Panasonic CF-74GCDADBM service manual Setting the BT PCB, Setting the SD PCB, Heat Sink FAN Motor

Page 37

9.2.7.Setting the BT PCB.

1.Connect the BT FFC to the Connector (CN22).

2.Fix the BT PCB to the computer using the two Screws <N9>.

BT P.C.B. <N9><N9>

BT FFC

9.2.8.Setting the SD PCB, Heat Sink and

FAN Motor

1.Connect the SD FFC to the Connector (CN1401).

2.Fix the SD PCB to the computer using the three Screws<N9>.

3.Set the Heat Sink, Fan Duct and the four Heat Sink Springs.

4.Fix the FAN Motor to the computer using the two Screws<N5>.

5.Attach the Fan Tape 1 and 2 on the FAN Motor, and fix the Cable Holder on them.

Screws <N5>: DXSB2+6FNL

Screws <N9>: DFHE5025XA

Cable Holder

 

Fan Tape1

Fan Tape2

Fan Duct

<N5>

 

<N9>

SD PCB

SD FFC

 

 

FAN Motor

CN1401

Heat Sink

Heat Sink

Heat Sink

Spring

 

Spring

9-15

Image 37
Contents Model No. CF-74GCDADBM Page Laser Safety Information Page Page Contents Specifications Wireless LAN Only for model with wireless LAN Data transfer rate of DVD per 1X speed is 1,350 KB/s Names and Functions of Parts Right side Block Diagram Page Troubleshooting Power-On Self Test Boot Check Stuck key 02D0 System cache error Cache disabled Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device To skip Bios password Wiring Connection Diagram Preparation Battery PackRemoving the HDD HDD UnitRemoving the Dimm Memory Card Removing the Bottom Case Removing the Handle AssyRemoving the PC Card Ejector Lithium Battery Removing the Wireless Module and MDC ModuleRemoving the Main PCB PCB Removing the Display unit Removing the USB PCBRemoving the LCD Front Cabinet Removing the LCD and the InverterRemoving the Finger PCB Removing the Touch PAD and PAD PCBPreparation Reassembly Instructions Attaching the LCD Damper C and LCD Damper D Arranging the W-LAN L and R CableAttaching the Cloth Arranging the LCD/TS CableSetting the Inverter and Arranging the Inverter Cable Arranging the TP Power Cable and Attaching the TP/LCD SheetLCD Unit Setting the Display unit Setting the LCD Front CabinetFixing of the LCD Front Cabinet Arranging the USB Cable Setting the USB PCBSetting the SD PCB, Heat Sink FAN Motor Setting the BT PCBApplying Grease on the Heat Sink Arranging the DC-IN Cable Setting the DC-IN PCB and I/O PCBArranging the Lithium Battery Setting the PC Card Ejector and Lithium BatteryArranging the FAN Cable Arranging the Modem Cable Setting the Wireless Module and MDC ModuleSetting the Handle Assy Setting the Bottom CaseSoldering the Speaker Cable and Setting the Speaker Rubber Setting the Speaker and the LED PCBComputer, and set the Keyboard to the computer Setting the KeyboardSetting the HDD Setting the Dimm Memory Card and Dimm CoverLatch HDD Unit Battery Pack DVD-ROM Drive Unit Exploded View Screw tightening torque Screw tightening torque CF-74GCDADBM Replacement Parts List Accessories DFHR6214ZB Sleeve B DFBH3045YB Hinge L Description EEFCX0G151R Thermistor Serial Eeprom B1GBCFNN0042 Transistor DEARA8AJ104M Resistor Array ERJ2RKF1502X RESISTOR, 1/16W, 15KΩ DC-IN PCB SD PCB