Zebra Technologies S-300 manual Lubrication, AC Power Fuse Replacement

Page 40

Routine Care and Adjustment

V.Reinstall the Cutter Module.

1.See Figure 19. Position the Cutter Module above the Cutter Mounting Posts. Press down on the Cutter Module until the Mounting Slots engage the Mounting Posts on the printer.

2.See Figure 18. Tighten the Mounting Screw in a clockwise direction to hold the Cutter Module in Position.

3.See Figure 18. Position the Cutter Cable Connector so the flat side of the connector faces away from the printer, then insert it up into the mating connector on the Cutter Module.

4.Replace the Cutter Catch Tray onto the two mounting posts located on the front of the Cutter Module.

VI. Test the Cutter Operation.

1.If necessary, reload ribbon and label stock into the printer, then close the printer’s Front Door and Media Access Door.

NOTE: When loading media, make sure the end of the label is positioned on top of the Platen Roller, then close the Printhead Latch.

2.When the printer is turned ON, the Cutter Module will cycle through one cutting operation and be ready to print labels.

3.OPTIONAL: Hold in the PAUSE key while turning the printer’s AC power ON. When the Power ON Self Test begins (all lights ON), release the PAUSE key. When the Power ON Self Test ends, the printer will automatically print test labels which the Cutter Module will automatically cut.

End of Cutter Cleaning Procedure.

Lubrication

No lubricating agents of any kind are required on this printer. Some commercially available lubricants will damage the finish if used.

AC Power Fuse Replacement

A user-replaceable AC Power Fuse is located just to the left of the Power ON/OFF Switch. (See Figure 11 on page 19.) For a 110 VAC installation, the replacement Fuse is a 3AG Fast Blow style rated at 5 Amp/250VAC. For a 220 VAC installation, the Fuse is the same style but rated at 3 Amp/250VAC .

Before replacing the Fuse, turn the AC Power Switch OFF and unplug the AC Power Cable.

To replace the Fuse, insert the tip of a flathead screwdriver into the slot in the end of the Fuse Holder End Cap. Press in slightly on the End Cap and turn the screwdriver slightly counterclockwise. This will disengage the End Cap from the Fuse Holder and permit removal of the Fuse. To install a new fuse, reverse the sequence.

32

Image 40
Contents User’s Guide Proprietary Statement Warranty Information Warranty Information Zebra Software License AgreementMedia Calibration Adjust the Print Darkness AC Power ON/OFF Switch Fro FEEDServicesKey and Pause Key RS-232 Cabling Requirements Unpacking Reporting DamagePrinter Power Up Getting StartedSite Requirements Storage and ReshippingAC Power Cable Voltage SelectionCommunications Tear- Off Mode Media Loading T t i n g S t a r t e dMedia and Ribbon Loading MediaExternal Rewind Mode Media Loading Cutter Mode Media Loading Cutter Option RequiredFanfold Media Loading Fanfold Media Loading in Tear-Off Mode Peel-Off Mode Media LoadingPeel-Off Option Required Removing the Label Backing Material Peel Off Option Required Non-Continuous Media Adjusting the Media SensorContinuous Media Adjusting the Ribbon Supply Spindle Ribbon LoadingRibbon Supply Spindle Normal Position Ribbon Supply Spindle Low-Tension PositionRibbon Removal Loading the RibbonConfiguration and Calibration Option Switch SettingsSwitch Baud Rate SwitchConfiguration Mode Media CalibrationAdjust the Media Rest Position Adjust the Print DarknessAdjust the Position of the Top of the Label Getting Started Operating Your Zebra Stripe Printer Tear-Off ModePrinter Operating Modes Operation AC Power ON/OFF SwitchOperator Controls AC Power ON/OFF Switch Front Panel Lights Front Panel KeysPrinter Status Sensors Sensor What it monitors How it worksBacking Rewind Spindle Full Sensor Position Format 1 Simple Text and a Barcode Sample ZPL II Label FormatsType this label format Format 3 Using a Serialized Data Field Format 2 Saving a Label Format As a Graphic ImageLine Type this label format You’ll get this printout Type this label format You’ll get this printoutCleaning Cleaning the ExteriorCleaning the Interior Preventive Maintenance KitRoutine Care and Adjustment Cleaning the PrintheadCutter Module and Catch Tray Location This procedure is on the next Cutter Module Disassembly This procedure is on Reassembled Cutter Module AC Power Fuse Replacement LubricationMechanical Adjustments Print Quality AdjustmentsToggle Pressure Adjustment Toggle Pressure AdjustmentMedia Sensor Position Adjustment Ribbon Supply Spindle AdjustmentBattery Replacement Troubleshooting and Diagnostics Troubleshooting TableTroubleshooting and Diagnostics FlashingTroubleshooting and Diagnostics Troubleshooting and Diagnostics Power-On Self Test Printer DiagnosticsAdditional Printer Self Tests Cancel Key Self Test Pause Key Self TestFeed Key Self Test Pause Key Self Test PrintoutMode Key Self Test Extended Printer DiagnosticsFeed Key and Pause Key Page Page Options*Factory-Installed StandardPrinterFonts DefaultPrinterFonts6Dots/mm Page Ard BitmapSmoothFontsPointSizeExamples How to Reach Us Zebra Technical Support Bulletin Board ServiceTechnical Support Zebra’s Corporate OfficesTechnical Support Service via Telephone Support ServicesTechnical Support via Mail or Fax Zebra Technologies Corporation Service Form Product Service and Support Programs Extended Factory Service AgreementThird Party Support And Maintenance Select The Program That Fits Your BusinessUser Self Maintenance Zebra Factory ServicesWang Customer Services Division International Service and Support Zebra Training Programs Operations and Maintenance Courses Course Name Printers CoveredBar Codes at Work LabelingSupport Services Adjusting the Printhead Printhead Position Adjustment ProcedurePrint Quality Adjustment AppendixSignal Levels Hardware Control Signal DescriptionsPrinter Interface Technical Information RS-232 InterfaceInterconnect To DTE Devices RS-232 Cabling RequirementsInterconnect To DCE Devices Parallel Interface Parallel Cabling RequirementsSignal Descriptions Pin No Parallel Connector PinoutGlossary Glossary Index Index