Fujitsu ST4000 warranty Calibrating the PEN, Installing a PEN Tether, Replacing the PEN TIP

Page 33

sponds to the right mouse button. The rear toggle of the barrel button switch acts as an electronic ink “eraser”.

C A U T I O N

Ensure that a screen protector is installed on the Tablet PC screen before you use the pen. The warranty does not cover a scratched screen.

Use only the pen provided with your Tablet PC. Do not use substitutes that were not designed for the Stylistic ST4000 Series Tablet PC.

Here are some hints that may help you use the pen more effectively:

To activate the tip switch, tap or hold the pen tip against the screen.

To activate the barrel button switch, press and hold the end of the button you wish to use (front toggle is the right mouse button switch; the rear toggle acts as an electronic “eraser”.

To move the cursor, hold the pen tip within 1/8 inch (3 - 5mm) from the screen and move the pen.

To start a program, double-tap the pen tip (tap the pen tip twice rapidly) on the program icon as you would double-click a mouse.

To select an object, tap the pen tip on the object once.

To “double-click” an object, tap twice on the object quickly.

To move, or “drag”, an object on the screen, place the pen tip directly over the object, then as you hold the pen tip against the screen, move the pen.

CALIBRATING THE PEN

For information about calibrating your pen, refer to the literature that came with the operating system.

INSTALLING A PEN TETHER

To prevent dropping or losing your pen, you should attach it to your system using the pen tether that is included with the system.

To attach the pen tether to your Tablet PC, perform the following steps:

1.Attach the end of the pen tether with the smaller loop to your pen. Do do so, push the end of the tether through the hole in the pen, then thread the opposite end of the tether through the loop. (See Figure 2-2.)

U s i n g Y o u r S t y l i s t i c S T 4 0 0 0

Pen tether attachment point

Larger loop

Smaller loop

Figure 2-2. Installing a Pen Tether

2.Attach the end of the pen tether with the larger loop to the attachment point on your pen tablet. To do so, insert the end of the pen tether through the attach- ment point, then feed the pen through the large loop in the tether.

REPLACING THE PEN TIP

With use, the pen tip may become worn or may pick up foreign particles that can scratch the screen. A damaged or worn tip may not move freely, causing unpredictable results when using the pen. If your pen exhibits these problems, you should replace the pen tip. To do so, use the pen tip removal tool included with your pen.

Gap

Figure 2-3. Tip Removal Tool

To remove the tip, position the tip in the gap between the two ends of the tool. Pinch the tool together so the tip is firmly clasped, then pull it from the barrel. If the tip is worn or damaged, discard it.

To replace the tip, retrieve one of the new tips that accompanied your pen. Insert the flat end of the tip into the barrel and push it in firmly until it is seated.

If you need more tips, they can be ordered from the Fujitsu Web site at: www.fujitsupc.com.

23

Image 33
Contents Complies with Part 15 of the FCC Rules Fujitsu PC CorporationPage Table of Contents Appendix Preface Page Warranty Information About this GuideFujitsu Contact Information Page Getting Started with Your Tablet PC Page IN-BOX Items for the Stylistic ST4000 Series Tablet PC Getting Started with Your Stylistic Tablet PCOptional Accessories Front Features Stylistic Tablet PC FeaturesThermal Suede Memory module cover Removable cover over the memory modulesTop Features Left-Side Features Right-Side Features Icon Mode/State LED State Remarks Status DisplayHDD AccessApplication Buttons Tablet Button SettingsTablet Icon DescriptionApplication Buttons Primary and Secondary Functions Navigation Buttons Tertiary Functions of Application and Navigation Buttons Connector Connectors and Peripheral InterfacesPurpose PeripheralNetwork LAN Connector Tablet PC Purpose PeripheralPage Using Your Stylistic ST4000 Series Tablet PC Page System States Using the Stylistic ST4000 Series Tablet PCShutting Down the System Powering UP the Tablet PCSuspending System Operation To Change StatePower icon is blinking Suspend-to-RAMmode Power icon is not displayed Hibernate Save-to-DiskmodeU T I O N Using the PEN Adjusting the Display BrightnessFrom Suspend-to-RAM mode From Hibernate Save-to-Disk modeInstalling a PEN Tether Calibrating the PENReplacing the PEN TIP Charging the Battery Removing and Installing the BatteryI N T Tips for Conserving Battery Power Modem ConnectionPC Card Slot Installing a Memory Module Removing and Installing Memory ModulesTo install a Dimm module in the Tablet PC Removing a Memory ModuleCare and Maintenance Page Protecting the Display Screen Care and MaintenanceTroubleshooting Cleaning the Display ScreenStoring the Tablet PC Avoiding OverheatingSpeaker/Headphone Volume Too Low Configuring Peripheral InterfacesTablet PC is Not Responding to the Pen Page Specifications Page Physical Specifications Stylistic ST4000 SpecificationsDisplay Specifications Interface SpecificationsPower Specifications Environmental SpecificationsAdditional Specifications Agency Notices Page FCC Registration Number Regulatory InformationE R T I S S E M E N T Avis Aux Utilisateurs Du Réseau Téléphonique CanadienFor Authorized Repair Technicians Only UL NoticeR N I N G S System DisposalPage Appendix Page Regulatory Notes and Statements FCC Regulatory InformationFederal Communications Commission statement FCC Interference StatementCharacteristics of the Device Before Using this DeviceWireless LAN Modes Using this Device How to Handle This DeviceSetting Parameters Connecting Windows 2000 SystemsWhen you finish your entry, click Apply WorkflowTCP/IP Settings Network SettingsEncryption Key Setup Network Connection WindowsSetting File and Printer Sharing for Microsoft Networks Checking the full computer name and workgroupSharing Sharing Files Accessing Another ComputerPrinter Sharing Checking the ConnectionChecking connectivity Connecting Windows XP SystemsOn Wireless Network Connection Properties, click General Network SettingsNetwork Connection Click OKSharing Setting computer name and workgroupTransfer data for send Tx and receive Troubleshooting Table Windows XP Click Start All Programs Accessories Windows 2000 Click Start Programs AccessoriesYou want to store the IP address Click Enter, then go to the location you specified above.Windows Problem Possible CauseSetting IP Addresses Problem Possible Cause Possible SolutionAbout IP Addresses Windows XPVCC SpecificationsPage Battery gauge Battery gauge icon Battery icon Battery pack Adjusting the display brightness Air flow vents , 6Battery power Battery release latchPower on/suspend/resume Button Power usage Pen tether Peripheral connectorsSolving problems Speaker Speaker/headphone volume too low Stylistic ST4000 specificationsSystem interface connector Y l i s t i c S T 4 0 0 0 S e r i e s T a b l e t P C