Panasonic PT-L595U Switching the signal mode during RGB signal input, Signal data No. of dots

Page 20

<Switching the signal mode during RGB signal input>

If the picture is not projected normally when the selected input source is “RGB 1” or “RGB 2” because the signal mode selected does not match, select the correct signal mode by the procedure given below. The factory pre- setting is “AUTO”, so the projector can usually be used without the need to change this setting.

Setting procedure

1.Press the MENU button to display the MENU screen.

2.Press the “ ” and “ ” buttons to select “PICTURE”.

3.Press the “<” and “>” buttons to display the PICTURE screen.

4.Press the “ ” and “ ” buttons to select “SIGNAL MODE”.

5.Press the “<” and “>” buttons to switch the signal name.

Refer to the table below when switching to the matching signal mode.

Display mode name

 

 

Signal data

 

No. of dots

Horizontal scanning frequency (kHz)

Vertical scanning frequency (Hz)

 

AUTO

Automatically switches to whichever of the following signal modes best matches the input signal

VGA 400

640

× 400

31.5

70.0

VGA 480

640

× 480

31.5

60.0

MAC 13

640

× 480

35.0

66.7

PC 98

640

× 400

24.8

56.4

VESA

640 × 480

37.9

72.8

S-VGA 1

800

× 600

35.2

56.3

S-VGA 2

800 × 600

37.9

60.4

S-VGA 3

800 × 600

46.9

75.0

S-VGA 4

800 × 600

48.1

72.0

S-VGA 5

800 × 600

32.1

51 .0

MAC 16

832 × 624

49.7

74.6

XGA 1

1024 × 768

48.4

60.0

XGA 2

1 0 2

4 × 6 8

56.4

70.0

XGA 3

1024 × 768

68.7

85.0

MAC 19

1024 × 768

60.2

75.0

NOTE:

The display resolution for the PT-L595U projector is 800 × 600 dots. If any of the above signals which have resolutions greater than this are input, the resolution will be converted to 800 × 600 dots.

The setting screen and the MENU screen can both be cleared by pressing the MENU button.

19

Image 20
Contents LCD Projector Dear Panasonic Customer ContentsFeatures Important Safety Notice Precautions with regard to safety Setting-upWhen using the projector If problems occur during useCleaning and maintenance Take particular care when replacing the lamp unitDo not place any heavy objects on top of the projector Do not look into the lens while the projector is being usedPrecautions on handling About condensationSide view Location and function of each partFront view Top and front RGB 2 RGB IN/AUDIO Back, bottom and right viewSide terminal board Before using the remote control unit Operating range of the remote control unit If facing the remote control unit toward the screenTurning the power on and off Turning on the powerTurning off the power Power button Main Power switchScreen characteristics reference Screen requirementsStandard setting-up positions Standard setting-up dimensionsProjection size Projection distance L Minimum MaximumAdjusting the position of the projected picture Setting the projector up horizontally Retracting the adjustable legsAdjustment procedure Adjuster button Adjustable legsAdjusting the lens Adjustment procedure for direct adjustmentSetting-up positions and changing the projection method Setting procedureFront mounting Rear mountingBasic operation Changing the input sourceSwitching the signal mode during RGB signal input Signal data No. of dotsAuto VesaSystem format selection for S-VIDEO Video input signals AutoNtsc SecamAdjusting the volume Adjusting the picture to the desired setting Adjusting the white balance BAL R BAL G BAL BAdjusting the sound to the desired setting Adjustment procedure for volume adjustmentAdjusting the picture position When adjusting the horizontal position H-POSIWhen adjusting the vertical position V-POSI Adjustment procedure for horizontal position adjustmentAdjusting the blanking Left-side blanking correction for the H-BLK-LTop blanking correction for the V-BLK-T Bottom blanking correction for the V-BLK-BWhen decreasing the horizontal amplitude Adjusting the horizontal amplitudeWhen increasing the horizontal amplitude Numeric adjustment Level display Adjustment procedure Using other useful functions Disabling the Power button of the remote control unitChanging the on-screen display language to another language Using the power save function Setting procedure System configuration example Example of connection to audio-visual equipmentAudio system Laser disc player VCRSUB Example of connection to a computerSUB HD Display mode name/No. of dots S1 S2 S3 S4 S5 S6 Accessory mouse cableAbout the Macintosh adapter OperationUsing the serial connector Pin layout and signal names for Serial connectorCommunication settings Basic formatControl commands Cable specificationsIndicators Lamp indicator Temp indicatorProblem Possible cause RemedyCleaning the air filter Indent Air filter clamp Air filter coverClean the air filter and the air filter clamps Install the air filter coverLamp unit replacement period Replacing the lamp unitFixing screw for the lamp unit Replacement procedureLamp unit cover Fixing screw for the lamp unit cover Page Before asking for service, check the following points Possible causeSpecifications RGB HD/SYNC RGB OUT Audio Video Audio in L-RCeiling Mount Bracket ET-PK592 Trademark AcknowledgementsFCC Dimensions Western Zone Eastern ZoneCentral Zone