Zebra Technologies Z4M manual Print Quality Problems, General print quality issues

Page 77

Warning CUTTER JAM

Problem

Solution

 

Turn off the printer power and unplug the printer.

Cutter blade is in the media path.

Inspect the cutter module for debris and clean as

 

needed following the cleaning instructions on page 60.

 

 

OUT OF MEMORY*

Problem

Solution

 

Insufficient DRAM for the label length, downloaded

 

fonts/graphics, and images.

*There is not enough memory to perform

 

Ensure that the device, such as FLASH memory or

the function shown on the second line of

PCMCIA card, is installed and not write protected or full.

the error message.

 

Ensure that the data is not directed to a device that is

 

 

not installed or available.

 

 

Print Quality Problems

General print quality issues

Problem

Solution

You are using an incorrect media and

Consult your authorized Zebra reseller/distributor for

ribbon combination for your application.

information and advice.

 

 

The printer is set at the incorrect print

For optimal print quality, set the print speed to the

lowest possible setting via ZPL II, the driver, or the

speed.

software.

 

 

 

The printer is set at the incorrect darkness

For optimal print quality, set the darkness to the lowest

possible setting via the front panel, the driver, or the

level.

software.

 

 

 

The printhead is dirty.

Clean the printhead according to the instructions on

page 56.

 

 

 

There is light printing (or no printing) on

The pressure adjustment dials need to be adjusted.

the left or right side of the label or the

Follow the printhead pressure adjustment instructions

printed image is not sharp.

on page 62.

 

 

Zebra Z4M Printer User’s Guide

69

Page 76 Page 78
Image 77
Page 76 Page 78
Contents Customer order # 77965L Manufacturer 77965LB Rev Zebra Z4M Printer User’s Guide Zebra Z4M Printer Zebra Z4M Printer User’s Guide Table of Contents Establishing Communication Configuration Index Unpacking and Inspection WelcomeHello Storage Media and Ribbon RequirementsReporting Damage Printer Power Printer Overview Purpose Calibrating the PrinterNon-Continuous Web Media Types of MediaContinuous Media Non-Continuous Black Mark MediaChoosing the Print Mode Loading the Media Reflective Sensor Positioning the Media SensorAdjusting the Reflective Sensor Transmissive Sensor Loading the RibbonAuto Calibration Front Panel Power SwitchOperator Controls Configuring the Printer Printing a Test Label Configuring the Software of Printer DriverEstablishing Communication Data SpecificationsSystem Considerations InterfacesCabling Requirements Front Panel Display Printer BasicsFront Panel Key Function Front Panel KeysLight Status Indication Front Panel LightsRoll Media Loading Tear-Off ModeTransmissive Sensor Printhead Assembly Dancer Cutter Mode Printhead Assembly Ribbon Sensor Cutter Value Peel-Off Mode Media supply guide Power Peel-Off Mode Backing Removal Power Rewind Mode Media Removal Fanfold Media Loading Dancer Media Ribbon Media guide Loading the Ribbon Ribbon LoadingZebra Z4M Printer User’s Guide Ribbon Removal Entering the Setup Mode ConfigurationChanging Password-Protected Parameters Leaving the Setup Mode Setting Print Parameters Configuration and Calibration SequenceDefault +10 Default +0Default Web Default Tear-offSelections Web, mark Sensor SelectPrint Width Listing Printer Information Initialize Card Initialize Memory CardInitialize Flash Memory Init Flash MEMSensor Profile Media and Ribbon Sensor CalibrationManual CalibrationSetting Parallel Communications Setting Communication ParametersDefault Parallel Setting BaudDefault Even Setting ParitySetting Host Handshake Default XON/XOFFSetting Communications Mode Setting Network IDNetwork ID CommunicationsControl Prefix Character Selecting Prefix and Delimiter CharactersRange 00-FF Range 00 FFDefault ZPL Selections ZPL II, ZPL Selecting ZPL ModePower-Up and Head Close Parameters Media Power-Up Default FeedBackfeed Sequence Label Positioning ParametersBackfeed Label TOPPassword Level LCD AdjustWEB S Media S Ribbon SDefault Dynamic IP ResolutionDefault All Default GatewayDefault Permanent Default EnglishSave Settings LanguageCleaning Routine Care and AdjustmentsCleaning the Printhead and Platen Roller Cleaning the ExteriorCleaning the Interior Cleaning the Sensors Cleaning the Power Peel-Off Module Cleaning the Value Peel-Off Module Cleaning the Cutter Module Lubrication Printhead Pressure Adjustment Pressure adjustment dials Power Rewind Media Alignment Adjustment Fuse Replacement LCD Error Conditions and Warnings TroubleshootingError condition Ribbon OUT Error condition Paper OUTError condition Ribbon Error condition Head OpenGeneral print quality issues Print Quality ProblemsWrinkled ribbon Gray lines on blank labels with no consistent patternCalibration Communications ProblemsZebra Z4M Printer User’s Guide Additional Printer Self Tests Printer DiagnosticsPower-On Self Test Cancel Key Self Test Pause Key Self Test Feed Key Self Test Communications Diagnostics Test Loading Factory DefaultsZebra Z4M Printer User’s Guide General Specifications SpecificationsRibbon Specifications Printing SpecificationsOptions Media SpecificationsBar Codes Zebra Programming Language ZPLPower Line Cord Specifications AC Power CordZebra Z4M Printer User’s Guide Serial Data Communications AppendixPrinter Interface Technical Information RS-232 Interface Hardware Control Signal Descriptions RS-485 Interface Parallel Interface Parallel Data CommunicationsZebra Z4M Printer User’s Guide Index Zebra Z4M Printer User’s Guide Zebra Z4M Printer User’s Guide Zebra Z4M Printer User’s Guide

Z4M specifications

Zebra Technologies has long been a prominent name in the field of printing solutions, and the Z4M label printer stands out as a robust device well-suited for various industrial applications. Known for its reliability and high-performance capabilities, the Z4M is designed to meet the demanding needs of environments such as manufacturing, warehousing, and retail.

One of the key features of the Zebra Z4M is its thermal transfer printing technology. This method provides superior print quality for barcodes, text, and graphics, ensuring that critical information is clearly legible. The printer is capable of producing labels at a speed of up to 6 inches per second, increasing efficiency and productivity in busy settings. With a resolution of up to 203 dpi, it offers crisp, clear printing that is essential for accurate inventory management and tracking.

The Z4M printer is designed with versatility in mind. It supports a wide range of media types including paper, synthetic, and tags, enabling users to print labels of various sizes and materials. The maximum print width of 4 inches allows for the creation of large labels that can accommodate more information, which is particularly useful for shipping and logistics applications.

Connectivity options play a crucial role in modern printing solutions, and the Z4M does not disappoint. It comes equipped with standard parallel, serial, and USB interfaces, and offers optional Ethernet and Wi-Fi capabilities. This allows for seamless integration into existing systems and ensures that printers can be easily networked for shared use.

Built for durability, the Z4M features a sturdy metal construction that can withstand the rigors of industrial environments. Its compact design makes it easy to place in various locations, while the user-friendly interface simplifies setup and operation. The LCD screen provides clear status updates, and the printer's intuitive controls make it accessible for operators of all skill levels.

Another notable characteristic of the Z4M is its advanced software compatibility. It supports Zebra's programming languages including ZPL and EPL, making it customizable for diverse applications. This flexibility ensures that businesses can maximize the printer's functionality according to their specific needs.

Overall, the Zebra Technologies Z4M is a versatile and reliable label printer that combines quality, speed, and durability, making it an excellent choice for businesses looking to enhance their labeling processes.
Top Page Image Contents