Vox AD10VT, AD30VT, AD50VT, AD15VT Effect Section, TREBLE, MIDDLE, and Bass, Master, Effects, Edit

Page 10

TREBLE, MIDDLE, and BASS

This trio of knobs allow you to dial in the exact amount of high, mid, and low fre- quencies. Also, as you’d expect (and hope!), the exact manner in which each one of these controls behaves and also interacts with the others is dependant on the amp model selected. Turn to the “Amp models and effects” section (page 17) for more information.

NOTE: In keeping with the originals, certain models will produce almost no sound if all of these three tone controls are turned all the way down (counter-clockwise).

NOTE: Not all of the original amps that we modeled actually have all three of the Tre- ble, Middle, and Bass controls. In such cases, we allow you to use all three knobs to effectively increase the tonal range of the original. Turn to the “Amp models and effects” section (page 17) for more information.

MASTER

This adjusts the volume that is output from the preamp to the Valve Reactor power amp. This will vary the amount of distortion created by Valve Reactor.

NOTE: The MASTER volume control is NOT programmable.

NOTE: The GAIN control also affects the amount of distortion. For some settings, there may be virtually no distortion.

3.EFFECT SECTION

Here you can make settings for effects and noise reduction. For details on each effect, refer to “Amp models and effects” (page 17).

EFFECTS

Selects the type of effect. You can use the TAP button, EDIT 1 knob and Bypass button to adjust the parameters of each effect. When you select an effect type, the effect parameters will be initialized and Effect Bypass will be defeated.

EDIT 1

Use this to adjust the parameters of each effect. By using this knob in conjunction with the TAP and BYPASS buttons as described below, you can adjust three differ- ent parameters. (That is, if the BYPASS LED is dark.)

•Turn EDIT 1 (without pressing a button) (EDIT 1)

•Turn EDIT 1 while pressing TAP (EDIT 2)

•Turn EDIT 1 while pressing BYPASS (EDIT 3)

If the BYPASS LED is lit (the effect is bypassed), you can hold down the TAP but- ton and turn the EDIT 1 knob simultaneously to adjust the noise reduction sensi- tivity.

NOTE: You can’t adjust the effect parameters while the BYPASS LED is lit.

6

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Page Important Safety Instructions Table of Contents Page Introduction Main FeaturesWelcome Aboard Power AMP and the Glory Signal PathValve Reactor Technology Setup Quick StartSwitching Between the Channels of a Program Checking OUT the Preset ProgramsCreating Your OWN Sounds Input Section VolumeGuitarist’s Guided Panel Tour AMP SectionMaster Effect SectionTREBLE, MIDDLE, and Bass EffectsPRESET/MANUAL/CHANNEL Section Power Level Power SwitchAC power Write buttonSend jack LINE/PHONEExternal Speaker OUT jack Return jackChannel Select Mode Selecting a Channel Program Preset Mode Selecting a Preset ProgramAbout the three operating modes Switching Channels Manual ModeGetting to Manual Mode Creating and storing your own program Creating Your OWN ProgramAdjusting the Noise Reduction When you’ve come up with a sound you like, store the programChecking the Settings of a Program Original Values Storing Your ProgramRestoring the Factory Settings Turn the power offTurning Effect Bypass ON/OFF Switch Using the VFS2 dual foot switchSwitching the Channel Program Switch Switching to Manual Mode SwitchAMP Models Amp models and effectsControlling Factors Tube Talk Power AMP AccuracyTurn IT UP Boutique CL BlackAC15 UK ’70s US Higain UK ModernNumetal Boutique ODEDIT2 EffectsEDIT1 EDIT3Comp TAPFlanger Delay Troubleshooting Amp isn’t powering up when the Power switch is onYou can’t hear any effects Specifications Input/output jacksProgrammer’s Cheat Sheet Program Name EDIT2TAP+EDIT 1 /TAP
Top Page Image Contents