Panasonic PT-L595U manual Adjusting the volume

Page 22

Adjusting the volume

The volume can be adjusted by pressing the VOL (+/-) buttons on the remote control unit.

Remote control unit

Turning off the sound

If the “+” button is pressed, the volume will increase, and if the “-” button is pressed, the volume will decrease.

NOTE:

If these buttons are pressed while the on-screen display for another function is currently on the screen, the volume will still be adjusted but the current volume setting and the volume bar display will not appear.

The volume can also be adjusted from an on-screen display menu. Refer to page 24 for details on how to do this.

The volume output level will remain displayed on the screen for approximately three seconds.

If the MUTE button on the remote control unit is pressed, “MUTE” will be displayed on the screen as shown in the illustration below and the sound will be muted. If the MUTE button is pressed once more, the on-screen display will be cleared and the normal sound volume will be restored. The volume output level will remain displayed on the screen for approximately three seconds.

Remote control unit

NOTE:

 

If the MUTE button is pressed while the on-screen display

 

for another function is currently on the screen, the volume

 

will still be muted but the “MUTE” on-screen display will not

 

appear.

 

If the power supply is turned off or either of the VOL (+/-)

 

buttons is pressed, the mute setting will be canceled.

 

It is also possible to have the picture turn off together with

 

the sound when the MUTE button is pressed. Refer to page

 

32 for details on how to change this setting.

 

When the picture has been turned off in this way, the words

 

“PICTURE MUTE” will be displayed on the screen.

Resetting adjustment values to the factory pre-settings (standard values)

If the STD (Standard) button on the remote control unit is pressed while the PICTURE screen, POSITION screen, AUDIO screen or one of the individual adjustment screens is being displayed, the adjustment settings being displayed will be reset to the factory pre-settings.

Remote control unit

If the STD (Standard) button on the remote control unit is

 

pressed while the PICTURE screen, POSITION screen or

 

AUDIO screen is being displayed, the letters “STD” will be

 

displayed in yellow in the top-right corner of the screen and

 

all items displayed will be reset to the factory pre-settings.

 

NOTE:

 

However, the “TV-SYSTEM” and “ SIGNAL MODE” settings

 

in the PICTURE screen and the “VOLUME” setting in the

 

AUDIO screen will not return to the factory pre-settings.

 

If the STD (Standard) button on the remote control unit is

 

pressed while one of the individual adjustment screens is

 

being displayed, the value and the bar display will be

 

appeared in yellow and only the item displayed will be reset

 

to the factory pre-setting.

21

Image 22
Contents LCD Projector Features ContentsDear Panasonic Customer Important Safety Notice When using the projector Precautions with regard to safetySetting-up If problems occur during useDo not place any heavy objects on top of the projector Cleaning and maintenanceTake particular care when replacing the lamp unit Do not look into the lens while the projector is being usedPrecautions on handling About condensationFront view Location and function of each partSide view Top and front Side terminal board Back, bottom and right viewRGB 2 RGB IN/AUDIO Before using the remote control unit Operating range of the remote control unit If facing the remote control unit toward the screenTurning off the power Turning the power on and offTurning on the power Power button Main Power switchScreen characteristics reference Screen requirementsProjection size Projection distance L Standard setting-up positionsStandard setting-up dimensions Minimum MaximumAdjusting the position of the projected picture Adjustment procedure Setting the projector up horizontallyRetracting the adjustable legs Adjuster button Adjustable legsAdjusting the lens Adjustment procedure for direct adjustmentFront mounting Setting-up positions and changing the projection methodSetting procedure Rear mountingBasic operation Changing the input sourceAuto Switching the signal mode during RGB signal inputSignal data No. of dots VesaNtsc System format selection for S-VIDEO Video input signalsAuto SecamAdjusting the volume Adjusting the picture to the desired setting Adjusting the white balance BAL R BAL G BAL BAdjusting the sound to the desired setting Adjustment procedure for volume adjustmentWhen adjusting the vertical position V-POSI Adjusting the picture positionWhen adjusting the horizontal position H-POSI Adjustment procedure for horizontal position adjustmentTop blanking correction for the V-BLK-T Adjusting the blankingLeft-side blanking correction for the H-BLK-L Bottom blanking correction for the V-BLK-BWhen increasing the horizontal amplitude Adjusting the horizontal amplitudeWhen decreasing the horizontal amplitude Numeric adjustment Level display Adjustment procedure Using other useful functions Disabling the Power button of the remote control unitChanging the on-screen display language to another language Using the power save function Setting procedure Audio system Laser disc player System configuration exampleExample of connection to audio-visual equipment VCRSUB HD Example of connection to a computerSUB About the Macintosh adapter Display mode name/No. of dots S1 S2 S3 S4 S5 S6Accessory mouse cable OperationCommunication settings Using the serial connectorPin layout and signal names for Serial connector Basic formatControl commands Cable specificationsProblem IndicatorsLamp indicator Temp indicator Possible cause RemedyCleaning the air filter Indent Air filter clamp Air filter coverClean the air filter and the air filter clamps Install the air filter coverLamp unit replacement period Replacing the lamp unitLamp unit cover Fixing screw for the lamp unit cover Replacement procedureFixing screw for the lamp unit Page Before asking for service, check the following points Possible causeSpecifications RGB HD/SYNC RGB OUT Audio Video Audio in L-RFCC Trademark AcknowledgementsCeiling Mount Bracket ET-PK592 Dimensions Central Zone Eastern ZoneWestern Zone