Panasonic PT-L595U Indicators, Lamp indicator Temp indicator, Problem, Possible cause Remedy

Page 39

Indicators

There are two indicators on the front of the projector which give information about the operating condition of the projector. These indicators illuminate or flash to warn you about problems that have occurred inside the projector, so if you notice that one of the indicators is on, turn off the power and check the table below for the cause of the problem.

LAMP indicator

TEMP indicator

Indicator name

Indicator display

Problem

 

 

The internal

 

 

projector

 

 

temperature is too

 

Illuminated (red)

high.

TEMP indicator

 

 

 

 

The metal halide lamp

TEMP

 

has turned off

 

automatically because

 

Flashing (red)

 

the internal

 

 

temperature has risen

 

 

to an abnormally high

 

 

level.

Possible cause

Remedy

The ventilation holes

Uncover the ventilation holes.

may be covered.

 

The ambient

Set up the projector in a place

temperature in the

where the temperature is between

place of use may

41°F (5°C) and 104°F (40°C)

be too high.

and the humidity is between 10%

 

and 80% (with no condensation).

The air filter may

Turn off the main power

be blocked.

supply by following the

 

procedure on page 11, and

 

then clean the air filter (refer

 

to page 39).

Illuminated (red)

LAMP indicator

LAMP

Flashing (red)

 

It is nearly time to replace the lamp unit.

The metal halide lamp switches off automatically.

Does “LAMP” appear on the screen after the projector is turned on?

The power may have been turned on immediately after it was turned off.

There may be an abnormality in the lamp circuit.

This occurs when the operation time for the lamp unit is nearing 1,800 hours. Ask your dealer or an Authorized Service Center to replace the lamp unit.

Wait for a while until the lamp unit cools down before turning the power back on again.

Turn off the main power supply by following the procedure on page 11, and then contact an Authorized Service Center.

NOTE:

Be sure to turn off the main power by following the procedure given in “Turning the power on and off” on page 11 before carrying out any of the procedures in the “Remedy” column.

If the main power turns off after the TEMP indicator starts flashing, it means that an abnormality has occurred. Please contact an Authorized Service Center so that the necessary repairs can be made.

38

Image 39
Contents LCD Projector Contents FeaturesDear Panasonic Customer Important Safety Notice If problems occur during use Precautions with regard to safetySetting-up When using the projectorDo not look into the lens while the projector is being used Cleaning and maintenanceTake particular care when replacing the lamp unit Do not place any heavy objects on top of the projectorAbout condensation Precautions on handlingLocation and function of each part Front viewSide view Top and front Back, bottom and right view Side terminal boardRGB 2 RGB IN/AUDIO Before using the remote control unit If facing the remote control unit toward the screen Operating range of the remote control unitPower button Main Power switch Turning the power on and offTurning on the power Turning off the powerScreen requirements Screen characteristics referenceMinimum Maximum Standard setting-up positionsStandard setting-up dimensions Projection size Projection distance LAdjusting the position of the projected picture Adjuster button Adjustable legs Setting the projector up horizontallyRetracting the adjustable legs Adjustment procedureAdjustment procedure for direct adjustment Adjusting the lensRear mounting Setting-up positions and changing the projection methodSetting procedure Front mountingChanging the input source Basic operationVesa Switching the signal mode during RGB signal inputSignal data No. of dots AutoSecam System format selection for S-VIDEO Video input signalsAuto NtscAdjusting the volume Adjusting the picture to the desired setting BAL R BAL G BAL B Adjusting the white balanceAdjustment procedure for volume adjustment Adjusting the sound to the desired settingAdjustment procedure for horizontal position adjustment Adjusting the picture positionWhen adjusting the horizontal position H-POSI When adjusting the vertical position V-POSIBottom blanking correction for the V-BLK-B Adjusting the blankingLeft-side blanking correction for the H-BLK-L Top blanking correction for the V-BLK-TAdjusting the horizontal amplitude When increasing the horizontal amplitudeWhen decreasing the horizontal amplitude Numeric adjustment Level display Adjustment procedure Disabling the Power button of the remote control unit Using other useful functionsChanging the on-screen display language to another language Using the power save function Setting procedure VCR System configuration exampleExample of connection to audio-visual equipment Audio system Laser disc playerExample of connection to a computer SUB HDSUB Operation Display mode name/No. of dots S1 S2 S3 S4 S5 S6Accessory mouse cable About the Macintosh adapterBasic format Using the serial connectorPin layout and signal names for Serial connector Communication settingsCable specifications Control commandsPossible cause Remedy IndicatorsLamp indicator Temp indicator ProblemIndent Air filter clamp Air filter cover Cleaning the air filterInstall the air filter cover Clean the air filter and the air filter clampsReplacing the lamp unit Lamp unit replacement periodReplacement procedure Lamp unit cover Fixing screw for the lamp unit coverFixing screw for the lamp unit Page Possible cause Before asking for service, check the following pointsRGB HD/SYNC RGB OUT Audio Video Audio in L-R SpecificationsTrademark Acknowledgements FCCCeiling Mount Bracket ET-PK592 Dimensions Eastern Zone Central ZoneWestern Zone