Panasonic WJ-GXE900 manual Image is disturbed drop frame, etc, Audio fragmentation occurs No audio

Page 84

Symptom

The image is disturbed (drop frame, etc.).

•Audio troubles

Audio fragmentation occurs.

No audio.

Possible cause / Possible solution

Reference page

• Is a temporary network trouble (a broken wire,

 

 

 

connection trouble, etc.) occurring?

 

When temporary software trouble occurs, it will be

 

recovered automatically.

–

Depending on the status of the trouble, communication

 

might be disconnected. In this case, try to connect again.

 

If this happens frequently, reconsider the network

 

connections.

 

• Transmission delay may have occurred on the network.

 

 

 

Perform the setting of "LATENCY BUFFER" on the

70

VIDEO page of the decoder properly.

 

• Is a temporary network trouble (breaking of wire,

 

 

 

connection trouble, etc.) occurring?

 

When temporary software trouble occurs, it will be

 

recovered automatically.

 

Depending on the status of the trouble, communication

–

might be disconnected. In this case, try to connect again.

 

If this happens frequently, reconsider the network

 

connections.

 

• Is the audio device connected to the AUDIO OUT

 

 

 

connector correctly?

 

Connect the audio input connector of a monitor or

15

speakers to the AUDIO OUT connector of the

 

decoder correctly.

 

 

 

•Do the audio input and output levels match?

The AUDIO IN/OUT connectors of the encoder/decoder

are the LINE IN/OUT. It is necessary to connect the

–

microphone amplifier and the speaker amplifier.

 

• Is the setting for "AUDIO INPUT" of the AUDIO page of

 

 

the encoder set to "OFF"?

46

Check the settings on the AUDIO page of the encoder.

 

 

 

 

 

• Is the audio received by the decoder muted?

 

Release muting.

 

 

106

 

 

84

Page 83 Page 85
Image 84
Page 83 Page 85
Contents Operating Instructions English Version Important Safety Instructions Contents Resetting the Alarm / Displaying the Alarm Status Controlling the BIT Rate of Streaming VideoFeatures Precautions TCP/IP, UDP, HTTP, FTP, ARP, Bootp System RequirementsLimitation of Liability CPUTrademarks and Registered Trademarks Document ConventionPower Indicator Operate Status Indicators Status 1Rotary Switch SW1 A, B, C Dip Switches 1 8 SW2Reset Button Reset BNC Network Status Indicators LINK1, 100, 1000, ACT MPEG2 Decoder Front PanelRS-232C 9-pin D-sub Signal Ground Terminal Signal GND Power Cord Ethernet Port 100BASE-TX/1000BASE-T RJ-45Connections Multicast TransmissionVideo System Example Switching streaming video 100BASE-TXOperation Example Switching streaming video Controlling cameraAddress=aaa.aaa.aaa.aaappppp System example Recording streaming video Digital Disk Recorder WJ-HD500 SeriesSetting Example Recording streaming video RS-485 Data Port SetupNetwork Port Setup Operation Example Recording streaming videoUnicast Transmission System ExampleRequired Settings for RS-485 Receiving and Sending Serial Data RS-485Alarm Function and a Reset Switch Alarm ResetAlarms Action of the encoder when an alarm is receivedAlarm notification command Details of the TCP/IP Data partAlarm Reset Audio IN/AUDIO OUTInstallations Places to avoidAbout mounting Heat DissipationRack Mounting Mounting the decoderMounting the encoder Installing in a container box Only for the Encoder How to installLabels for Encoder Labels for DecoderDescription label Code labelSetup Before Starting SettingsSetup with the Provided Panasonic IP Setup Software Items included in the softwareSetup Network Setup of the PC Using Windows 98 SESetup Using Windows Setup Using Windows XP Category View Setup Settings Menus of the Encoder Top page of the encoderAlarm MaintenanceCONTROL/STATE NetworkCONTROL/STATE Item DescriptionsEncode State ControlWhen using multicast transmission When using unicast transmissionVideo Camera NoEncoder Start UP Setup BIT RateTOS BIT TTLAudio GOPAlarm Alarm Notification IP ADDRESS/ALARM Notification Port NoCamera Site Alarm Video Loss AlarmALARM-DRY Contact CGI Reset Alarm OFF TimingTimer ALARM-CAMERA Site ON/OFFCGI Reset ALARM-VIDEO Loss CGI Reset RS-485 Data Port Baud RateData Stop BITDestination Setup Reference Setup FollowingsDestination IP Address in Receiving Packet Destination Port NoNetwork System Start UP Command NTP Server HOST/IP AddressTime Zone Daylight SavingsUser Administrator HostHost IP ADDRESS/ Subnet Mask Camera ControlMaintenance Firmware UpdateAccept Exclusive Command IP Address RestartHOW to Update the Firmware Camera Control Program Preset FocusIris DefrosterCamera Menu Control Settings Menus of the Decoder Top page of the decoderVideo page for each video output chan- nel DisplayReceiving Stream IP ADDRESS/RECEIVING Stream Port No Decode StateCH1 CH4 UNICAST/MULTICASTReceiving IP ADDRESS/RECEIVING Port No Decoder Start UP Setup Latency BufferDisplay Camera No. DisplayDate Display Display PositionCharacter Background Color YY/MM/DD hhmmss Year/Month/DayDD/MM/YY hhmmss Date/Month/Year Time DisplayEnter the IP address of the decoder Default setting is VIDEO&AUDIO Decryption Decryption KEY 4 Digits 0Device NAME/ LOCATION/CONTACT/ Snmp Community User Host Click to add a host after entering the host information HOW to Update the Firmware Troubleshooting Symptom Network troubles LINK1 indicator does not light ReferenceVideo troubles Are the IP addresses set correctly?Image is not displayed correctly Encoder may be downImage is disturbed drop frame, etc Audio fragmentation occurs No audioHOW to USE the CGI Commands Camera Control FormatResponse Item ListImportant Notices ExamplesCamera Settings Menus Control Important NoticeControl Item List Examples Switching Streaming Video Example Controlling Start /STOP of the Encoder Start encodingExamples Controlling Start / Stop of the Decoder Start decoding Streaming transmissionStop decoding Displaying the Status of the Encoder Http /1.1 Xxxxxxxxxxxxx CRExample Displaying the Status of the Decoder CrlfStatus of CH4 Controlling the BIT Rate of Streaming Video and Audio Data 101 Resetting the Alarm / Displaying the Alarm Status 103 Displaying the Contact Input Status Displaying the Status of Video Loss Muting the Audio Multiscreen Display Controlling the Contact Output PIOOUT Type109 Restarting the Encoder / Decoder Updating Default Settings Setting Default settingAudio Setup OFF ALARM-DRY Contact RESET/TIMER SEC60SEC Interval ALARM-CAMERA Site 60SEC Interval ALARM-VIDEO Loss114 No ChangeMulticast IP Address for Setup Multicast Port Latency Buffer None Decoder Start UP Setup DisplayTime Display Hour User User Authentication OFF User Name Device NameSpecifications Standard AccessoriesBasic Specification Input/Output117 118 N0603-1063 3TR001669BAB
Top Page Image Contents