Panasonic CF-74GCDADBM service manual Arranging the W-LAN L and R Cable

Page 31

Arranging the W-LAN L and R Cable

W-LAN Antenna L PCB

W-LAN Antenna R PCB

Attach the Tape to hold the Cable.

Pass the Cable through the notch and lead it downward.

Lead the Cable along the surface.

Attach the Tape to each of the Cables. (Avoid overlapping.)

Avoid overlapping of the Cables (all the way).

Pass the Cable through the notch. (Avoid running over the ribs.)

Pass the Cable through the notch and lead it downward.

Pass the Cable between the boss and rib.

LCD Rear Cabnet

Pass the Cable through the notch. (Avoid running over the ribs.)

Attaching the LCD Damper C and LCD Damper D

1.Attach the four LCD Damper C to the upper part and lower part of the LCD Unit.

2.Attach the LCD Damper D to the upper center of the LCD Unit.

A

LCD Damper D

 

0~1mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Match the LCD Damper D to the center of the LCD Unit.

LCD Unit

A

LCD Display Side

0~1mm

LCD Damper C

LCD Rear Side

LCD Damper C

A

A: Match the LCD Damper C by LCD edge 0~2mm

9-9

Image 31
Contents Model No. CF-74GCDADBM Page Laser Safety Information Page Page Contents Specifications Wireless LAN Only for model with wireless LAN Data transfer rate of DVD per 1X speed is 1,350 KB/s Names and Functions of Parts Right side Block Diagram Page Troubleshooting Power-On Self Test Boot Check Stuck key 02D0 System cache error Cache disabled Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device To skip Bios password Wiring Connection Diagram HDD Unit Battery PackPreparation Removing the HDDRemoving the Dimm Memory Card Removing the Bottom Case Removing the Handle AssyRemoving the PC Card Ejector Lithium Battery Removing the Wireless Module and MDC ModuleRemoving the Main PCB PCB Removing the LCD and the Inverter Removing the USB PCBRemoving the Display unit Removing the LCD Front CabinetRemoving the Finger PCB Removing the Touch PAD and PAD PCBPreparation Reassembly Instructions Attaching the LCD Damper C and LCD Damper D Arranging the W-LAN L and R CableAttaching the Cloth Arranging the LCD/TS CableSetting the Inverter and Arranging the Inverter Cable Arranging the TP Power Cable and Attaching the TP/LCD SheetLCD Unit Setting the Display unit Setting the LCD Front CabinetFixing of the LCD Front Cabinet Arranging the USB Cable Setting the USB PCBSetting the SD PCB, Heat Sink FAN Motor Setting the BT PCBApplying Grease on the Heat Sink Arranging the DC-IN Cable Setting the DC-IN PCB and I/O PCBArranging the Lithium Battery Setting the PC Card Ejector and Lithium BatteryArranging the FAN Cable Arranging the Modem Cable Setting the Wireless Module and MDC ModuleSetting the Handle Assy Setting the Bottom CaseSoldering the Speaker Cable and Setting the Speaker Rubber Setting the Speaker and the LED PCBComputer, and set the Keyboard to the computer Setting the KeyboardSetting the HDD Setting the Dimm Memory Card and Dimm CoverLatch HDD Unit Battery Pack DVD-ROM Drive Unit Exploded View Screw tightening torque Screw tightening torque CF-74GCDADBM Replacement Parts List Accessories DFHR6214ZB Sleeve B DFBH3045YB Hinge L Description EEFCX0G151R Thermistor Serial Eeprom B1GBCFNN0042 Transistor DEARA8AJ104M Resistor Array ERJ2RKF1502X RESISTOR, 1/16W, 15KΩ DC-IN PCB SD PCB