Vox AD15VT, AD30VT, AD50VT, AD10VT manual Switching Channels, Getting to Manual Mode

Page 15

SWITCHING CHANNELS

With either the CH1 or CH2 LED lit, press the CH switch. The channel will change each time you press the button, and the program stored in each channel will be recalled. (The physical settings of the top panel selector knobs and control knobs are ignored at this time.)

HINT: If the optional VFS2 dual foot switch is connected to the rear panel, you can use it to switch programs. For details, refer to “Using the VSF2 dual foot switch” (page 16).

HINT: If you want to bypass the effect, press the BYPASS button. If the BYPASS LED is lit, there is no effect. To turn the effect on, press the BYPASS button once to turn off the LED. The AD15VT, AD30VT,AD50VT & AD100VT remember the bypass setting even if you switch modes or programs, or turn off the power.

MANUAL MODE

When the AD15VT, AD30VT, AD50VT or AD100VT is in Manual mode, it works just like a non-programmable guitar amp. In other words, the positions of all top panel selectors and knobs (except for the EDIT 1 knob) indicate exactly what you’re hearing.

GETTING TO MANUAL MODE

If the MANUAL LED is dark, you’re not in Manual mode. Press the MANUAL button; the MANUAL LED will light, and you’ll be in Manual mode.

NOTE: If the CH1 or CH2 LED is blinking (i.e., when you’re in the middle of selecting a writing-destination for the program), the MANUAL LED won’t light when you press the MANUAL button the first time. In this case, simply press the MANUAL button once again.

NOTE: In Manual mode when you edit parameters that aren’t defined by a knob setting (i.e., effect parameters or noise reduction settings), those settings are saved automati- cally, and will be recalled the next time you enter Manual mode. However if the EFFECTS selector is at a different position than it was when you were last in Manual mode, the default settings for that effect type will be loaded.

HINT: If you want to bypass the effect, press the BYPASS button. If the BYPASS LED is lit, there is no effect. To turn the effect on, press the BYPASS button once to turn off the LED. The AD15VT, AD30VT,AD50VT & AD100VT remember the bypass setting even if you switch modes, programs, or turn off the power.Creating and storing your own program

11

Image 15
Contents Page Important Safety Instructions Table of Contents Page Main Features IntroductionWelcome Aboard Signal Path Power AMP and the GloryValve Reactor Technology Quick Start SetupChecking OUT the Preset Programs Switching Between the Channels of a ProgramCreating Your OWN Sounds AMP Section VolumeGuitarist’s Guided Panel Tour Input SectionEffects Effect SectionTREBLE, MIDDLE, and Bass MasterPRESET/MANUAL/CHANNEL Section Write button Power SwitchAC power Power LevelReturn jack LINE/PHONEExternal Speaker OUT jack Send jackPreset Mode Selecting a Preset Program Channel Select Mode Selecting a Channel ProgramAbout the three operating modes Manual Mode Switching ChannelsGetting to Manual Mode Creating Your OWN Program Creating and storing your own programWhen you’ve come up with a sound you like, store the program Adjusting the Noise ReductionStoring Your Program Checking the Settings of a Program Original ValuesTurn the power off Restoring the Factory SettingsSwitching to Manual Mode Switch Using the VFS2 dual foot switchSwitching the Channel Program Switch Turning Effect Bypass ON/OFF SwitchAmp models and effects AMP ModelsControlling Factors Power AMP Accuracy Tube TalkTurn IT UP Black Boutique CLAC15 UK ’70s Boutique OD UK ModernNumetal US HigainEDIT3 EffectsEDIT1 EDIT2TAP CompFlanger Delay Amp isn’t powering up when the Power switch is on TroubleshootingYou can’t hear any effects Input/output jacks SpecificationsProgrammer’s Cheat Sheet Program Name EDIT2TAP+EDIT 1 /TAP