tolerance CBoot From Onboard LAN Boot ScreenBoot Settings Configuration Boot Up Num-LockMain Advanced Monitor Boot Change Supervisor PasswordSecurity Screen Save Changes and Exit Load Optimal DefaultsExit Screen Discard Changes and ExitRunning The Support CD Install Operating SystemSupport CD Information Drivers Menu

Taylor CONROE1333-DVI/H user manual CPU Configuration

BIOS SETUP UTILITY