Panasonic CF-74GCDADBM Setting the Wireless Module and MDC Module, Arranging the Modem Cable

Page 42

9.2.12. Setting the Wireless Module and MDC Module

1.Connect the Modem Cable to the Connector, and fix the MDC Module to the Main PCB using the two Screws<N9>.

2.Connect the Wireless Module to the Connector of the Main PCB, and fix it using the two Screws<N9>.

3.Connect the two Antenna Cables to the two Connectors on the Wireless Module.

Antenna Cable (Black): MAIN Connector

Antenna Cable (Gray): AUX Connector

Screws <N9>: DFHE5025XA

<N9>

Kapton Tape

Antenna Cable (Black)

Antenna Cable (Gray)

Wireless Module

<N9>

MDC Module

Modem Cable

Arranging the Modem Cable

<Preparation for assembly of the MDC Module>

Arranging the Modem Cable

MDC Module

10–3mm

S1

Safety Working

Ensure the Kapton Tape is overlapping the Shrink Tube by 1 mm or more.

<Good example>

Safety Working S2

Ensure the Cable does not run over the Screw. Ensure the Cable does not come over the end of the MDC Module.

Kapton Tape

Pass the Cable over the CCC mark.

Fix the Connector

Modem Cable

using the Tape.

 

Fold back and attach to the back side of the MDC Module.

Ensure both of the inlet and outlet of the Cable are within the frame.

Avoid any stress on the outlet of the Cable.

<Bad example>

Coming over the end of the Screw.

Safety Working

S2

Coming over the end of the Screw.

Coming outside of the frame.

 

9-20

Image 42
Contents Model No. CF-74GCDADBM Page Laser Safety Information Page Page Contents Specifications Wireless LAN Only for model with wireless LAN Data transfer rate of DVD per 1X speed is 1,350 KB/s Names and Functions of Parts Right side Block Diagram Page Troubleshooting Power-On Self Test Boot Check Stuck key 02D0 System cache error Cache disabled Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device To skip Bios password Wiring Connection Diagram Removing the HDD Battery PackPreparation HDD UnitRemoving the Dimm Memory Card Removing the Handle Assy Removing the Bottom CaseRemoving the Wireless Module and MDC Module Removing the PC Card Ejector Lithium BatteryRemoving the Main PCB PCB Removing the LCD Front Cabinet Removing the USB PCBRemoving the Display unit Removing the LCD and the InverterRemoving the Touch PAD and PAD PCB Removing the Finger PCBPreparation Reassembly Instructions Arranging the W-LAN L and R Cable Attaching the LCD Damper C and LCD Damper DArranging the LCD/TS Cable Attaching the ClothArranging the TP Power Cable and Attaching the TP/LCD Sheet Setting the Inverter and Arranging the Inverter CableLCD Unit Setting the LCD Front Cabinet Setting the Display unitFixing of the LCD Front Cabinet Setting the USB PCB Arranging the USB CableSetting the BT PCB Setting the SD PCB, Heat Sink FAN MotorApplying Grease on the Heat Sink Setting the DC-IN PCB and I/O PCB Arranging the DC-IN CableSetting the PC Card Ejector and Lithium Battery Arranging the Lithium BatteryArranging the FAN Cable Setting the Wireless Module and MDC Module Arranging the Modem CableSetting the Bottom Case Setting the Handle AssySetting the Speaker and the LED PCB Soldering the Speaker Cable and Setting the Speaker RubberSetting the Keyboard Computer, and set the Keyboard to the computerSetting the Dimm Memory Card and Dimm Cover Setting the HDDLatch HDD Unit Battery Pack DVD-ROM Drive Unit Exploded View Screw tightening torque Screw tightening torque CF-74GCDADBM Replacement Parts List Accessories DFHR6214ZB Sleeve B DFBH3045YB Hinge L Description EEFCX0G151R Thermistor Serial Eeprom B1GBCFNN0042 Transistor DEARA8AJ104M Resistor Array ERJ2RKF1502X RESISTOR, 1/16W, 15KΩ DC-IN PCB SD PCB