Fujitsu ST4000 warranty Connecting Windows XP Systems, Checking connectivity

Page 61

Item

Description

 

 

Link Quality

Shows either [Excellent], [Good],

 

[Fair], [Poor], or [Not Connected],

 

depending on the link quality.

 

Not shown for AdHoc connection.

 

 

Signal Strength

Shows either [Excellent], [Good],

 

[Fair], [Poor], or [Not Connected],

 

depending on the signal strength.

 

Not shown for AdHoc connection.

 

 

Table 7: Checking connectivity

CONNECTING WINDOWS XP SYSTEMS

This chapter describes how to set up the wireless LAN connection for computers that are running Windows XP.

P O I N T

If you purchased a Stylistic ST4000 Series Tablet PC with the optional integrated wireless LAN device, the device and drivers have already been installed. This procedure outlines the steps for setting the device parameters.

Updated drivers and/or utilities may become available after this manual is printed; see any addenda or fliers that may be included in the system packaging.

Workflow

The proper setup of the wireless LAN connection requires that several steps be performed in the proper order. Following is a general outline of the steps to be performed. Each step is detailed later in this procedure.

1.Setting parameters

■Setting the profile

■Setting the encryption

2.Network settings

■Setting the protocol and checking the network

■Setting file and printer sharing

■Checking the connection

Setting Parameters

1.Click [Start] -> [Control Panel].

2.Click [Network and Internet connections].

3.Click [Network connection]. A list of networks that are currently installed is displayed.

4.Right click [Intersil PRISM Wireless LAN PCI Card] in the list, and click [Properties] from the menu that is displayed. [Wireless Network Connection Proper- ties] appears.

W i r e l e s s L A N U s e r ’ s G u i d e

5.Click the [Wireless Networks] tab. The [Wireless Networks] tab appears.

6.Perform the following steps.

■Make sure that [Use Windows to configure my wire- less network settings] is checked.

■Click [Add] under [Preferred networks]. [Wireless Network Properties] appears.

7.Set parameters in accordance with Table 8.

■For the AdHoc network, specify the same value to all the computers, for which the encryption key is used for connection.

■For the infrastructure network, specify the encryp- tion key (network key) with the same value to the encryption key of the access point. For how to check the encryption keys set for the access point, refer to the manual supplied with the access point.

P O I N T

Be sure to specify the encryption keys. If you do not specify the keys, any computer with a wireless LAN card can be connected. This presents a risk that other users may steal or destroy your data.

 

Item

 

Description

 

 

 

 

Network

 

Enter the network name to which you

Name

 

want to connect. This is a required item.

SSID

 

For the network name, ask your LAN

 

 

administrator.

 

 

 

AdHoc network: Set the same name for all

 

 

of the computers that are to be connected.

 

 

Infrastructure network: Specify the same

 

 

name as that specified on the access point

 

 

that is to be connected. For access point

 

 

instructions, refer to the manual that

 

 

comes with the access point.

 

 

 

 

 

51

Page 60 Page 62
Image 61
Page 60 Page 62
Contents Complies with Part 15 of the FCC Rules Fujitsu PC CorporationPage Table of Contents Appendix Preface Page About this Guide Warranty InformationFujitsu Contact Information Page Getting Started with Your Tablet PC Page IN-BOX Items for the Stylistic ST4000 Series Tablet PC Getting Started with Your Stylistic Tablet PCOptional Accessories Front Features Stylistic Tablet PC FeaturesThermal Suede Memory module cover Removable cover over the memory modulesTop Features Left-Side Features Right-Side Features Icon Mode/State LED State Remarks Status DisplayHDD AccessApplication Buttons Tablet Button SettingsTablet Icon DescriptionApplication Buttons Primary and Secondary Functions Navigation Buttons Tertiary Functions of Application and Navigation Buttons Connector Connectors and Peripheral InterfacesPurpose PeripheralNetwork LAN Connector Tablet PC Purpose PeripheralPage Using Your Stylistic ST4000 Series Tablet PC Page System States Using the Stylistic ST4000 Series Tablet PCShutting Down the System Powering UP the Tablet PCSuspending System Operation To Change StatePower icon is not displayed Hibernate Save-to-Diskmode Power icon is blinking Suspend-to-RAMmodeU T I O N Using the PEN Adjusting the Display BrightnessFrom Suspend-to-RAM mode From Hibernate Save-to-Disk modeCalibrating the PEN Installing a PEN TetherReplacing the PEN TIP Removing and Installing the Battery Charging the BatteryI N T Modem Connection Tips for Conserving Battery PowerPC Card Slot Installing a Memory Module Removing and Installing Memory ModulesTo install a Dimm module in the Tablet PC Removing a Memory ModuleCare and Maintenance Page Protecting the Display Screen Care and MaintenanceTroubleshooting Cleaning the Display ScreenStoring the Tablet PC Avoiding OverheatingConfiguring Peripheral Interfaces Speaker/Headphone Volume Too LowTablet PC is Not Responding to the Pen Page Specifications Page Physical Specifications Stylistic ST4000 SpecificationsDisplay Specifications Interface SpecificationsEnvironmental Specifications Power SpecificationsAdditional Specifications Agency Notices Page FCC Registration Number Regulatory InformationE R T I S S E M E N T Avis Aux Utilisateurs Du Réseau Téléphonique CanadienFor Authorized Repair Technicians Only UL NoticeR N I N G S System DisposalPage Appendix Page Regulatory Notes and Statements FCC Regulatory InformationFederal Communications Commission statement FCC Interference StatementCharacteristics of the Device Before Using this DeviceWireless LAN Modes Using this Device How to Handle This DeviceSetting Parameters Connecting Windows 2000 SystemsWhen you finish your entry, click Apply WorkflowTCP/IP Settings Network SettingsEncryption Key Setup Network Connection WindowsChecking the full computer name and workgroup Setting File and Printer Sharing for Microsoft NetworksSharing Sharing Files Accessing Another ComputerPrinter Sharing Checking the ConnectionChecking connectivity Connecting Windows XP SystemsOn Wireless Network Connection Properties, click General Network SettingsNetwork Connection Click OKSharing Setting computer name and workgroupTransfer data for send Tx and receive Troubleshooting Table Windows XP Click Start All Programs Accessories Windows 2000 Click Start Programs AccessoriesYou want to store the IP address Click Enter, then go to the location you specified above.Windows Problem Possible CauseSetting IP Addresses Problem Possible Cause Possible SolutionAbout IP Addresses Windows XPVCC SpecificationsPage Battery gauge Battery gauge icon Battery icon Battery pack Adjusting the display brightness Air flow vents , 6Battery power Battery release latchPower on/suspend/resume Button Power usage Pen tether Peripheral connectorsSolving problems Speaker Speaker/headphone volume too low Stylistic ST4000 specificationsSystem interface connector Y l i s t i c S T 4 0 0 0 S e r i e s T a b l e t P C
Top Page Image Contents