Vista Imaging Vista Routing manual VistARad Configuration-Receiving Sites

Page 56

Configuring Routing

Routing User Guide

 

 

receiving sites (see the next section for details). It is recommended that the SITE CODE be set to your standard 3-digit site code.

Select OPTION: E ENTER OR EDIT FILE ENTRIES

INPUT TO WHAT FILE: 2006.1 IMAGING SITE PARAMETERS (1 entry)

EDIT WHICH FIELD: ALL// .09 SITE CODE

THEN EDIT FIELD: <enter>

Select IMAGING SITE PARAMETERS NAME: `1 TEST SITE

SITE CODE: TST

VistARad Configuration—Receiving Sites

VistARad workstations at receiving sites will need to be configured to check the appropriate local storage location for the presence of routed exams. This is done by setting the CacheLocationID in the MAGJ.INI file for each VistARad workstation.

Setting the CacheLocationID affects VistARad in the following ways:

ƒWhen a user logs into VistARad, the locally-defined CacheLocationID is compared to the SITE CODE (IMAGING SITE PARAMETERS File (#2006.1)) of the site being logged into. If the two values are different, the VistARad software assumes that it will be used to display routed images.

ƒWhen a routed exam is selected for display, VistARad will check the local storage location for routed images. The storage location checked is specified in the applicable NETWORK LOCATION File (#2005.2) entry at the sending site.

The following steps must be performed for each VistARad workstation that will be used to display routed images.

To set the CacheLocationID in MAGJ.INI

1Log into the VistARad workstation as an administrator.

2Use Explorer or the Start Run menu option to open

C:\Programs\Vista\ImagingMAG_VistaRad\MAGJ.INI.

3Locate the CacheLocationID line under [Workstation Settings], near the beginning of the file.

4For CacheLocationID, enter the destination name that contains local copies of routed images.

ÂThe value you enter must match a routing destination name as defined in the sending site’s NETWORK LOCATION File.

48

VistA Imaging V. 3.0, Patch 18

April 2006

Image 56
Contents Routing User Guide-DRAFT April VistA Imaging V .0, Patch Contents Troubleshooting Routing Introduction Terms of UseUsing this Manual About this ManualConventions AcknowledgementsDate Rev Related DocumentsRevision Table This page is intentionally blank Routing Overview Routing ExplainedInfrastructure Requirements What is a Routing Gateway?Routing Prerequisites Operational Requirements How Autorouting Works Identifying Images to be AutoroutedAutorouting Images from Prior Exams Sending Images to DestinationsDeletion of Routed Images Remote Reading with VistARadRouting Overview How On-Demand Routing Works Selecting Images for On-Demand RoutingHow Routing Priority Works Priority and AutoroutingPriority and On-demand Routing Other Priority FactorsHow Routing Rules Work Defining Routing RulesRouting Rules Explained Simple Routing Rule Rules using Multiple ConditionsSample Routing Rules Rules using Date/Time Conditions Rules using WildcardsRules using the does not match Operator Rule Destinations Send CommandBalance Command Resetting the Load Balancing Counter How Load Balancing WorksFrequently Used Properties Rule ConditionsProperties NOW Network storage location of the image abstract Other PropertiesPath for the network location of the stored image Unique 26-character image identifier of the Pacs image Name of the Radiology Report associated with the image Operator Image property must… OperatorsValues Send CR images to Kansas on Holidays Values for Date/Time PropertiesSend CR images to Kansas on Mon/Wed/Fri Routing Rule Priority Routing Images from Prior ExamsPrioritize images based on destination Do or Do Not include Prior StudiesRouting Rule Tips This page is intentionally blank Configuring Routing Configuration Task Performed ByField Description Defining Imaging DestinationsNaming Conventions for Imaging Destinations Network Location File Entries at Jonesville Storage Location Names for offsite MRI specialistFolder Creation Storage Folders for Imaging DestinationsFolder Prerequisites Testing folders from the sending site Explorer Folder VerificationTesting folders from the sending site Command Line Editing the Network Location File at the sending site Imaging Destination Definition using FileManImaging Destination Definition Imaging Destination Values Physical Reference Do not use This field is not used for routing, and should be left blank Retention Period Defining Dicom Destinations Naming Conventions for Dicom DestinationsDicom Destination Definitions in SCUList.dic Adding Dicom Destinations to SCUList.dicMagdmenu Field Definitions Verifying that Prefetch is Enabled Defining Route Priors LogicHow Prior Exam Routing Works Altering Route Priors LogicTo change route priors logic Select the following fields for editingTo configure Image Gateways Dicom Gateway ConfigurationImage Gateway Configuration Routing Gateway Configuration To configure the Routing GatewayTo create and import routing rules Importing Routing Rules Route.dicCreating and Importing a Routing Rules File Verifying Imported Rules To verify imported rulesRe-Importing Routing Rules Routing Rules & Multiple Routing GatewaysVistARad Configuration-Sending Sites To set routing-related VistARad site parametersVistARad Configuration-Receiving Sites To set the CacheLocationID in MAGJ.INIMaking Multiple Destinations Accessible to VistARad Changes Affecting Routing System Configuration Routing System Change Related Configuration ChangeStarting the Evaluation Processor Using the Routing GatewayActivating Routing Starting the Transmission Processor Periodic Maintenance Using Routing Log FilesMaintaining Routing Displaying log filesLong-Term Routing Shutdown Disabling RoutingShort-Term Routing Shutdown Stop the Transmission Processor Routing Gateway Menu OptionsStart the Transmission Processor Start the Evaluation Processor Stop the Evaluation ProcessorImport Routing Rules Purge all completed entries in the Transmission QueueDisplay Current Set of Routing Rules Re-Queue all failed entries in the Transmission QueueRemove obsolete entries from Transmission Queue This page is intentionally blank Using VistARad in a Routing System Displaying Routed ExamsTo display a routed exam On-Demand Routing Requirements Using On-Demand RoutingVistARad & On-Demand Routing To use on-demand routing Routing User Guide This page is intentionally blank Troubleshooting Routing Basic TroubleshootingGetting Help If… Then…Additional Routing Considerations Transmission Processors and Drive MappingFactors Affecting Routing Speed Routed Images vs. Routed ExamsHow the RC Column is Populated Preventing Transmission of Duplicate ExamsThis page is intentionally blank Appendix a Appendix a Imaging Destination Worksheet Specified in sending site’s Network Location fileNetwork Location File Sample For detailed information about specific fields, seeDicom Destination Worksheet Dicom Destination SampleRouting Rule Definition Worksheet Routing User Guide Sample Rules Example #1Example #2 Example #3Example #4 Example #5Example #6 Example #7Routing Setup Checklist Appendix B Using MAGDecompressor MAGDecompressor SetupInstallation LicensingCd \Program Files\VistA\Imaging\MAGDecompressor Enter MAGDecompressor Logging Sample log entrySelected log file error codes Glossary Glossary Glossary This page is intentionally blank See also routing Background Processor 32 balance command IndexSee also routing operators, routing rule 11, 20 passwords 28 Index