Vox AD15VT, AD30VT, AD50VT, AD10VT manual PRESET/MANUAL/CHANNEL Section

Page 11

TAP (EDIT 2) and LED

This button enables you to set the speed of a modulation-type effect (such as CHORUS or FLANGER) the delay time REVERB length; simply press the button twice at the desired interval.

The LED blinks at the specified speed or time.

HINT: To set the time to exactly match the tempo of a song, press the TAP button sev- eral times along with the song.

HINT: You can also adjust the speed or time, by holding down the TAP button and turning the EDIT 1 knob. (This is the EDIT 2 mode)

NOTE: If the BYPASS LED is lit, you won’t be able to use the TAP switch to set the time. (The TAP LED will be dark.)

BYPASS (EDIT 3) and LED

If you don’t want to use an effect, press this button to turn the effect off (i.e., bypassed). If the effect is bypassed, this LED will be lit.

NOTE: You can’t adjust the effect parameters if the BYPASS LED is lit.

HINT: While the effect is bypassed, you can adjust the noise reduction sensitivity by holding down the TAP button and turning the EDIT 1 knob.

HINT: The bypass setting is remembered even when you switch modes, switch pro- grams, or turn off the power.

HINT: The Bypass button can be used to modify effect parameters (EDIT 3). Press and hold Bypass and simultaneously turn the EDIT 1 knob. See the chart on page 23 for what parameters can be controlled.

4.PRESET/MANUAL/CHANNEL SECTION

PRESET and LED

This button puts your Valvetronix amp into Preset mode and you can use the AMP selector to select a “typical” setting for each amp type. If the PRESET LED is lit, you’re in Preset mode!

MANUAL and LED

This button puts your Valvetronix amp into Manual mode which means the physi- cal position of each knob (except for the EDIT 1 knob) determines exactly what you will hear. This means that the amp will operate just like a conventional guitar amp. If the MANUAL LED is lit, you’re in Manual mode.

CH (Channel), CH1/CH2 LEDs

This button switches between the two channels and The LED of the selected channel will light. In Preset or Manual mode, the CH1 and CH2 LEDs will be dark. If from either of these modes you then press this CH button, you’ll switch to Chan- nel Select mode, and the channel (1 or 2) that you selected most recently will become active.

7

Image 11
Contents Page Important Safety Instructions Table of Contents Page Welcome Aboard Main FeaturesIntroduction Valve Reactor Technology Signal PathPower AMP and the Glory Quick Start SetupCreating Your OWN Sounds Checking OUT the Preset ProgramsSwitching Between the Channels of a Program AMP Section VolumeGuitarist’s Guided Panel Tour Input SectionEffects Effect SectionTREBLE, MIDDLE, and Bass MasterPRESET/MANUAL/CHANNEL Section Write button Power SwitchAC power Power LevelReturn jack LINE/PHONEExternal Speaker OUT jack Send jackAbout the three operating modes Preset Mode Selecting a Preset ProgramChannel Select Mode Selecting a Channel Program Getting to Manual Mode Manual ModeSwitching Channels Creating Your OWN Program Creating and storing your own programWhen you’ve come up with a sound you like, store the program Adjusting the Noise ReductionStoring Your Program Checking the Settings of a Program Original ValuesTurn the power off Restoring the Factory SettingsSwitching to Manual Mode Switch Using the VFS2 dual foot switchSwitching the Channel Program Switch Turning Effect Bypass ON/OFF SwitchControlling Factors Amp models and effectsAMP Models Turn IT UP Power AMP AccuracyTube Talk Black Boutique CLAC15 UK ’70s Boutique OD UK ModernNumetal US HigainEDIT3 EffectsEDIT1 EDIT2TAP CompFlanger Delay Amp isn’t powering up when the Power switch is on TroubleshootingYou can’t hear any effects Input/output jacks SpecificationsProgrammer’s Cheat Sheet Program Name EDIT2TAP+EDIT 1 /TAP