Zebra Technologies Z4M manual Default English, Language, Default Permanent, Save Settings

Page 62

	Display Shows	Action/Explanation
		Selecting the Display Language Press the INCREMENT (+) or DECREMENT (-)
		key to display other choices.
		Default: English
	LANGUAGE	Selections: English, Spanish, French, German, Italian, Norwegian,
		Portuguese, Swedish, Danish, Spanish 2, Dutch, Finnish, Japan
		This parameter allows you to change the language used on the front panel
		display.

You have now completed the entire configuration and calibration sequence. You may either press the SELECT key or the SETUP/EXIT key.

	You are now back at the first parameter in the configuration sequence.
DARKNESS	NOTE: If you pressed the SELECT key but are through programming the
	printer configuration, you may press the SETUP/EXIT key and continue
	with the “SAVE SETTINGS” function.

	Save Settings Press the INCREMENT (+) or DECREMENT (-) key to display
	other choices.
	Default: Permanent
	Selections: Permanent, temporary, cancel, load defaults, load last save.
	This display appears when you attempt to exit the configuration mode.
	• Permanent: Permanently saves the changes, even when printer power is
SAVE SETTINGS	turned off.
	• Temporary: Saves the changes until changed again or until power is turned
	off.
	• Cancel: Cancels all changes since you entered the configuration mode
	except for darkness and tear-off position (if they were changed).
	• Load defaults: Loads factory defaults.
	• Load last save: Loads the values from the last permanent save.

	Press the SETUP/EXIT key to activate the displayed choice.
PRINTER READY	You have exited the configuration and calibration sequence and are now ready
	for normal printer operation.

54	Zebra Z4M Printer User’s Guide

Image 62

Contents

Customer order # 77965L Manufacturer 77965LB Rev Zebra Z4M Printer User’s Guide Zebra Z4M Printer Zebra Z4M Printer User’s Guide Table of Contents Establishing Communication Configuration Index Unpacking and Inspection WelcomeHello Storage Media and Ribbon RequirementsReporting Damage Printer Power Printer Overview Calibrating the Printer PurposeTypes of Media Non-Continuous Web MediaNon-Continuous Black Mark Media Continuous MediaChoosing the Print Mode Loading the Media Positioning the Media Sensor Reflective SensorAdjusting the Reflective Sensor Loading the Ribbon Transmissive SensorAuto Calibration Front Panel Power SwitchOperator Controls Configuring the Printer Configuring the Software of Printer Driver Printing a Test LabelSystem Considerations Data SpecificationsEstablishing Communication InterfacesCabling Requirements Front Panel Display Printer BasicsFront Panel Front Panel Keys Key FunctionFront Panel Lights Light Status IndicationTear-Off Mode Roll Media LoadingTransmissive Sensor Printhead Assembly Dancer Cutter Mode Printhead Assembly Ribbon Sensor Cutter Value Peel-Off Mode Media supply guide Power Peel-Off Mode Backing Removal Power Rewind Mode Media Removal Fanfold Media Loading Dancer Media Ribbon Media guide Ribbon Loading Loading the RibbonZebra Z4M Printer User’s Guide Ribbon Removal Configuration Entering the Setup ModeChanging Password-Protected Parameters Leaving the Setup Mode Default +10 Configuration and Calibration SequenceSetting Print Parameters Default +0Selections Web, mark Default Tear-offDefault Web Sensor SelectPrint Width Listing Printer Information Initialize Flash Memory Initialize Memory CardInitialize Card Init Flash MEMManual Media and Ribbon Sensor CalibrationSensor Profile CalibrationDefault Parallel Setting Communication ParametersSetting Parallel Communications Setting BaudSetting Host Handshake Setting ParityDefault Even Default XON/XOFFNetwork ID Setting Network IDSetting Communications Mode CommunicationsRange 00-FF Selecting Prefix and Delimiter CharactersControl Prefix Character Range 00 FF Power-Up and Head Close Parameters Media Power-Up Selecting ZPL Mode Default ZPL Selections ZPL II, ZPL Default FeedBackfeed Label Positioning ParametersBackfeed Sequence Label TOPWEB S Media S LCD AdjustPassword Level Ribbon SDefault All IP ResolutionDefault Dynamic Default GatewaySave Settings Default EnglishDefault Permanent LanguageRoutine Care and Adjustments CleaningCleaning the Printhead and Platen Roller Cleaning the ExteriorCleaning the Interior Cleaning the Sensors Cleaning the Power Peel-Off Module Cleaning the Value Peel-Off Module Cleaning the Cutter Module Lubrication Printhead Pressure Adjustment Pressure adjustment dials Power Rewind Media Alignment Adjustment Fuse Replacement Error condition Ribbon OUT TroubleshootingLCD Error Conditions and Warnings Error condition Paper OUTError condition Head Open Error condition RibbonPrint Quality Problems General print quality issuesGray lines on blank labels with no consistent pattern Wrinkled ribbonCommunications Problems CalibrationZebra Z4M Printer User’s Guide Additional Printer Self Tests Printer DiagnosticsPower-On Self Test Cancel Key Self Test Pause Key Self Test Feed Key Self Test Loading Factory Defaults Communications Diagnostics TestZebra Z4M Printer User’s Guide Specifications General SpecificationsPrinting Specifications Ribbon SpecificationsMedia Specifications OptionsZebra Programming Language ZPL Bar CodesAC Power Cord Power Line Cord SpecificationsZebra Z4M Printer User’s Guide Serial Data Communications AppendixPrinter Interface Technical Information RS-232 Interface Hardware Control Signal Descriptions RS-485 Interface Parallel Data Communications Parallel InterfaceZebra Z4M Printer User’s Guide Index Zebra Z4M Printer User’s Guide Zebra Z4M Printer User’s Guide Zebra Z4M Printer User’s Guide