Zebra Technologies S-300 manual Index

Page 80

Index

Media Calibration, 14

Media Guide, 5

Media Sensors, 10, 26

Media Supply Guide, 5

MODE Key, 20

N

Null Modem, 67

O

Operating Modes

Cutter, 18

Peel-Off, 17

Rewind (External), 6, 18

Tear-Off, 5, 17

Operator Controls, 46

Option Switches, 13

Optional Fonts, 50

P

Parallel Interface, 68

Parity, 13

PAUSE Key, 20

Power ON/OFF Switch, 18

Power Up, 2

Preventive Maintenance Kit, 25

Print Element, 26

Printer Diagnostics, 41

Printer Specifications, 45

Printer Status Sensors, 21

Backing Rewind Spindle Full Sensor, 21

Label Available Sensor, 21

Media Sensor, 21

Printhead Sensor, 21

Ribbon Sensor, 21

Printer Test, 13

Printhead Assembly, 63

R

Reporting Damage, 1

Reshipping, 2

Ribbon Loading, 12

Ribbon Release Button, 12

Ribbon Removal, 12

Ribbon Supply Spindle, 12

Ribbon Takeup Spindle, 12

RTS (Request To Send), 66-67, 69

RXD (Receive Data), 66

S

Self Tests

CANCEL Key, 42

FEED Key, 43

FEED Key and PAUSE Key, 44

MODE Key, 44

PAUSE Key, 42

Power ON, 41

Serial Communication Port, 67

Shipping Container, 2

Shipping Damage, 1

Signal Ground, 66

Specifications, 45

Standard Fonts, 48

Storage and Reshipping, 2

T

Tear/Peel-Off Plate, 17

Troubleshooting, 37

TXD (Transmit Data), 66

U

Unpacking, 1

W

Warning

AC Voltage, 2

Earth Ground, 3

Equipment Safety, 3

Personnel Safety, 3

X

XON/XOFF Data Control, 13

Z

ZPL II Instructions

Label Length (^LL), 10

74

Image 80

Contents User’s Guide Proprietary Statement Warranty Information Warranty Information Zebra Software License AgreementMedia Calibration Adjust the Print Darkness AC Power ON/OFF Switch Fro FEEDServicesKey and Pause Key RS-232 Cabling Requirements Unpacking Reporting DamagePrinter Power Up Getting StartedSite Requirements Storage and ReshippingAC Power Cable Voltage SelectionCommunications Tear- Off Mode Media Loading T t i n g S t a r t e dMedia and Ribbon Loading MediaFanfold Media Loading Cutter Mode Media Loading Cutter Option RequiredExternal Rewind Mode Media Loading Fanfold Media Loading in Tear-Off Mode Peel-Off Mode Media LoadingPeel-Off Option Required Removing the Label Backing Material Peel Off Option Required Continuous Media Adjusting the Media SensorNon-Continuous Media Adjusting the Ribbon Supply Spindle Ribbon LoadingRibbon Supply Spindle Normal Position Ribbon Supply Spindle Low-Tension PositionRibbon Removal Loading the RibbonConfiguration and Calibration Option Switch SettingsSwitch Baud Rate SwitchConfiguration Mode Media CalibrationAdjust the Position of the Top of the Label Adjust the Print DarknessAdjust the Media Rest Position Getting Started Printer Operating Modes Tear-Off ModeOperating Your Zebra Stripe Printer Operator Controls AC Power ON/OFF SwitchOperation AC Power ON/OFF Switch Front Panel Lights Front Panel KeysPrinter Status Sensors Sensor What it monitors How it worksBacking Rewind Spindle Full Sensor Position Type this label format Sample ZPL II Label FormatsFormat 1 Simple Text and a Barcode Format 3 Using a Serialized Data Field Format 2 Saving a Label Format As a Graphic ImageLine Type this label format You’ll get this printout Type this label format You’ll get this printoutCleaning Cleaning the ExteriorCleaning the Interior Preventive Maintenance KitRoutine Care and Adjustment Cleaning the PrintheadCutter Module and Catch Tray Location This procedure is on the next Cutter Module Disassembly This procedure is on Reassembled Cutter Module AC Power Fuse Replacement LubricationMechanical Adjustments Print Quality AdjustmentsToggle Pressure Adjustment Toggle Pressure AdjustmentMedia Sensor Position Adjustment Ribbon Supply Spindle AdjustmentBattery Replacement Troubleshooting and Diagnostics Troubleshooting TableTroubleshooting and Diagnostics FlashingTroubleshooting and Diagnostics Troubleshooting and Diagnostics Additional Printer Self Tests Printer DiagnosticsPower-On Self Test Cancel Key Self Test Pause Key Self TestFeed Key Self Test Pause Key Self Test PrintoutFeed Key and Pause Key Extended Printer DiagnosticsMode Key Self Test Page Page Options*Factory-Installed StandardPrinterFonts DefaultPrinterFonts6Dots/mm Page Ard BitmapSmoothFontsPointSizeExamples How to Reach Us Zebra Technical Support Bulletin Board ServiceTechnical Support Zebra’s Corporate OfficesTechnical Support via Mail or Fax Support ServicesTechnical Support Service via Telephone Zebra Technologies Corporation Service Form Product Service and Support Programs Extended Factory Service AgreementThird Party Support And Maintenance Select The Program That Fits Your BusinessWang Customer Services Division Zebra Factory ServicesUser Self Maintenance International Service and Support Zebra Training Programs Operations and Maintenance Courses Course Name Printers CoveredBar Codes at Work LabelingSupport Services Adjusting the Printhead Printhead Position Adjustment ProcedurePrint Quality Adjustment AppendixSignal Levels Hardware Control Signal DescriptionsPrinter Interface Technical Information RS-232 InterfaceInterconnect To DCE Devices RS-232 Cabling RequirementsInterconnect To DTE Devices Parallel Interface Parallel Cabling RequirementsSignal Descriptions Pin No Parallel Connector PinoutGlossary Glossary Index Index