Zebra Technologies Z4M manual Initialize Memory Card, Initialize Card, Initialize Flash Memory

Page 52

Display Shows

Action/Explanation

Initialize Memory Card

CAUTION: Perform this operation only when it is necessary to erase all previously stored information from the optional memory card. Press the SETUP/EXIT key to bypass this function.

 

1.

Press the INCREMENT (+) key to select “YES.”

 

 

 

If your printer is set to require a password, you will now be

 

 

 

prompted to enter the password. Enter the password and then

 

 

 

press the SELECT key.

 

2.

The display will ask “INITIALIZE CARD?”. Press the INCREMENT (+)

 

 

key “YES.”

INITIALIZE CARD

3.

The front panel LCD will ask “ARE YOU SURE?”.

4.

Press the INCREMENT (+) key “YES” to begin initialization.

 

 

 

 

or

 

 

Press the DECREMENT (-) key “NO” to cancel the request and return to

 

 

the “INITIALIZE CARD” prompt.

 

5.

Press the SETUP/EXIT key followed by the SELECT key. If initialization

 

 

is still in process, the front panel display will flash back and forth between

 

 

the two phrases “CHECKING B: MEMORY” and “PRINTER IDLE.”

 

 

When initialization is complete, the printer will automatically exit the

 

 

configuration mode and the front panel will display “PRINTER READY.”

 

NOTE:

Depending on the amount of memory in the memory card,

 

 

 

initialization may take up to five minutes to complete.

 

 

 

Initialize Flash Memory

 

CAUTION: Perform this operation only when it is necessary to erase all

 

previously stored information from the FLASH memory. Press the

 

SETUP/EXIT key to bypass this function.

 

1.

Press the INCREMENT (+) key to select “YES.”

 

 

 

If your printer is set to require a password, you will now be prompted

 

 

 

to enter the password. Enter the password and then press the

 

 

 

SELECT key.

 

2.

The display will ask “INITIALIZE FLASH?”. Press the INCREMENT (+)

 

 

key “YES.”

INIT FLASH MEM

3.

The front panel LCD will ask “ARE YOU SURE?”.

4.

Press the INCREMENT (+) key “YES” to begin initialization.

 

 

 

 

or

 

 

Press the DECREMENT (-) key “NO” to cancel the request and return to

 

 

the “INITIALIZE FLASH” prompt.

 

5.

Press the SETUP/EXIT key followed by the SELECT key. If initialization

 

 

is still in process, the front panel display will flash back and forth between

 

 

the two phrases “CHECKING E: MEMORY” and “PRINTER IDLE.”

 

 

When initialization is complete, the printer will automatically exit the

 

 

configuration mode and the front panel will display “PRINTER READY.”

 

NOTE:

Depending on the amount of free FLASH memory, initialization may

 

 

 

take up to one minute to complete.

44

Zebra Z4M Printer User’s Guide

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Customer order # 77965L Manufacturer 77965LB Rev Zebra Z4M Printer User’s Guide Zebra Z4M Printer Zebra Z4M Printer User’s Guide Table of Contents Establishing Communication Configuration Index Hello WelcomeUnpacking and Inspection Reporting Damage Media and Ribbon RequirementsStorage Printer Power Printer Overview Calibrating the Printer PurposeTypes of Media Non-Continuous Web MediaNon-Continuous Black Mark Media Continuous MediaChoosing the Print Mode Loading the Media Positioning the Media Sensor Reflective SensorAdjusting the Reflective Sensor Loading the Ribbon Transmissive SensorAuto Calibration Operator Controls Power SwitchFront Panel Configuring the Printer Configuring the Software of Printer Driver Printing a Test LabelData Specifications Establishing CommunicationSystem Considerations InterfacesCabling Requirements Front Panel Printer BasicsFront Panel Display Front Panel Keys Key FunctionFront Panel Lights Light Status IndicationTear-Off Mode Roll Media LoadingTransmissive Sensor Printhead Assembly Dancer Cutter Mode Printhead Assembly Ribbon Sensor Cutter Value Peel-Off Mode Media supply guide Power Peel-Off Mode Backing Removal Power Rewind Mode Media Removal Fanfold Media Loading Dancer Media Ribbon Media guide Ribbon Loading Loading the RibbonZebra Z4M Printer User’s Guide Ribbon Removal Configuration Entering the Setup ModeChanging Password-Protected Parameters Leaving the Setup Mode Configuration and Calibration Sequence Setting Print ParametersDefault +10 Default +0Default Tear-off Default WebSelections Web, mark Sensor SelectPrint Width Listing Printer Information Initialize Memory Card Initialize CardInitialize Flash Memory Init Flash MEMMedia and Ribbon Sensor Calibration Sensor ProfileManual CalibrationSetting Communication Parameters Setting Parallel CommunicationsDefault Parallel Setting BaudSetting Parity Default EvenSetting Host Handshake Default XON/XOFFSetting Network ID Setting Communications ModeNetwork ID CommunicationsSelecting Prefix and Delimiter Characters Control Prefix CharacterRange 00-FF Range 00 FFSelecting ZPL Mode Default ZPL Selections ZPL II, ZPLPower-Up and Head Close Parameters Media Power-Up Default FeedLabel Positioning Parameters Backfeed SequenceBackfeed Label TOPLCD Adjust Password LevelWEB S Media S Ribbon SIP Resolution Default DynamicDefault All Default GatewayDefault English Default PermanentSave Settings LanguageRoutine Care and Adjustments CleaningCleaning the Interior Cleaning the ExteriorCleaning the Printhead and Platen Roller Cleaning the Sensors Cleaning the Power Peel-Off Module Cleaning the Value Peel-Off Module Cleaning the Cutter Module Lubrication Printhead Pressure Adjustment Pressure adjustment dials Power Rewind Media Alignment Adjustment Fuse Replacement Troubleshooting LCD Error Conditions and WarningsError condition Ribbon OUT Error condition Paper OUTError condition Head Open Error condition RibbonPrint Quality Problems General print quality issuesGray lines on blank labels with no consistent pattern Wrinkled ribbonCommunications Problems CalibrationZebra Z4M Printer User’s Guide Power-On Self Test Printer DiagnosticsAdditional Printer Self Tests Cancel Key Self Test Pause Key Self Test Feed Key Self Test Loading Factory Defaults Communications Diagnostics TestZebra Z4M Printer User’s Guide Specifications General SpecificationsPrinting Specifications Ribbon SpecificationsMedia Specifications OptionsZebra Programming Language ZPL Bar CodesAC Power Cord Power Line Cord SpecificationsZebra Z4M Printer User’s Guide Printer Interface Technical Information AppendixSerial Data Communications RS-232 Interface Hardware Control Signal Descriptions RS-485 Interface Parallel Data Communications Parallel InterfaceZebra Z4M Printer User’s Guide Index Zebra Z4M Printer User’s Guide Zebra Z4M Printer User’s Guide Zebra Z4M Printer User’s Guide

Z4M specifications

Zebra Technologies has long been a prominent name in the field of printing solutions, and the Z4M label printer stands out as a robust device well-suited for various industrial applications. Known for its reliability and high-performance capabilities, the Z4M is designed to meet the demanding needs of environments such as manufacturing, warehousing, and retail.

One of the key features of the Zebra Z4M is its thermal transfer printing technology. This method provides superior print quality for barcodes, text, and graphics, ensuring that critical information is clearly legible. The printer is capable of producing labels at a speed of up to 6 inches per second, increasing efficiency and productivity in busy settings. With a resolution of up to 203 dpi, it offers crisp, clear printing that is essential for accurate inventory management and tracking.

The Z4M printer is designed with versatility in mind. It supports a wide range of media types including paper, synthetic, and tags, enabling users to print labels of various sizes and materials. The maximum print width of 4 inches allows for the creation of large labels that can accommodate more information, which is particularly useful for shipping and logistics applications.

Connectivity options play a crucial role in modern printing solutions, and the Z4M does not disappoint. It comes equipped with standard parallel, serial, and USB interfaces, and offers optional Ethernet and Wi-Fi capabilities. This allows for seamless integration into existing systems and ensures that printers can be easily networked for shared use.

Built for durability, the Z4M features a sturdy metal construction that can withstand the rigors of industrial environments. Its compact design makes it easy to place in various locations, while the user-friendly interface simplifies setup and operation. The LCD screen provides clear status updates, and the printer's intuitive controls make it accessible for operators of all skill levels.

Another notable characteristic of the Z4M is its advanced software compatibility. It supports Zebra's programming languages including ZPL and EPL, making it customizable for diverse applications. This flexibility ensures that businesses can maximize the printer's functionality according to their specific needs.

Overall, the Zebra Technologies Z4M is a versatile and reliable label printer that combines quality, speed, and durability, making it an excellent choice for businesses looking to enhance their labeling processes.
Top Page Image Contents