Zebra Technologies RW 420 Model UCLI72-4 Quad Charger, Power Supply, Amber, Green Charger Bay

Page 17

Model UCLI72-4 Quad Charger

The UCLI72-4 Quad Charger is designed to charge up to four RW Series battery packs simultaneously. Batteries must be removed from the printer to be charged in the Quad Charger.

1.Ensure that the charger has been installed properly per the Quad Charger instruction manual. Ensure that the power indicator on the front panel is on.

2.Remove any protective shrink-wrap and labels from all battery packs prior to use. Plug a battery pack into any one of the four charging bays as shown in Figure 6, not- ing the orientation of the battery pack. Slide the battery

pack into the charging bay until it stops. Then rock the battery pack back until it snaps into place. The amber in- dicator directly under the battery being charged will turn on if the battery is properly inserted.

The indicators under the battery will allow you to monitor

Figure 6: UCLI72-4 Quad Charger

Power Supply

1.Slide Battery Pack into Charger Bay

2. Rock Battery Pack into place

	Fast
	Charge	Full
	Fault	Full	Charge
	Fault		Charge

Ready

Amber

LED

	Fast
	Charge	Full
	Fault	Full	Charge
	Fault		Charge
			Ready

Fast Charge Fault

Full Charge

Ready

	Fast
	Charge	Full
	Fault	Full	Charge
	Fault		Charge
			Ready

Green	Charger Bay
LED

Power

Power Indicator

17

RW Series User Guide

Image 17

Contents UMAN-RWS-010 Rev. B May Contents Magnetic Stripe Reader Smart Card Reader Extending Battery Life General Cleaning InstructionsRW Series User Guide Product Improvements Proprietary StatementAgency Approvals and Regulatory Information Document Conventions RW 420 Overview RW 220 Overview Reporting Damage Introduction to the RW SeriesUnpacking and Inspection Getting Ready to Print Battery SafetyCharger Safety Installing the RW 420 Battery LI72 Charger Installing RW Series BatteriesLI72 Charger Charger JackLI72 Single Charger Types Indicator Charger Charger Status Function Green Solid Fully Charged Battery Contact ProblemCharging Short Circuit of Output TerminalsPower Indicator Power SupplyModel UCLI72-4 Quad Charger AmberCharging process per the following table Battery 80% Charged Hrs 25 Hrs Battery Fully ChargedLoading the Media Loading Media ProcedureMedia Compartment Media SupportMedia Roll Loading Media From An Internal SupplyBA16625-1 Loading Media From An External SupplyMedia Spacer Closing the Media Cover Control Panel Operator ControlsProgrammable LCD Settings Extended LCD Functions1 Display Functions Not Accessible from the Keypad1 Verify the Printer Is Working Printing a Configuration LabelCable Communications Connecting the PrinterSerial RS232C and USB Combination Port USB Port RS232/USB PortRS232 Communications Cable Printer Communications Port CableCommunications Cable Bluetooth Networking Overview Wireless CommunicationsWireless Communications with Bluetooth Wireless Local Area Network Overview Setting Up the Software Radio Regulatory Information Bluetooth RW -ZBR3 Radio RW 220 and RWZebra Bluetooth Radio 2.0 RW-ZBR4 RW 220 and RW Compact Flash 802.11b Radio Module Europe EU Declaration of Conformity Zebra Value Radio, 802.11b Europe EU Declaration of Conformity Industry Canada IC Warning Wlan Module Using 802.11b/g Radio004 Europe EU Declaration of Conformity 주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다 Compact Flash 802.11b and Bluetooth Co-located Radio Modules RW Series User Guide Magnetic Stripe Reader Rdr indicates MSR is enabledCard Reader Options Magnetic Stripe Reader Slot Magnetic Stripe CardSmart Card Reader Clip printer to belt Printer can pivot freely Using the AccessoriesBelt Clip Using the Shoulder Strap Adjustable Shoulder StrapCradles Installing the RW 420 in the CradleNormal Display Cradle Display rotated CradleIndicator Charge Power IndicatorRemoving the RW 420 from the Cradle Refer to Figure RW 220 Vehicle CradleRemoving the RW 220 from the Cradle Extending Battery Life Preventive MaintenanceGeneral Cleaning Instructions Cleaning RW Series Printers LCD Control Panel Indicators TroubleshootingNo power Troubleshooting TopicsFlashing or icon Performing a Forced Shutdown Troubleshooting TechniquesCommunications Diagnostics Calling Technical Support Settings for Installed softwareWireless options InstalledConfiguration Label Example Configuration Label Example Memory/Communications Specifications SpecificationsPrinting Specifications RW 220 Media Specifications RW 420 Media SpecificationsCombination Port Communication PortsUSB Communications PortsUCC/EAN Font/Bar Code SpecificationsPhysical/Environmental/Electrical Specifications 94 mm max 81 mm Max 175 mm 160 mm 188 mm RW 420 Overall Dimensions94.1 mm1 81 mm1 # 6-32 x Mm deep Places 185.3 mm 111.8 mm 173.6 mm99.1 mm RW Series Accessories Interface Cables RS232 Download Cable Appendix aUSB Download Cable Part Number AK17463-008 RW Mod Plug to 9-Pin DB PC CablePart Number AT17010-1 USB a to USB Mini B Cable More Interface Cables USB CableMedia Supplies Appendix BAppendix C Maintenance SuppliesProduct Support Appendix DAmericas contact Europe, Africa, the Middle East, and India contactProduct Product ConfigurationCode Serial NumberProduct Disposal Battery DisposalAppendix E Appendix F Using zebra.comSelect printer model e.g. RW Select languageClick on Software & Utilities tab to download Label Vista Magnetic Stripe Reader 43 Smart Card Reader Index802.11b Compact Flash radio 34,?36 Bluetooth radio ZBR3 & QL+ZBR4201,255 B1 Patent Numbers