XiNCOM manual Configuring the XC-DPG603 for your LAN

Page 11

Configuring the XC-DPG603 for your LAN

Figure 3. LAN & DHCP

Ensure these settings are suitable for your LAN:

•The default settings are suitable for many situations.

•See the following table for details of each setting.

This is the IP address for the XC-DPG603 when seen from the local LAN. Use the defualt value unless the address is already in use or your LAN is using a different IP addres range. In the latter case, enter an unused IP Address from within the range used by you LAN

DPG603 is attached (the same value as the PCs on that LAN segment).

DHCP Server Setup - If Enabled, the XC-DPG603 will allocate IP Addresses to PCs (DHCP clients) on your LAN when they start up. The default and

provide the IP address of the XC-DPG603 as the Default Gateway.

Image 11

Contents Twin WAN DNS IP VPN Gateway Table of Contents QoS Conﬁguration VPN Conﬁguration Use TWO ISPs for expanded bandwidth and redundancy IntroductionFeatures Dhcp Server Support Easy SetupPassword Protected Conﬁguration Http Firmware Upgrade and backupSystem Physical DetailsLED Action Condition Default SettingsOverview Procedure Basic SetupNo Response? Configuring the XC-DPG603 for your LANProcedure Configuring the XC-DPG603 for your LAN Installation Diagram for XC-DPG603 Connecting two broadband modemsAddress Info Configuring for Internet AccessSettings Primary Setup Connection Mode Connection TypeOverview Configure PCs on your LANTCP/IP Settings Internet AccessTo act as a Dhcp Client recommended For Apple ClientsFor Linux Clients Fixed IP AddressAdvanced Port Port Options Health Check Auto Dialup Bridge ModeLoad Balance Settings Load BalanceAdvanced PPPoE Settings Advanced PPPoEAdvanced Pptp Settings Advanced PptpAdvanced Setup Host IP Host IPVirtual Servers Settings Virtual ServerVirtual Servers Server List Settings Custom Virtual ServersCustom Virtual Servers Custom Virtual ServersSpecial Application Settings Special ApplicationsSpecial Applications Dynamic DNS To use the Dynamic DNS FeatureSettings Dynamic DNS Dynamic DNSPrivate IP Address Multi DMZ & UPnPFor Dynamic IP Select the desired WAN portSettings Advanced Features Advanced FeaturesAdvanced Features HTTP// Internet IP Address of the XC-DPG603 Using Remote Web-based SetupFirewall Exception Security ManagementBlock URL Access FilterSettings Block URL Settings Access FilterSession Limit Settings Session LimitSession Limit & Firewall Exception QoS Conﬁguration How it works VPN ConﬁgurationIPSec Global Setting IPSec Global SettingsVPN Policy Setup Policy SetupKey Management DNS Conﬁguration XC-DPG602 & 603 Gateways How it worksDomain Name Configuration Preference 1 NS Record Primary/Secondary Name ServerPublic WAN 1 & 2 IP Address MX Record Mail ExchangeHost URL List Map Host URLRecord Cname RecordTrap Targets Management AssistantSystem Information Message Status Management AssistantSyslog Conﬁguration To save the XC-DPG603 Conﬁguration to a ﬁle Using the Tftp Utility RecommendedUpdating the Firmware Backup your conﬁguration Restoring Saved Conﬁguration Http Upgrade FirmwareUploading the Firmware To upload the ﬁrmware to the GatewaySystem Status Operation & StatusOperation & Status Existing Dhcp Server Advanced LAN ConﬁgurationStatic Routing Advanced LAN Configuration192.168.1.100 Conﬁguring other Routers on you LAN192.168.2.0 255.255.255.0External Power Adapter DimensionsOperating Temperature Storage TemperatureUsing Specify an IP Address TCP/IP SettingsChecking TCP/IP Settings Windows 9x/ME Using DhcpUsing a ﬁxed IP Address Use the following IP Address Checking TCP/IP Settings WindowsFigure G. Network Conﬁguration Windows XP Checking TCP/IP Settings Windows XPOverview Troubleshooting