Panasonic PT-L595U Replacement procedure, Lamp unit cover Fixing screw for the lamp unit cover

Page 43

Replacement procedure

NOTE:

If the lamp unit is replaced after it has been used for more than 2,000 hours, the projector will switch to standby mode after approximately 10 minutes of operation. Steps 7. to 11. on the following page should thus be completed within 10 minutes.

1.Disconnect the power cord plug from the wall outlet and check that the area around the lamp unit has cooled down.

2.Use a Phillips screwdriver to remove the screw which is securing the lamp unit cover at the right side of the projector, and then remove the lamp unit cover.

NOTE:

Read the CAUTION on the lamp unit cover before continuing.

Lamp unit cover

Fixing screw for the lamp unit cover

3.Turn the fixing screw for the lamp unit by hand until it turns freely.

CAUTION:

The lamp unit will be hot after it has been used, and you might receive burns if you touch it while it is still hot.

Fixing screw for the lamp unit
4. Hold the handle which is attached to the lamp unit and gently pull	Handle
the lamp unit out from the projector.

5.Insert the new lamp unit, while making sure that the direction of insertion is correct, and then turn the fixing screw for the lamp unit by hand until it is securely tightened.

NOTE:

Insert the lamp unit so that the fixing screw for the lamp unit is facing downward.

6.Securely install the lamp unit cover, and then use a Phillips screwdriver to securely tighten the fixing screw for the lamp unit cover.

NOTE:

Be sure to install the lamp unit and the lamp unit cover securely. If they are not securely installed, it may cause the protection circuit to operate so that the power cannot be turned on.

42

Image 43

Contents LCD Projector Features ContentsDear Panasonic Customer Important Safety Notice If problems occur during use Precautions with regard to safetySetting-up When using the projectorDo not look into the lens while the projector is being used Cleaning and maintenanceTake particular care when replacing the lamp unit Do not place any heavy objects on top of the projectorAbout condensation Precautions on handlingFront view Location and function of each partSide view Top and front Side terminal board Back, bottom and right viewRGB 2 RGB IN/AUDIO Before using the remote control unit If facing the remote control unit toward the screen Operating range of the remote control unitPower button Main Power switch Turning the power on and offTurning on the power Turning off the powerScreen requirements Screen characteristics referenceMinimum Maximum Standard setting-up positionsStandard setting-up dimensions Projection size Projection distance LAdjusting the position of the projected picture Adjuster button Adjustable legs Setting the projector up horizontallyRetracting the adjustable legs Adjustment procedureAdjustment procedure for direct adjustment Adjusting the lensRear mounting Setting-up positions and changing the projection methodSetting procedure Front mountingChanging the input source Basic operationVesa Switching the signal mode during RGB signal inputSignal data No. of dots AutoSecam System format selection for S-VIDEO Video input signalsAuto NtscAdjusting the volume Adjusting the picture to the desired setting BAL R BAL G BAL B Adjusting the white balanceAdjustment procedure for volume adjustment Adjusting the sound to the desired settingAdjustment procedure for horizontal position adjustment Adjusting the picture positionWhen adjusting the horizontal position H-POSI When adjusting the vertical position V-POSIBottom blanking correction for the V-BLK-B Adjusting the blankingLeft-side blanking correction for the H-BLK-L Top blanking correction for the V-BLK-TWhen increasing the horizontal amplitude Adjusting the horizontal amplitudeWhen decreasing the horizontal amplitude Numeric adjustment Level display Adjustment procedure Disabling the Power button of the remote control unit Using other useful functionsChanging the on-screen display language to another language Using the power save function Setting procedure VCR System configuration exampleExample of connection to audio-visual equipment Audio system Laser disc playerSUB HD Example of connection to a computerSUB Operation Display mode name/No. of dots S1 S2 S3 S4 S5 S6Accessory mouse cable About the Macintosh adapterBasic format Using the serial connectorPin layout and signal names for Serial connector Communication settingsCable specifications Control commandsPossible cause Remedy IndicatorsLamp indicator Temp indicator ProblemIndent Air filter clamp Air filter cover Cleaning the air filterInstall the air filter cover Clean the air filter and the air filter clampsReplacing the lamp unit Lamp unit replacement periodLamp unit cover Fixing screw for the lamp unit cover Replacement procedureFixing screw for the lamp unit Page Possible cause Before asking for service, check the following pointsRGB HD/SYNC RGB OUT Audio Video Audio in L-R SpecificationsFCC Trademark AcknowledgementsCeiling Mount Bracket ET-PK592 Dimensions Central Zone Eastern ZoneWestern Zone