Panasonic AWHE50HN WwOther 2/2 screen, Tally Enable Disable, Enable, OSD Off With Tally Off, On

Page 47

Setting the menu items

wwOther 2/2 screen

	Other 2/2
Tally Enable		Enable
OSD	Off With Tally	Off
OSD	Status	Off
Wireless Control		Enable

Return

Tally Enable [Disable, Enable]

“Enable” or “Disable” is set here for the function which turns on or turns off the tally lamp using the tally control signal.

OSD Off With Tally [Off, On]

This is used to enable or disable the function for clearing the OSD menu displays when the tally signal is received by a command or contact.

When the tally signal is released, the original OSD menu displays are restored.

OSD Status [Off, On]

“On” or “Off” is set here for the status display which appears during AWB operations.

Wireless Control [Disable, Enable]

“Enable” or “Disable” is set here for operations conducted from the wireless remote control.

The operations are enabled when the unit’s power is turned on from an external device other than a wireless remote control, and they are disabled when the power is turned on from a wireless remote control.

At the point when this item’s setting is changed, the new setting is not reflected in operation.

It is reflected when the unit is set to the standby mode and its power is turned on.

Follow one of the procedures below if the item’s setting is changed by mistake and the unit can no longer be operated from a wireless remote control.

When menu operations can be performed using another control device:

First change the item using a control device capable of performing menu operations, and then turn off the unit’s power and turn it back on.

When menu operations cannot be performed using other control devices:

1.Turn off the power of the units and devices that are connected.

2.Disconnect the unit’s power cable, and plug it back in.

3.Perform the operation for turning on the unit’s power from the wireless remote control.

4.After changing this item, turn off the unit’s power and turn it back on.

Return

Use this to return to the previous menu.

47

Image 47

Contents

AW‑HE50SN Contents WwConcerning the Operating Instructions Before useWwOverview WwAbout copyright and licence WwRequired personal computer environmentWwTrademarks and registered trademarks WwNetwork security WwDisclaimer of warrantyBasic shooting operations Select the shooting modeWhen the AW‑RP50 is connected How to turn the power on and offWwTurning the power on Set the Operate switch on the controller to onSet the Operate switch on the controller to OFF WwTurning the power offWwTypes of shooting modes Selecting the unitsSelecting the shooting modes scene files WwHow to select the shooting mode Press the OK button again Press the Menu buttonTurn the jog dial main Press the OK buttonQqChanging the camera’s direction QqUsing the zoom functionQqSwitching the direction or zoom speed ShootingMenu screen is displayed Lens focus is not adjusted automaticallyUnit does not move Multiple color bands color bars are displayedMore advanced operations Manual shooting WwManually adjusting the focusWwManually adjusting the iris Press the Shutter button and turn its lamp on WwManually adjusting the shutter speedPress the Gain button to turn off its lamp WwManually adjusting the gainPress the OFF, LOW or HI button Position may occur Preset memoriesHold down the Memory button Set to the memory recording modeSet the memory recording mode Hold down the Reset buttonWhen the AW‑RP555 is connected QqAutomatic adjustment AWB AWB A or AWB B White balance adjustmentWwWhite balance adjustment Press the AWC button Press the SET button for 2 secondsQqAuto tracking white adjustment ATW Press the IRIS - button Black level master pedestal adjustmentWwBlack level master pedestal adjustment Press the M/IRIS buttonPress the Iris button several times to turn off its lamp QqHorizontal phase adjustment Genlock adjustment AW‑HE50S onlyWwGenlock adjustment Press the Mode button QqColor phase adjustmentGenlock adjustment AW‑HE50S only Table of operations Basic operationsChanging Press the  or  button to change the setting Jog dial R Jog dial mainPress the Menu button for 2 seconds to exit the camera menu QqProcedure for camera menu operation AW‑RP655Mode button lights up at the BAR setting Press the Item button QqProcedure for camera menu operation AW‑RP555Press the Menu button of the AW‑RP555 for 2 seconds Perform one of the following steps to select the menu itemCamera OSD QqProcedure for camera menu operation AW‑RP50WwTop Menu Setting the menu itemsWwSetting the menu items WwCamera screen When Manual1 to 3 is selected WwCamera screen When FullAuto is selectedWwContrast screen WwPicture 1/2 screen WwSystem screen WwPicture 2/2 screen WwOutput screen WwGenlock screen AW‑HE50S onlyRGB-NOR Format unchanged screen QqChanging the formatFormat change check screen Format Set screenWwOther 1/2 screen OSD Off With Tally Off, On Tally Enable Disable, EnableWireless Control Disable, Enable WwOther 2/2 screenWwFirmware Version screen WwMaintenance screenInitialize screen Menu settings initialized screenMenu settings unchanged screen QqConcerning initializationMenu item table Menu Factory setting Selection items FullAutoWeb setting screen WwMenu operations Control Setup Power on button / Standby button  Control button / Setup button Zoom  Focus WwControl screen Brightness  Preset Control pad and its buttons  Basic button WwSetup screenQqBasic screen QqImage screen Image  Image Image adjustPreset position Image adjust screen  Scene FullAuto, Manual1, Manual2, Manual3  Contrast Contrast Mode Auto, ManualAWB  Picture Chroma Level -3 to +3Preset position setting screen  Preset  Zoom  Limitation Setting  Genlock AW‑HE50S only  Output ENH setting instead Other QqUser mng  Host check Host auth. screen  Host auth IP address QqServer IP address QqNetworkNetwork screen  IP network Port numbers already used 20, 21, 23, 25, 42, 53, 67, 68 Default gatewaySubnet mask  Host name 1 to 64 half-size characters  Password 0 to 32 half-size characters Access interval Ddns screen Contact 0 to 255 half-size characters Snmp screen Community 0 to 32 half-size characters  Location 0 to 32 half-size characters Time & date QqMaintenance Error description System log screenClick the Execute button Upgrade screenEnter the software version in the xxxxx part  Reset to the default and load the default Html files Default reset screen Reset to the default Except the network settings  Load the default Html files setup menu Upload Back up screen Download Other screen Category Display Description of error DDNS-related error displaysNTP-related error displays Login-related displaysLimiters Press one of the CAM1 to CAM4 buttons to select the unit Setting/releasing the limitersWwSetting the limiters WwBasic limiter operationsPp Releasing the lower limit position of the movement range WwResetting the limitersWwReleasing the limiters Pp Releasing the upper limit position of the movement rangeTrouble-triggered safe mode Safe modeWwConcerning the safe mode CPU WwSystem requirements for a PCSolution WwPrecautions when using Windows VistaSymptom Symptom QqRestrictions Restriction When activating audio on the web browserWwPrecautions when using Windows Restriction 2 When using Windows 7 with some products Restriction 1 On the setup pages for some productsPanasonic Solutions Company

Related manuals

Manual 90 pages 20.69 Kb