X-Micro Tech XWL-11GRTX user manual System, Shared Key or Auto selection

Page 25

Screen snapshot – Wireless Advanced Settings

Item	Description
Authentication Type	Click to select the authentication type in Open
	System, Shared Key or Auto selection.
Fragment Threshold	Set the data packet fragmentation threshold, value
	can be written between 256 and 2346 bytes.
	Refer to 4.10 What is Fragment Threshold?
RTS Threshold	Set the RTS Threshold, value can be written
	between 0 and 2347 bytes.
	Refer to 4.11 What is RTS(Request To Send)
	Threshold?
Beacon Interval	Set the Beacon Interval, value can be written
	between 20 and 1024 ms.
	Refer to 4.12 What is Beacon Interval?
Data Rate	Select the transmission data rate from pull-down
	menu. Data rate can be auto-select, 11M, 5.5M, 2M
	or 1Mbps.
Preamble Type	Click to select the Long Preamble or Short
	Preamble support on the wireless data packet
	16

Image 25

Contents Wlan 11g Broadband Router MAX. OUT Power Federal Communications Commission FCC Statement Disclaimer CopyrightTable of Contents Frequently Asked Questions FAQ What is WMM? What is Wlan ACK TIMOUT? Terminology VPN 2Product Specifications 1Package contentsGeneric Router Product FeaturesWlan LED Panel DescriptionWAN 2Software Installation 1Hardware InstallationFor OS of Microsoft Windows 2000, XP For OS of Microsoft Windows 95/ 98/ MeFor OS of Microsoft Windows NT Connect to the X-Micro Wlan 11g Broadband RouterItemDescription Bssid Operation Mode Setup WizardIII LAN Interface Setup II Time Zone SettingWireless Basic Settings IV WAN Interface SetupDescription VI Wireless Security SetupWireless Basic Settings MAC address. Client Mode only Wireless Advanced SettingsSystem, Shared Key or Auto selection Wlan IC of Realtek Wireless Security SetupOnly Characters. WPA, PersonalPre-Shared KeyWEP Key Setup Click the Disabled , Allow Listed or Deny Listed Wireless Access ControlWDS Settings II WDS AP Table WDS Security SetupWEP64bits, WEP128bits, Wpatkip WPA2AES or NoneSite Survey LAN Interface Setup Information. Server mode only WAN Interface SetupClick to open the Active Dhcp Client Table window Static IP II Dhcp Client Server There are Continuous , Connect on Demand III PPPoEIf you select the PPPoE and Connect on Demand IV Pptp Firewall Port Filtering Firewall IP Filtering Firewall MAC Filtering Firewall Port Forwarding Screen snapshot Firewall Port Forwarding Firewall DMZ Firewall URL FilteringEnable DMZ Click to enable the DMZ function VPN SettingScreen snapshot VPN Setup VPN Setup Edit Tunnel Mode only Click to select DH1modp768 , DH2modp1024 or II Advanced IKE SetupSent Packets Management StatisticsReceived Packets Management Ddns Management Time Zone SettingManagement Denial-of-Service Management Log Management Upgrade Firmware Management Save/ Reload Settings Management WatchDog Management Password SetupManagement Quality of Service Screen snapshot Management Qaulity of Service Bandwidth Control Table LogoutRemoved from the Current Bandwidth Control Addresses Current Bandwidth Control Table2What is Wireless LAN? 1What and how to find my PC’s IP and MAC address?4How does wireless networking work? 3What are ISM bands?6What is ESSID? 5What is BSSID?9What is WEP? 8What are the Open System and Shared Key authentications?What is Fragment Threshold? What is Beacon Interval? What is RTS Request To Send Threshold?What is Ssid Broadcast? What is Preamble Type?What is Wi-Fi Protected Access WPA? What is WPA2?What is Temporal Key Integrity Protocol TKIP? What is 802.1x Authentication?What is Advanced Encryption Standard AES? What is Inter-Access Point Protocol IAPP?What is Clone MAC Address? What is Maximum Transmission Unit MTU Size?What is DDNS? What is NTP Client?What is Wlan ACK TIMOUT? Example One PPPoE on the WAN Configure the LAN interface Configure the WAN interfaceExample Two Fixed IP on the WAN Configure the Wlan interface192.168.2.254 192.168.2.10Configuration Example Two Fixed IP on the WAN Configure the WAN interface Configure the Wlan interface