X-Micro Tech XWL-11GRTX user manual Wan

Page 13

Antenna

Reset

WAN LAN Power

Interfaces

Description

1. Antenna

The Wireless LAN Antenna.

2.

WAN

The RJ-45 socket allows WAN connection through a

 

 

Category 5 cable. Support auto-sensing on 10/100M

 

 

speed and half/ full duplex; comply with IEEE 802.3/

 

 

802.3u respectively.

3.

LAN

The RJ-45 sockets allow LAN connection through

 

 

Category 5 cables. Support auto-sensing on 10/100M

 

 

speed and half/ full duplex; comply with IEEE 802.3/

 

 

802.3u respectively.

4.

Power

The power jack allows an external DC +7.5 V power

 

 

supply connection.

 

 

The external AC to DC adaptor provide adaptive power

 

 

requirement to the X-Micro WLAN 11g Broadband

 

 

Router.

5.

Reset

Push continually the reset button 5 ~ 10 seconds to reset

 

 

the configuration parameters to factory defaults.

4

Image 13
Contents Wlan 11g Broadband Router MAX. OUT Power Federal Communications Commission FCC Statement Disclaimer CopyrightTable of Contents Frequently Asked Questions FAQ What is WMM? What is Wlan ACK TIMOUT? Terminology VPN 2Product Specifications 1Package contentsGeneric Router Product FeaturesWlan LED Panel DescriptionWAN 2Software Installation 1Hardware InstallationFor OS of Microsoft Windows 2000, XP For OS of Microsoft Windows 95/ 98/ MeFor OS of Microsoft Windows NT Connect to the X-Micro Wlan 11g Broadband RouterItemDescription Bssid Operation Mode Setup WizardIII LAN Interface Setup II Time Zone SettingWireless Basic Settings IV WAN Interface SetupDescription VI Wireless Security SetupWireless Basic Settings MAC address. Client Mode only Wireless Advanced SettingsSystem, Shared Key or Auto selection Wlan IC of Realtek Wireless Security SetupOnly Characters. WPA, PersonalPre-Shared KeyWEP Key Setup Click the Disabled , Allow Listed or Deny Listed Wireless Access ControlWDS Settings II WDS AP Table WDS Security SetupWEP64bits, WEP128bits, Wpatkip WPA2AES or NoneSite Survey LAN Interface Setup Information. Server mode only WAN Interface SetupClick to open the Active Dhcp Client Table window Static IP II Dhcp Client Server There are Continuous , Connect on Demand III PPPoEIf you select the PPPoE and Connect on Demand IV Pptp Firewall Port Filtering Firewall IP Filtering Firewall MAC Filtering Firewall Port Forwarding Screen snapshot Firewall Port Forwarding Firewall DMZ Firewall URL FilteringEnable DMZ Click to enable the DMZ function VPN SettingScreen snapshot VPN Setup VPN Setup Edit Tunnel Mode only Click to select DH1modp768 , DH2modp1024 or II Advanced IKE SetupSent Packets Management StatisticsReceived Packets Management Ddns Management Time Zone SettingManagement Denial-of-Service Management Log Management Upgrade Firmware Management Save/ Reload Settings Management WatchDog Management Password SetupManagement Quality of Service Screen snapshot Management Qaulity of Service Bandwidth Control Table LogoutRemoved from the Current Bandwidth Control Addresses Current Bandwidth Control Table2What is Wireless LAN? 1What and how to find my PC’s IP and MAC address?4How does wireless networking work? 3What are ISM bands?6What is ESSID? 5What is BSSID?9What is WEP? 8What are the Open System and Shared Key authentications?What is Fragment Threshold? What is Beacon Interval? What is RTS Request To Send Threshold?What is Ssid Broadcast? What is Preamble Type?What is Wi-Fi Protected Access WPA? What is WPA2?What is Temporal Key Integrity Protocol TKIP? What is 802.1x Authentication?What is Advanced Encryption Standard AES? What is Inter-Access Point Protocol IAPP?What is Clone MAC Address? What is Maximum Transmission Unit MTU Size?What is DDNS? What is NTP Client?What is Wlan ACK TIMOUT? Example One PPPoE on the WAN Configure the LAN interface Configure the WAN interfaceExample Two Fixed IP on the WAN Configure the Wlan interface192.168.2.254 192.168.2.10Configuration Example Two Fixed IP on the WAN Configure the WAN interface Configure the Wlan interface