X-Micro Tech XWL-11GRTX user manual Connect to the X-Micro Wlan 11g Broadband Router

Page 16

2.Move mouse and double-click the right button on Network and Dial-up Connections icon. Move mouse and double-click the Local Area Connection icon. The Local Area Connection window will appear. Click Properties button in the Local Area Connection window.

3.Check the installed list of Network Components. If TCP/IP is not installed, click the Add button to install it; otherwise go to step 6.

4.Select Protocol in the Network Component Type dialog box and click Add button.

5.Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation.

6.Select TCP/IP and click the properties button on the Network dialog box.

7.Select Specify an IP address and type in values as following example.

9IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is good to connect the Wireless LAN Access Point.

9IP Subnet Mask: 255.255.255.0

8.Click OK to completes the IP parameters setting.

For OS of Microsoft Windows NT:

1.Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.

2.Move mouse and double-click the right button on Network icon. The Network window will appear. Click Protocol tab from the Network window.

3.Check the installed list of Network Protocol window. If TCP/IP is not installed, click the Add button to install it; otherwise go to step 6.

4.Select Protocol in the Network Component Type dialog box and click Add button.

5.Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation.

6.Select TCP/IP and click the properties button on the Network dialog box.

7.Select Specify an IP address and type in values as following example.

9IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is good to connect the Wireless LAN Access Point.

9IP Subnet Mask: 255.255.255.0

8.Click OK to complete the IP parameters setting.

3.2Connect to the X-Micro WLAN 11g Broadband Router

Open a WEB browser, i.e. Microsoft Internet Explore, then enter 192.168.1.254

7

Image 16

Contents Wlan 11g Broadband Router MAX. OUT Power Federal Communications Commission FCC Statement Copyright DisclaimerTable of Contents Frequently Asked Questions FAQ What is WMM? What is Wlan ACK TIMOUT? Terminology VPN 1Package contents 2Product SpecificationsProduct Features Generic RouterPanel Description Wlan LEDWAN 1Hardware Installation 2Software InstallationFor OS of Microsoft Windows 95/ 98/ Me For OS of Microsoft Windows 2000, XPConnect to the X-Micro Wlan 11g Broadband Router For OS of Microsoft Windows NTItemDescription Bssid Setup Wizard Operation ModeII Time Zone Setting III LAN Interface SetupIV WAN Interface Setup Wireless Basic SettingsVI Wireless Security Setup DescriptionWireless Basic Settings Wireless Advanced Settings MAC address. Client Mode onlySystem, Shared Key or Auto selection Wireless Security Setup Wlan IC of RealtekCharacters. WPA, PersonalPre-Shared Key OnlyWEP Key Setup Wireless Access Control Click the Disabled , Allow Listed or Deny ListedWDS Settings WDS Security Setup II WDS AP TableWEP64bits, WEP128bits, Wpatkip WPA2AES or NoneSite Survey LAN Interface Setup Information. Server mode only WAN Interface SetupClick to open the Active Dhcp Client Table window Static IP II Dhcp Client Server III PPPoE There are Continuous , Connect on DemandIf you select the PPPoE and Connect on Demand IV Pptp Firewall Port Filtering Firewall IP Filtering Firewall MAC Filtering Firewall Port Forwarding Screen snapshot Firewall Port Forwarding Firewall URL Filtering Firewall DMZVPN Setting Enable DMZ Click to enable the DMZ functionScreen snapshot VPN Setup VPN Setup Edit Tunnel Mode only II Advanced IKE Setup Click to select DH1modp768 , DH2modp1024 orSent Packets Management StatisticsReceived Packets Management Time Zone Setting Management DdnsManagement Denial-of-Service Management Log Management Upgrade Firmware Management Save/ Reload Settings Management Password Setup Management WatchDogManagement Quality of Service Screen snapshot Management Qaulity of Service Logout Bandwidth Control TableRemoved from the Current Bandwidth Control Addresses Current Bandwidth Control Table1What and how to find my PC’s IP and MAC address? 2What is Wireless LAN?4How does wireless networking work? 3What are ISM bands?5What is BSSID? 6What is ESSID?9What is WEP? 8What are the Open System and Shared Key authentications?What is Fragment Threshold? What is RTS Request To Send Threshold? What is Beacon Interval?What is Preamble Type? What is Ssid Broadcast?What is Wi-Fi Protected Access WPA? What is WPA2?What is 802.1x Authentication? What is Temporal Key Integrity Protocol TKIP?What is Advanced Encryption Standard AES? What is Inter-Access Point Protocol IAPP?What is Maximum Transmission Unit MTU Size? What is Clone MAC Address?What is DDNS? What is NTP Client?What is Wlan ACK TIMOUT? Example One PPPoE on the WAN Configure the WAN interface Configure the LAN interfaceConfigure the Wlan interface Example Two Fixed IP on the WAN192.168.2.254 192.168.2.10Configuration Example Two Fixed IP on the WAN Configure the WAN interface Configure the Wlan interface