Panasonic WJ-GXD900 MPEG2 Decoder Front Panel, Network Status Indicators LINK1, 100, 1000, ACT

Page 13

!0Audio Input Connector (AUDIO IN 1 - 4)

 

!1Signal Ground Terminal (SIGNAL GND)

(–10 dB, 9-pin D-sub)

 

 

Up to 4 audio devices can be connected. To connect

 

!2 Power Cord

audio devices, a cable (WV-CA64, not supplied) is

 

Connect to an AC outlet (120V AC, 60 Hz).

required.

 

 

 

 

 

MPEG2 Decoder Front Panel

w e

LINK1 100 1000 ACT STATUS 1 2 3 4 5 6 7 8

OPERATE

BLINKING TEMPERATURE WARNING

MPEG2 Decoder WJ-GXD900

q

LINK1 100 1000 ACT STATUS 1 2 3 4 5 6 7 8

OPERATE

BLINKING TEMPERATURE WARNING

A B C

SW1

ON

 

WJ-GXD900

SW2

RESET

qPower Indicator (OPERATE)

This indicator lights up when the power of the decoder is on.

When the temperature inside the decoder becomes remarkably high, this indicator will start blinking.

It will take around 2 minutes to start up the decoder after turning the power on.

During start up, the STATUS indicators (STATUS 1 -

5)will light up in order. When the STATUS 5 indicator lights up, it is possible to operate the decoder.

Each STATUS indicator will light, blink or go off according to the status of this decoder.

r t y u

wNetwork Status Indicators (LINK1, 100, 1000, ACT)

LINK1 Indicator: This indicator lights up when the connection with the network is established.

100 Indicator: This indicator lights up during the 100BASE-TX connection.

1000 Indicator: This indicator lights up during the 1000BASE-T connection.

ACT Indicator: This indicator lights up when the decoder is receiving or sending packets.

eStatus Indicators (STATUS 1 - 4)

STATUS 1 - 4: These indicators display the status of VIDEO OUT 1 - 4.

Each of the STATUS 1 - 4 indicators displays the status of the VIDEO OUT 1 - 4 connectors respectively. The respective STATUS indicator

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operating Instructions English Version Important Safety Instructions Contents Controlling the BIT Rate of Streaming Video Resetting the Alarm / Displaying the Alarm StatusFeatures Precautions System Requirements TCP/IP, UDP, HTTP, FTP, ARP, BootpLimitation of Liability CPUDocument Convention Trademarks and Registered TrademarksStatus Indicators Status 1 Power Indicator OperateRotary Switch SW1 A, B, C Dip Switches 1 8 SW2Reset Button Reset BNC MPEG2 Decoder Front Panel Network Status Indicators LINK1, 100, 1000, ACTRS-232C 9-pin D-sub Ethernet Port 100BASE-TX/1000BASE-T RJ-45 Signal Ground Terminal Signal GND Power CordMulticast Transmission ConnectionsVideo 100BASE-TX System Example Switching streaming videoControlling camera Operation Example Switching streaming videoAddress=aaa.aaa.aaa.aaappppp Digital Disk Recorder WJ-HD500 Series System example Recording streaming videoRS-485 Data Port Setup Setting Example Recording streaming videoNetwork Port Setup Operation Example Recording streaming videoSystem Example Unicast TransmissionReceiving and Sending Serial Data RS-485 Required Settings for RS-485Alarm Reset Alarm Function and a Reset SwitchAction of the encoder when an alarm is received AlarmsAlarm notification command Details of the TCP/IP Data partAudio IN/AUDIO OUT Alarm ResetPlaces to avoid InstallationsAbout mounting Heat DissipationMounting the decoder Rack MountingMounting the encoder How to install Installing in a container box Only for the EncoderLabels for Decoder Labels for EncoderDescription label Code labelBefore Starting Settings SetupItems included in the software Setup with the Provided Panasonic IP Setup SoftwareSetup Using Windows 98 SE Network Setup of the PCSetup Using Windows Setup Using Windows XP Category View Setup Top page of the encoder Settings Menus of the EncoderMaintenance AlarmCONTROL/STATE NetworkItem Descriptions CONTROL/STATEEncode State ControlWhen using unicast transmission When using multicast transmissionVideo Camera NoBIT Rate Encoder Start UP SetupTOS BIT TTLGOP AudioAlarm Notification IP ADDRESS/ALARM Notification Port No AlarmCamera Site Alarm Video Loss AlarmALARM-DRY Contact Alarm OFF Timing CGI ResetTimer ON/OFF ALARM-CAMERA SiteCGI Reset ALARM-VIDEO Loss CGI Reset Baud Rate RS-485 Data PortData Stop BITReference Setup Followings Destination SetupDestination IP Address in Receiving Packet Destination Port NoNetwork System NTP Server HOST/IP Address Start UP CommandTime Zone Daylight SavingsUser Host AdministratorHost IP ADDRESS/ Subnet Mask Camera ControlFirmware Update MaintenanceAccept Exclusive Command IP Address RestartHOW to Update the Firmware Camera Control Focus Program PresetIris DefrosterCamera Menu Control Top page of the decoder Settings Menus of the DecoderDisplay Video page for each video output chan- nelDecode State Receiving Stream IP ADDRESS/RECEIVING Stream Port NoUNICAST/MULTICAST CH1 CH4Receiving IP ADDRESS/RECEIVING Port No Latency Buffer Decoder Start UP SetupCamera No. Display DisplayDate Display Display PositionYY/MM/DD hhmmss Year/Month/Day Character Background ColorDD/MM/YY hhmmss Date/Month/Year Time DisplayEnter the IP address of the decoder Default setting is Decryption KEY 4 Digits 0 VIDEO&AUDIO DecryptionDevice NAME/ LOCATION/CONTACT/ Snmp Community User Host Click to add a host after entering the host information HOW to Update the Firmware Symptom TroubleshootingReference Network troubles LINK1 indicator does not lightAre the IP addresses set correctly? Video troublesEncoder may be down Image is not displayed correctlyAudio fragmentation occurs No audio Image is disturbed drop frame, etcHOW to USE the CGI Commands Format Camera ControlResponse Item ListExamples Important NoticesImportant Notice Camera Settings Menus ControlControl Item List Examples Switching Streaming Video Example Start encoding Controlling Start /STOP of the EncoderExamples Start decoding Streaming transmission Controlling Start / Stop of the DecoderStop decoding Http /1.1 Xxxxxxxxxxxxx CR Displaying the Status of the EncoderExample Crlf Displaying the Status of the DecoderStatus of CH4 Controlling the BIT Rate of Streaming Video and Audio Data 101 Resetting the Alarm / Displaying the Alarm Status 103 Displaying the Contact Input Status Displaying the Status of Video Loss Muting the Audio Multiscreen Display PIO Controlling the Contact OutputOUT Type109 Restarting the Encoder / Decoder Updating Setting Default setting Default SettingsRESET/TIMER SEC Audio Setup OFF ALARM-DRY Contact60SEC Interval ALARM-CAMERA Site 60SEC Interval ALARM-VIDEO LossNo Change 114Latency Buffer None Decoder Start UP Setup Display Multicast IP Address for Setup Multicast PortTime Display Hour User User Authentication OFF User Name Device NameStandard Accessories SpecificationsBasic Specification Input/Output117 118 N0603-1063 3TR001669BAB

WJ-GXD900, WJ-GXE900 specifications

The Panasonic WJ-GXE900 and WJ-GXD900 are top-tier video encoders designed to meet the increasing demands of surveillance applications. These devices are essential in providing high-quality video transmission over IP networks, making them ideal for both security and monitoring purposes.

One of the standout features of the WJ-GXE900 is its advanced encoding capability. It supports H.265 and H.264 compression standards, allowing for efficient bandwidth usage without compromising video quality. This technology is particularly beneficial for environments where bandwidth might be limited, as it significantly reduces the data load while maintaining impressive clarity, even in challenging lighting conditions.

The WJ-GXD900, on the other hand, is designed for high-definition video encoding. It also utilizes H.265 and H.264 technologies, but offers enhanced image processing capabilities. This includes advanced noise reduction, which helps to produce clearer images during low-light situations. Both models utilize 4K resolution support, allowing users to capture ultra-high-definition video, which is crucial for applications requiring detailed surveillance footage.

Another key characteristic of both models is their versatility in integration with IP cameras and other devices. They are compatible with a wide range of Panasonic and third-party IP cameras, ensuring that users can build a surveillance system tailored to their specific needs. This interoperability is vital for large installations where multiple camera types might be used.

The WJ-GXE900 and WJ-GXD900 also feature intuitive web-based interfaces, simplifying the setup and configuration processes. Users can easily manage settings, stream video, and monitor performance remotely from any device with internet access. This remote management capability is increasingly important in today's fast-paced environments, where quick responses and monitoring are critical.

Additionally, both models support multiple streaming options, including the ability to deliver video to various destinations simultaneously. This feature is particularly useful for organizations needing to distribute video feeds to multiple monitors or devices, enhancing real-time surveillance capabilities.

In conclusion, the Panasonic WJ-GXE900 and WJ-GXD900 are powerful video encoders that combine advanced technology with user-friendly features. Their support for high-quality video encoding, integration flexibility, and remote management capabilities make them excellent choices for any modern surveillance system. These devices exemplify Panasonic's commitment to innovation, reliability, and high-performance solutions in the realm of security technology.
Top Page Image Contents