Panasonic WJ-GXD900, WJ-GXE900 manual Reset Button Reset

Page 11

DIP1: Normally, select OFF. When ON is selected, the firmware, as the start up program (loaded at the factory), starts up. The value of the settings will not be deleted.

DIP2: When ON is selected, the IP address and all the current settings will return to the default settings.

DIP3: When ON is selected, the initialization of the IP address will start. (The initialization of the IP address starts only when the DIP4 is set to OFF.)

DIP4: When ON is selected, DHCP will be available.

DIP5: Normally, select OFF. To change to the Main CPU mode, select ON.

Note: The Main CPU mode is the advanced function for integrated control. Use these switches with the default settings for normal use.

DIP6: Reserved

DIP7: When ON is selected, the HTTP server will stop its service.

DIP8: Normally, select OFF.

To select the IPL (Initial Program Loader) mode for start up, set this switch to ON. (Only for testing)

To select the normal mode, set this switch to OFF.

tReset Button (RESET)

Pressing this button restarts the encoder without shutting down the power.

Press this button only when the encoder becomes unstable.

11

Image 11

Contents Operating Instructions English Version Important Safety Instructions Contents Controlling the BIT Rate of Streaming Video Resetting the Alarm / Displaying the Alarm StatusFeatures Precautions CPU TCP/IP, UDP, HTTP, FTP, ARP, Bootp System Requirements Limitation of LiabilityDocument Convention Trademarks and Registered TrademarksDip Switches 1 8 SW2 Power Indicator OperateStatus Indicators Status 1 Rotary Switch SW1 A, B, CReset Button Reset BNC MPEG2 Decoder Front Panel Network Status Indicators LINK1, 100, 1000, ACTRS-232C 9-pin D-sub Ethernet Port 100BASE-TX/1000BASE-T RJ-45 Signal Ground Terminal Signal GND Power CordMulticast Transmission ConnectionsVideo 100BASE-TX System Example Switching streaming videoAddress=aaa.aaa.aaa.aaappppp Operation Example Switching streaming videoControlling camera Digital Disk Recorder WJ-HD500 Series System example Recording streaming videoOperation Example Recording streaming video Setting Example Recording streaming videoRS-485 Data Port Setup Network Port SetupSystem Example Unicast TransmissionReceiving and Sending Serial Data RS-485 Required Settings for RS-485Alarm Reset Alarm Function and a Reset SwitchDetails of the TCP/IP Data part AlarmsAction of the encoder when an alarm is received Alarm notification commandAudio IN/AUDIO OUT Alarm ResetHeat Dissipation InstallationsPlaces to avoid About mountingMounting the decoder Rack MountingMounting the encoder How to install Installing in a container box Only for the EncoderCode label Labels for EncoderLabels for Decoder Description labelBefore Starting Settings SetupItems included in the software Setup with the Provided Panasonic IP Setup SoftwareSetup Using Windows 98 SE Network Setup of the PCSetup Using Windows Setup Using Windows XP Category View Setup Top page of the encoder Settings Menus of the EncoderNetwork AlarmMaintenance CONTROL/STATEControl CONTROL/STATEItem Descriptions Encode StateCamera No When using multicast transmissionWhen using unicast transmission VideoTTL Encoder Start UP SetupBIT Rate TOS BITGOP AudioVideo Loss Alarm AlarmAlarm Notification IP ADDRESS/ALARM Notification Port No Camera Site AlarmALARM-DRY Contact Timer CGI ResetAlarm OFF Timing ON/OFF ALARM-CAMERA SiteCGI Reset ALARM-VIDEO Loss CGI Reset Stop BIT RS-485 Data PortBaud Rate DataDestination Port No Destination SetupReference Setup Followings Destination IP Address in Receiving PacketNetwork System Daylight Savings Start UP CommandNTP Server HOST/IP Address Time ZoneUser Camera Control AdministratorHost Host IP ADDRESS/ Subnet MaskRestart MaintenanceFirmware Update Accept Exclusive Command IP AddressHOW to Update the Firmware Camera Control Defroster Program PresetFocus IrisCamera Menu Control Top page of the decoder Settings Menus of the DecoderDisplay Video page for each video output chan- nelDecode State Receiving Stream IP ADDRESS/RECEIVING Stream Port NoReceiving IP ADDRESS/RECEIVING Port No CH1 CH4UNICAST/MULTICAST Latency Buffer Decoder Start UP SetupDisplay Position DisplayCamera No. Display Date DisplayTime Display Character Background ColorYY/MM/DD hhmmss Year/Month/Day DD/MM/YY hhmmss Date/Month/YearEnter the IP address of the decoder Default setting is Decryption KEY 4 Digits 0 VIDEO&AUDIO DecryptionDevice NAME/ LOCATION/CONTACT/ Snmp Community User Host Click to add a host after entering the host information HOW to Update the Firmware Symptom TroubleshootingReference Network troubles LINK1 indicator does not lightAre the IP addresses set correctly? Video troublesEncoder may be down Image is not displayed correctlyAudio fragmentation occurs No audio Image is disturbed drop frame, etcHOW to USE the CGI Commands Item List Camera ControlFormat ResponseExamples Important NoticesControl Item List Camera Settings Menus ControlImportant Notice Examples Switching Streaming Video Example Start encoding Controlling Start /STOP of the EncoderExamples Start decoding Streaming transmission Controlling Start / Stop of the DecoderStop decoding Http /1.1 Xxxxxxxxxxxxx CR Displaying the Status of the EncoderExample Crlf Displaying the Status of the DecoderStatus of CH4 Controlling the BIT Rate of Streaming Video and Audio Data 101 Resetting the Alarm / Displaying the Alarm Status 103 Displaying the Contact Input Status Displaying the Status of Video Loss Muting the Audio Multiscreen Display Type Controlling the Contact OutputPIO OUT109 Restarting the Encoder / Decoder Updating Setting Default setting Default Settings60SEC Interval ALARM-VIDEO Loss Audio Setup OFF ALARM-DRY ContactRESET/TIMER SEC 60SEC Interval ALARM-CAMERA SiteNo Change 114Device Name Multicast IP Address for Setup Multicast PortLatency Buffer None Decoder Start UP Setup Display Time Display Hour User User Authentication OFF User NameInput/Output SpecificationsStandard Accessories Basic Specification117 118 N0603-1063 3TR001669BAB