Zebra Technologies S-300 manual Voltage Selection, AC Power Cable

Page 11

Getting Started

Voltage Selection

The Stripe is available from the factory preset for either 100-120 VAC electrical power or 220-240 VAC electrical power. Refer to the product label on the back of the printer and make sure that the unit is properly configured for your power requirements.

AC Power Cable

The AC Power Cable has a three-prong female connector on one end. See Figure 2. This connector must be plugged into the mating connector on the left side of the printer. See Figure 1.

The electrical connection at the other end of the AC Power Cable will be one of the following:

∙US Standard 110 VAC three-prong plug

∙Great Britain Standard 220 VAC three-prong plug

∙European Standard 220 VAC three-prong plug

WARNING!! For personnel and equipment safety, always use a three-prong plug with an earth ground connection.

Insure that the AC Power ON/OFF Switch is in the OFF (0) position before connecting the AC Power Cable to a nearby electrical outlet.

1

Figure 1 Cable Connections

Figure 2 AC Power Cable

3

Image 11

Contents User’s Guide Proprietary Statement Warranty Information Zebra Software License Agreement Warranty InformationMedia Calibration Adjust the Print Darkness AC Power ON/OFF Switch Fro FEEDServicesKey and Pause Key RS-232 Cabling Requirements Reporting Damage UnpackingStorage and Reshipping Printer Power UpGetting Started Site RequirementsVoltage Selection AC Power CableCommunications Loading Media Tear- Off Mode Media LoadingT t i n g S t a r t e d Media and RibbonFanfold Media Loading Cutter Mode Media Loading Cutter Option RequiredExternal Rewind Mode Media Loading Fanfold Media Loading in Tear-Off Mode Peel-Off Mode Media LoadingPeel-Off Option Required Removing the Label Backing Material Peel Off Option Required Continuous Media Adjusting the Media SensorNon-Continuous Media Ribbon Supply Spindle Low-Tension Position Adjusting the Ribbon Supply SpindleRibbon Loading Ribbon Supply Spindle Normal PositionLoading the Ribbon Ribbon RemovalSwitch Configuration and CalibrationOption Switch Settings Switch Baud RateMedia Calibration Configuration ModeAdjust the Position of the Top of the Label Adjust the Print DarknessAdjust the Media Rest Position Getting Started Printer Operating Modes Tear-Off ModeOperating Your Zebra Stripe Printer Operator Controls AC Power ON/OFF SwitchOperation AC Power ON/OFF Switch Front Panel Keys Front Panel LightsSensor What it monitors How it works Printer Status SensorsBacking Rewind Spindle Full Sensor Position Type this label format Sample ZPL II Label FormatsFormat 1 Simple Text and a Barcode Type this label format You’ll get this printout Format 3 Using a Serialized Data FieldFormat 2 Saving a Label Format As a Graphic Image Line Type this label format You’ll get this printoutPreventive Maintenance Kit CleaningCleaning the Exterior Cleaning the InteriorCleaning the Printhead Routine Care and AdjustmentCutter Module and Catch Tray Location This procedure is on the next Cutter Module Disassembly This procedure is on Reassembled Cutter Module Lubrication AC Power Fuse ReplacementPrint Quality Adjustments Mechanical AdjustmentsToggle Pressure Adjustment Toggle Pressure AdjustmentRibbon Supply Spindle Adjustment Media Sensor Position AdjustmentBattery Replacement Troubleshooting Table Troubleshooting and DiagnosticsFlashing Troubleshooting and DiagnosticsTroubleshooting and Diagnostics Troubleshooting and Diagnostics Additional Printer Self Tests Printer DiagnosticsPower-On Self Test Pause Key Self Test Cancel Key Self TestPause Key Self Test Printout Feed Key Self TestFeed Key and Pause Key Extended Printer DiagnosticsMode Key Self Test Page Page Options*Factory-Installed StandardPrinterFonts DefaultPrinterFonts6Dots/mm Page Ard BitmapSmoothFontsPointSizeExamples Zebra’s Corporate Offices How to Reach UsZebra Technical Support Bulletin Board Service Technical SupportTechnical Support via Mail or Fax Support ServicesTechnical Support Service via Telephone Zebra Technologies Corporation Service Form Select The Program That Fits Your Business Product Service and Support ProgramsExtended Factory Service Agreement Third Party Support And MaintenanceWang Customer Services Division Zebra Factory ServicesUser Self Maintenance International Service and Support Zebra Training Programs Course Name Printers Covered Operations and Maintenance CoursesLabeling Bar Codes at WorkSupport Services Printhead Position Adjustment Procedure Adjusting the PrintheadAppendix Print Quality AdjustmentRS-232 Interface Signal LevelsHardware Control Signal Descriptions Printer Interface Technical InformationInterconnect To DCE Devices RS-232 Cabling RequirementsInterconnect To DTE Devices Parallel Cabling Requirements Parallel InterfacePin No Parallel Connector Pinout Signal DescriptionsGlossary Glossary Index Index