Zebra Technologies RW 420, RW 220 manual Getting Ready to Print, Battery Safety, Charger Safety

Page 11

Getting Ready to Print

Battery Safety

The Battery Packs used on Zebra Mobile Printers contain a great deal of energy and can cause personal injury or start a fire if used improperly or carelessly. Please observe the fol- lowing safety practices:

Caution • Avoid accidental short circuiting of any battery. Allowing battery terminals to contact conductive material will create a short circuit which could cause burns and other injuries or could start a fire.

Caution • Batteries can explode or catch fire if improperly charged

or exposed to high temperatures or fire. Do not disassemble, crush or expose batteries to water.

Caution • Use of any charger not approved specifically by Zebra for use with its batteries could cause damage to the battery pack or the printer and will void the warranty.

Read carefully and always observe the safety guidelines for Li-ion batteries provided with each Battery Pack.

Charger Safety

Do not place the LI72-4 Quad Charger in locations where liquids or metallic objects may be dropped into the charging bays.

Use care in locating either the LI72 Single Charger or the LI72-4 Quad Charger. Do not block the ventilating slots on the top and bottom covers. Ensure that the Charger is plugged into a power source which won’t accidently be turned off if you will be charging batteries overnight.

Required Regulatory Text for Argentina

Only certified adaptors with the following electrical characteristics shall be used. The use of different adaptors could damage the device, present hazards to the user and declare the correspondent guaranty void.

LI72:	Input ratings: 100-240 VAC 50/60Hz 200mA., Class 2
	Output ratings: 8.4 VDC, 800 mA

11

RW Series User Guide

Image 11

Contents UMAN-RWS-010 Rev. B May Contents Magnetic Stripe Reader Smart Card Reader Extending Battery Life General Cleaning InstructionsRW Series User Guide Product Improvements Proprietary StatementAgency Approvals and Regulatory Information Document Conventions RW 420 Overview RW 220 Overview Reporting Damage Introduction to the RW SeriesUnpacking and Inspection Getting Ready to Print Battery SafetyCharger Safety Installing the RW 420 Battery Charger Jack Installing RW Series BatteriesLI72 Charger LI72 ChargerLI72 Single Charger Types Indicator Charger Charger Status Function Short Circuit of Output Terminals Battery Contact ProblemGreen Solid Fully Charged ChargingAmber Power SupplyPower Indicator Model UCLI72-4 Quad ChargerCharging process per the following table Battery 80% Charged Hrs 25 Hrs Battery Fully ChargedMedia Support Loading Media ProcedureLoading the Media Media CompartmentMedia Roll Loading Media From An Internal SupplyBA16625-1 Loading Media From An External SupplyMedia Spacer Closing the Media Cover Control Panel Operator ControlsProgrammable LCD Settings Extended LCD Functions1 Display Functions Not Accessible from the Keypad1 Verify the Printer Is Working Printing a Configuration LabelUSB Port RS232/USB Port Connecting the PrinterCable Communications Serial RS232C and USB Combination PortRS232 Communications Cable Printer Communications Port CableCommunications Cable Bluetooth Networking Overview Wireless CommunicationsWireless Communications with Bluetooth Wireless Local Area Network Overview Setting Up the Software Radio Regulatory Information Bluetooth RW -ZBR3 Radio RW 220 and RWZebra Bluetooth Radio 2.0 RW-ZBR4 RW 220 and RW Compact Flash 802.11b Radio Module Europe EU Declaration of Conformity Zebra Value Radio, 802.11b Europe EU Declaration of Conformity Industry Canada IC Warning Wlan Module Using 802.11b/g Radio004 Europe EU Declaration of Conformity 주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다 Compact Flash 802.11b and Bluetooth Co-located Radio Modules RW Series User Guide Magnetic Stripe Reader Rdr indicates MSR is enabledCard Reader Options Magnetic Stripe Reader Slot Magnetic Stripe CardSmart Card Reader Clip printer to belt Printer can pivot freely Using the AccessoriesBelt Clip Using the Shoulder Strap Adjustable Shoulder StrapDisplay rotated Cradle Installing the RW 420 in the CradleCradles Normal Display CradleIndicator Charge Power IndicatorRemoving the RW 420 from the Cradle Refer to Figure RW 220 Vehicle CradleRemoving the RW 220 from the Cradle Extending Battery Life Preventive MaintenanceGeneral Cleaning Instructions Cleaning RW Series Printers LCD Control Panel Indicators TroubleshootingNo power Troubleshooting TopicsFlashing or icon Performing a Forced Shutdown Troubleshooting TechniquesCommunications Diagnostics Calling Technical Support Installed Installed softwareSettings for Wireless optionsConfiguration Label Example Configuration Label Example Memory/Communications Specifications SpecificationsPrinting Specifications RW 220 Media Specifications RW 420 Media SpecificationsCombination Port Communication PortsUSB Communications PortsUCC/EAN Font/Bar Code SpecificationsPhysical/Environmental/Electrical Specifications 94 mm max 81 mm Max 175 mm 160 mm 188 mm RW 420 Overall Dimensions94.1 mm1 81 mm1 # 6-32 x Mm deep Places 185.3 mm 111.8 mm 173.6 mm99.1 mm RW Series Accessories Part Number AK17463-008 RW Mod Plug to 9-Pin DB PC Cable Appendix aInterface Cables RS232 Download Cable USB Download CablePart Number AT17010-1 USB a to USB Mini B Cable More Interface Cables USB CableMedia Supplies Appendix BAppendix C Maintenance SuppliesEurope, Africa, the Middle East, and India contact Appendix DProduct Support Americas contactSerial Number Product ConfigurationProduct CodeProduct Disposal Battery DisposalAppendix E Select language Using zebra.comAppendix F Select printer model e.g. RWClick on Software & Utilities tab to download Label Vista Magnetic Stripe Reader 43 Smart Card Reader Index802.11b Compact Flash radio 34,?36 Bluetooth radio ZBR3 & QL+ZBR4201,255 B1 Patent Numbers