Zebra Technologies S-300 manual Feed Key Self Test, Pause Key Self Test Printout

Page 51

Troubleshooting and Diagnostics

FEED Key Self Test

The results of this self test will be used to determine the best Darkness Setting for a specific media/ribbon combination.

See Figure 29. The FEED Key Self Test labels will print at various plus or minus Darkness settings relative to the current darkness setting. The operator inspects these printouts and determines which printout has the best darkness setting.

The value on that printout is added to (plus) or subtracted from (minus) the current Darkness value.

To make the change, you need to adjust the Print Darkness (as described in Chapter 1).

1.Press the MODE Key.

2.If the value on your FEED Key Self Test Printout is a plus value, press UP the appropriate number of times. Otherwise, press DOWN to enter a minus value.

3.Press the MODE Key three (3) times.

4.Press PAUSE.

4

Alternatively, increments to the actual Darkness value can be programmed into the label formats sent to the printer. To see the actual value of the current darkness setting, perform a CANCEL Key Self Test: the value will print on the Configuration Printout.

Figure 28 PAUSE Key Self Test Printout

Figure 29 FEED Key Self Test Printout

43

Image 51

Contents User’s Guide Proprietary Statement Warranty Information Zebra Software License Agreement Warranty InformationMedia Calibration Adjust the Print Darkness AC Power ON/OFF Switch Fro FEEDServicesKey and Pause Key RS-232 Cabling Requirements Reporting Damage UnpackingStorage and Reshipping Printer Power UpGetting Started Site RequirementsVoltage Selection AC Power CableCommunications Loading Media Tear- Off Mode Media LoadingT t i n g S t a r t e d Media and RibbonCutter Mode Media Loading Cutter Option Required External Rewind Mode Media LoadingFanfold Media Loading Fanfold Media Loading in Tear-Off Mode Peel-Off Mode Media LoadingPeel-Off Option Required Removing the Label Backing Material Peel Off Option Required Adjusting the Media Sensor Non-Continuous MediaContinuous Media Ribbon Supply Spindle Low-Tension Position Adjusting the Ribbon Supply SpindleRibbon Loading Ribbon Supply Spindle Normal PositionLoading the Ribbon Ribbon RemovalSwitch Configuration and CalibrationOption Switch Settings Switch Baud RateMedia Calibration Configuration ModeAdjust the Print Darkness Adjust the Media Rest PositionAdjust the Position of the Top of the Label Getting Started Tear-Off Mode Operating Your Zebra Stripe PrinterPrinter Operating Modes AC Power ON/OFF Switch OperationOperator Controls AC Power ON/OFF Switch Front Panel Keys Front Panel LightsSensor What it monitors How it works Printer Status SensorsBacking Rewind Spindle Full Sensor Position Sample ZPL II Label Formats Format 1 Simple Text and a BarcodeType this label format Type this label format You’ll get this printout Format 3 Using a Serialized Data FieldFormat 2 Saving a Label Format As a Graphic Image Line Type this label format You’ll get this printoutPreventive Maintenance Kit CleaningCleaning the Exterior Cleaning the InteriorCleaning the Printhead Routine Care and AdjustmentCutter Module and Catch Tray Location This procedure is on the next Cutter Module Disassembly This procedure is on Reassembled Cutter Module Lubrication AC Power Fuse ReplacementPrint Quality Adjustments Mechanical AdjustmentsToggle Pressure Adjustment Toggle Pressure AdjustmentRibbon Supply Spindle Adjustment Media Sensor Position AdjustmentBattery Replacement Troubleshooting Table Troubleshooting and DiagnosticsFlashing Troubleshooting and DiagnosticsTroubleshooting and Diagnostics Troubleshooting and Diagnostics Printer Diagnostics Power-On Self TestAdditional Printer Self Tests Pause Key Self Test Cancel Key Self TestPause Key Self Test Printout Feed Key Self TestExtended Printer Diagnostics Mode Key Self TestFeed Key and Pause Key Page Page Options*Factory-Installed StandardPrinterFonts DefaultPrinterFonts6Dots/mm Page Ard BitmapSmoothFontsPointSizeExamples Zebra’s Corporate Offices How to Reach UsZebra Technical Support Bulletin Board Service Technical SupportSupport Services Technical Support Service via TelephoneTechnical Support via Mail or Fax Zebra Technologies Corporation Service Form Select The Program That Fits Your Business Product Service and Support ProgramsExtended Factory Service Agreement Third Party Support And MaintenanceZebra Factory Services User Self MaintenanceWang Customer Services Division International Service and Support Zebra Training Programs Course Name Printers Covered Operations and Maintenance CoursesLabeling Bar Codes at WorkSupport Services Printhead Position Adjustment Procedure Adjusting the PrintheadAppendix Print Quality AdjustmentRS-232 Interface Signal LevelsHardware Control Signal Descriptions Printer Interface Technical InformationRS-232 Cabling Requirements Interconnect To DTE DevicesInterconnect To DCE Devices Parallel Cabling Requirements Parallel InterfacePin No Parallel Connector Pinout Signal DescriptionsGlossary Glossary Index Index