Panasonic PT-L595U manual Adjusting the picture to the desired setting

Page 23

Adjusting the picture to the desired setting

You can adjust the picture settings for any of the input signal sources selected according to the procedure on page 18. The items which can be adjusted vary depending on the type of input signal. The adjustment procedure below describes the on-screen displays when a signal is being input to the S-VIDEO IN terminal or the VIDEO IN terminal.

Adjustment procedure <for the COLOR setting>

1.Press the MENU button to display the MENU screen.

2.Press the “ ” and “ ” buttons to select “PICTURE”.

3.Press the “<” and “>” buttons to display the PICTURE screen.

4.Press the “ ” and “ ” buttons to select “COLOR”.

NOTE:

If the STD (Standard) button is pressed while the PICTURE screen at right is being displayed, the letters “STD” will be displayed in yellow in the top-right corner of the screen and all settings other than the TV-SYSTEM setting will be reset to the factory pre-settings. Furthermore, the values and bar displays for items which have returned to the factory pre-settings will be displayed in yellow.

5.Press the “<” and “>” buttons to display the COLOR individual adjustment screen.

6.Continue pressing the “<” and “>” buttons to adjust the color. The current setting will be displayed on the screen by numerals and a bar.

The adjustment operation and the changes made will vary depending on which adjustment item is selected. Refer to the table below for details.

Adjustment function display

Adjustment Item

Button

Numeric adjustment level display

Bar display

Adjustment Details

Adjustment Range

Remarks

Press the “>” button.

COLOR

Press the “<” button.

Press the “>” button.

TINT

Press the “<” button.

Press the “>” button.

BRIGHT

Press the “<” button.

Press the “>” button.

CONTRAST

Press the “<” button.

Press the “>” button.

SHARPNESS

Press the “<” button.

NOTE:

The color becomes darker. The color becomes lighter. Flesh tones become greenish. Flesh tones become reddish. The screen becomes brighter. The screen becomes darker.

The screen becomes brighter and the picture becomes darker.

The screen becomes darker and the picture becomes lighter.

The picture quality becomes sharper. The picture quality becomes softer.

Max. value 63 S-VIDEO/VIDEO only Min. value 0

Max. value 63 NTSC, NTSC 4.43 (S-

Min. value 0 VIDEO/VIDEO)only Max. value 63

Min. value 0

Max. value 63

Min. value 0

Max. value 63 S-VIDEO/VIDEO only Min. value 0

If approximately five seconds pass without any buttons being pressed while an individual adjustment screen is being displayed, the display will return to the PICTURE screen.

Press the MENU button to return to the PICTURE screen or to clear the MENU screen.

If the STD (Standard) button is pressed while one of the individual adjustment screens is being displayed, the value and the bar display will be appeared in yellow and only the item displayed will be reset to the factory pre- setting.

Refer to page 20 for details on the TV-SYSTEM setting which is displayed in the PICTURE screen, and to the following page for details on the W-BAL R/G/B setting which is displayed when RGB signals are being input. Furthermore, refer to page 19 for details on the SIGNAL MODE setting when RGB signals are being input.

If a PAL or SECAM signal is being input, the TINT item will not appear on the screen.

22

Page 22 Page 24
Image 23
Page 22 Page 24
Contents LCD Projector Dear Panasonic Customer ContentsFeatures Important Safety Notice If problems occur during use Precautions with regard to safetySetting-up When using the projectorDo not look into the lens while the projector is being used Cleaning and maintenanceTake particular care when replacing the lamp unit Do not place any heavy objects on top of the projectorAbout condensation Precautions on handlingSide view Location and function of each partFront view Top and front RGB 2 RGB IN/AUDIO Back, bottom and right viewSide terminal board Before using the remote control unit If facing the remote control unit toward the screen Operating range of the remote control unitPower button Main Power switch Turning the power on and offTurning on the power Turning off the powerScreen requirements Screen characteristics referenceMinimum Maximum Standard setting-up positionsStandard setting-up dimensions Projection size Projection distance LAdjusting the position of the projected picture Adjuster button Adjustable legs Setting the projector up horizontallyRetracting the adjustable legs Adjustment procedureAdjustment procedure for direct adjustment Adjusting the lensRear mounting Setting-up positions and changing the projection methodSetting procedure Front mountingChanging the input source Basic operation Vesa Switching the signal mode during RGB signal input Signal data No. of dots AutoSecam System format selection for S-VIDEO Video input signalsAuto NtscAdjusting the volume Adjusting the picture to the desired setting BAL R BAL G BAL B Adjusting the white balanceAdjustment procedure for volume adjustment Adjusting the sound to the desired settingAdjustment procedure for horizontal position adjustment Adjusting the picture positionWhen adjusting the horizontal position H-POSI When adjusting the vertical position V-POSIBottom blanking correction for the V-BLK-B Adjusting the blankingLeft-side blanking correction for the H-BLK-L Top blanking correction for the V-BLK-TWhen decreasing the horizontal amplitude Adjusting the horizontal amplitudeWhen increasing the horizontal amplitude Numeric adjustment Level display Adjustment procedure Disabling the Power button of the remote control unit Using other useful functionsChanging the on-screen display language to another language Using the power save function Setting procedure VCR System configuration exampleExample of connection to audio-visual equipment Audio system Laser disc playerSUB Example of connection to a computerSUB HD Operation Display mode name/No. of dots S1 S2 S3 S4 S5 S6Accessory mouse cable About the Macintosh adapterBasic format Using the serial connectorPin layout and signal names for Serial connector Communication settingsCable specifications Control commandsPossible cause Remedy IndicatorsLamp indicator Temp indicator ProblemIndent Air filter clamp Air filter cover Cleaning the air filterInstall the air filter cover Clean the air filter and the air filter clampsReplacing the lamp unit Lamp unit replacement periodFixing screw for the lamp unit Replacement procedureLamp unit cover Fixing screw for the lamp unit cover Page Possible cause Before asking for service, check the following pointsRGB HD/SYNC RGB OUT Audio Video Audio in L-R SpecificationsCeiling Mount Bracket ET-PK592 Trademark AcknowledgementsFCC Dimensions Western Zone Eastern ZoneCentral Zone
Top Page Image Contents