Panasonic CF-74GCDADBM service manual Setting the PC Card Ejector and Lithium Battery

Page 40

9.2.10. Setting the PC Card Ejector and Lithium Battery

1.Attach the Lithium Battery to the Main PCB.

2.Pass the Lead Wire of the Lithium Battery through the groove of the Main PCB, and connect it to the Connector (CN14) on the back side.

3.Fix the PC Card Ejector to the Main PCB using the two Screws<N9>.

Screws <N9>: DFHE5025XA

Lithium Battery

(to CN14)

CN14

PC Card Ejector

Main PCB

<N9>

Arranging the Lithium Battery

Safety Working S2

Pass the Cable through the groove of the Main PCB.

Match the end of the Tape. (0 to 1 mm)

Tape

Main PCB

Connect to the Connector (CN14) on the back side.

Match the end of the Tape. (0 to 1 mm)

Fix the Cable using the Tape.

Pass the Cable between the parts. (Avoid running over the parts.)

Lithium Battery

9.2.11.Setting the Main PCB

Note:

After replacing the Main Board, rewrite the BIOS ID.

1.Set the MP Guide to the Main PCB.

2.Set the Main PCB to the computer.

3.Fix the Main PCB using the six Screws<N9>.

4.Connect the ten Cables to the corresponding Connecters (CN6, CN7, CN24, CN19, CN28, CN21, CN802, CN18, CN15, CN25).

Screws <N9>: DFHE5025XA

<N9>	CN21
CN6	CN802
CN6
	CN18
Main PCB	CN15

CN7

CN24

CN28<N9>

CN19

MP Guide

CN26

9-18

Image 40

Contents Model No. CF-74GCDADBM Page Laser Safety Information Page Page Contents Specifications Wireless LAN Only for model with wireless LAN Data transfer rate of DVD per 1X speed is 1,350 KB/s Names and Functions of Parts Right side Block Diagram Page Troubleshooting Power-On Self Test Boot Check Stuck key 02D0 System cache error Cache disabled Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device To skip Bios password Wiring Connection Diagram Battery Pack PreparationRemoving the HDD HDD UnitRemoving the Dimm Memory Card Removing the Handle Assy Removing the Bottom CaseRemoving the PC Card Ejector Lithium Battery Removing the Wireless Module and MDC ModuleRemoving the Main PCB PCB Removing the USB PCB Removing the Display unitRemoving the LCD Front Cabinet Removing the LCD and the InverterRemoving the Finger PCB Removing the Touch PAD and PAD PCBPreparation Reassembly Instructions Arranging the W-LAN L and R Cable Attaching the LCD Damper C and LCD Damper DArranging the LCD/TS Cable Attaching the ClothArranging the TP Power Cable and Attaching the TP/LCD Sheet Setting the Inverter and Arranging the Inverter CableLCD Unit Setting the Display unit Setting the LCD Front CabinetFixing of the LCD Front Cabinet Setting the USB PCB Arranging the USB CableSetting the BT PCB Setting the SD PCB, Heat Sink FAN MotorApplying Grease on the Heat Sink Setting the DC-IN PCB and I/O PCB Arranging the DC-IN CableSetting the PC Card Ejector and Lithium Battery Arranging the Lithium BatteryArranging the FAN Cable Setting the Wireless Module and MDC Module Arranging the Modem CableSetting the Bottom Case Setting the Handle AssySetting the Speaker and the LED PCB Soldering the Speaker Cable and Setting the Speaker RubberSetting the Keyboard Computer, and set the Keyboard to the computerSetting the Dimm Memory Card and Dimm Cover Setting the HDDLatch HDD Unit Battery Pack DVD-ROM Drive Unit Exploded View Screw tightening torque Screw tightening torque CF-74GCDADBM Replacement Parts List Accessories DFHR6214ZB Sleeve B DFBH3045YB Hinge L Description EEFCX0G151R Thermistor Serial Eeprom B1GBCFNN0042 Transistor DEARA8AJ104M Resistor Array ERJ2RKF1502X RESISTOR, 1/16W, 15KΩ DC-IN PCB SD PCB