Taylor CONROE1333-DVI/H user manual DDRII533*, DDRII667

Page 8

CAUTION!

1.FSB1333-CPU will operate in overclocking mode. Under this situation, PCIE frequency will also be overclocked to 115MHz.

2.About the setting of “Hyper Threading Technology”, please check page 31.

3.This motherboard supports Untied Overclocking Technology. Please read “Untied Overclocking Technology” on page 27 for details.

4.This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 16 for proper installation.

5.Please check the table below for the CPU FSB frequency and its corre-

sponding memory support frequency.

CPU FSB Frequency

Memory Support Frequency

1333

DDRII533*, DDRII667

1066

DDRII400, DDRII533, DDRII667

800

DDRII400, DDRII533, DDRII667

533DDRII400, DDRII533

*When you use a FSB1333-CPU on this motherboard, it will run at DDRII500 if you adopt a DDRII533 memory module.

6.Due to the chipset limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® XP, Windows® XP 64-bit, Windows® VistaTM and Windows® VistaTM 64-bit.

7.Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU.

8.While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system.

9.The maximum shared memory size is defined by the chipset vendor and is subject to change. Please check Intel® website for the latest information.

10.For microphone input, this motherboard supports both stereo and mono modes. For audio output, this motherboard supports 2-channel, 4-channel, 6-channel, and 8-channel modes. Please check the table on page 11 for proper connection.

11.Before installing SATAII hard disk to SATAII connector, please read the “SATAII Hard Disk Setup Guide” on page 26 to adjust your SATAII hard disk drive to SATAII mode. You can also connect SATA hard disk to SATAII connector directly.

12.Power Management for USB 2.0 works fine under Microsoft® Windows® VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2 / 2000 SP4.

13.Microsoft® Windows® VistaTM / VistaTM 64-bit driver keeps on updating now. As long as we have the latest driver, we will update it to our website in the future. Please visit our website for Microsoft® Windows® VistaTM / VistaTM 64-bit driver and related information.

ASRock website http://www.asrock.com

8

Image 8
Contents ConRoe1333-DVI/H Copyright Notice DisclaimerContents Software Support Package Contents IntroductionSpecifications Connector Bios FeatureSee Caution Support CDDDRII533*, DDRII667 CPU Motherboard Layout 24.4cm 9.6HD 8CH I/O Table for Audio Output ConnectionPre-installation Precautions Screw HolesCPU Installation Page Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Notch breakInstalling an expansion card Expansion Slots PCI, Hdmr and PCI Express SlotsDVI Graphics-HDCP Card Installation Guide DVI-D connector DVI-D monitorDVI Graphics-HDCP card DVI Graphics-HDCPWhat is HDCP? Hdcp Function with DVI Graphics-HDCP CardJumpers Setup PS2USBPWR1Onboard Headers and Connectors IDE1USB 2.0 Headers Chassis Speaker Header Serial port Header Sataii Hard Disk Setup Guide Western DigitalUntied Overclocking Technology Driver Installation GuideHdmr Card and Driver Installation Bios Menu Bar Advanced Screen Navigation KeysMain Screen CPU Configuration Ratio Cmos Setting Ratio StatusRatio Actual Value Enhance Halt StateChipset Configuration Configure Dram Timing by SPDIntel R SpeedSteptm tech Dram FrequencyDram RAS# to CAS# Delay Internal Graphics Mode SelectDvmt Mode Select Dram CAS# LatencyDVMT/FIXED Memory OnBoard HD AudioFront Panel Control CD-InAcpi Configuration IDE Configuration ATA/IDE ConfigurationIDE Device Configuration ATA/IDE Configuration EnhancedLBA/Large Mode PIO ModeDMA Mode Block Multi-Sector TransferPCIPnP Configuration PCI Latency TimerA.R.T Bit Data TransferFloppy Configuration Super IO ConfigurationOnBoard Floppy Controller Serial Port AddressUSB Configuration Target CPU Temperature C Hardware Health Event Monitoring ScreenCPU Quiet Fan Tolerance CBoot Screen Boot Settings ConfigurationBoot From Onboard LAN Boot Up Num-LockSecurity Screen Main Advanced Monitor BootChange Supervisor Password Load Optimal Defaults Exit ScreenSave Changes and Exit Discard Changes and ExitInstall Operating System Support CD InformationRunning The Support CD Drivers Menu