Zebra Technologies RW 420, RW 220 manual Zebra Value Radio, 802.11b

Page 37

Zebra Value Radio, 802.11b

The following section only applies when the ZebraValue Radio, 802.11b (with FCC ID: I28MD-ZLAN11B) is installed in a RW series printer.The FCC ID number is on the serial number label on the back of the printer and canbe read with the module installed. Otherthan conditions specifiedelsewhere inthis manual, only oneoftheradiooptionscanbeinstalledintheprinteratonetimeandtheantennausedforthesetransmit- ters must not be co-located or must not operate in conjunction with any other antenna.

Caution • The radiated output power of this internal 802.11b radio is far below the FCC radio frequency exposure limits. Nevertheless, this radio must be used in such a manner that the antenna is 2.5 cm. or further from the human body. The radio and antenna are mounted internally in this printer such that when the printer is worn with the back of the printer against the body and the front of the printer (where paper exits) away from the body, then the 2.5 cm distance between the antenna and the users body will be met. Do not use the printer in an unauthorized manner.

European Regulatory Information for this Radio

AT	BE	CY	CZ	DK

EE	FI	FR	DE	GR

HU	IE	IT	LV	LT

LU	MT	NL	PL	PT

SK	SI	ES	SE	GB

Note: -Member states in the EU with restrictive use for this device are crossed out!

This device is also authorized for use in all EFTA member states (CH, IS, LI, NO)

Important Notice:

This device is a portable RF printer intended for commercial and industrial use in all EU and EFTA member states except in France where restrictive use applies.

37

RW Series User Guide

Image 37

Contents UMAN-RWS-010 Rev. B May Contents Magnetic Stripe Reader Smart Card Reader Extending Battery Life General Cleaning InstructionsRW Series User Guide Product Improvements Proprietary StatementAgency Approvals and Regulatory Information Document Conventions RW 420 Overview RW 220 Overview Unpacking and Inspection Introduction to the RW SeriesReporting Damage Charger Safety Battery SafetyGetting Ready to Print Installing the RW 420 Battery LI72 Charger Installing RW Series BatteriesLI72 Charger Charger JackLI72 Single Charger Types Indicator Charger Charger Status Function Green Solid Fully Charged Battery Contact ProblemCharging Short Circuit of Output TerminalsPower Indicator Power SupplyModel UCLI72-4 Quad Charger AmberCharging process per the following table Battery 80% Charged Hrs 25 Hrs Battery Fully ChargedLoading the Media Loading Media ProcedureMedia Compartment Media SupportMedia Roll Loading Media From An Internal SupplyMedia Spacer Loading Media From An External SupplyBA16625-1 Closing the Media Cover Control Panel Operator ControlsProgrammable LCD Settings Extended LCD Functions1 Display Functions Not Accessible from the Keypad1 Verify the Printer Is Working Printing a Configuration LabelCable Communications Connecting the PrinterSerial RS232C and USB Combination Port USB Port RS232/USB PortCommunications Cable Printer Communications Port CableRS232 Communications Cable Wireless Communications with Bluetooth Wireless CommunicationsBluetooth Networking Overview Wireless Local Area Network Overview Setting Up the Software Radio Regulatory Information Bluetooth RW -ZBR3 Radio RW 220 and RWZebra Bluetooth Radio 2.0 RW-ZBR4 RW 220 and RW Compact Flash 802.11b Radio Module Europe EU Declaration of Conformity Zebra Value Radio, 802.11b Europe EU Declaration of Conformity Industry Canada IC Warning Wlan Module Using 802.11b/g Radio004 Europe EU Declaration of Conformity 주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다 Compact Flash 802.11b and Bluetooth Co-located Radio Modules RW Series User Guide Card Reader Options Rdr indicates MSR is enabledMagnetic Stripe Reader Magnetic Stripe Reader Slot Magnetic Stripe CardSmart Card Reader Belt Clip Using the AccessoriesClip printer to belt Printer can pivot freely Using the Shoulder Strap Adjustable Shoulder StrapCradles Installing the RW 420 in the CradleNormal Display Cradle Display rotated CradleIndicator Charge Power IndicatorRemoving the RW 420 from the Cradle Refer to Figure RW 220 Vehicle CradleRemoving the RW 220 from the Cradle Extending Battery Life Preventive MaintenanceGeneral Cleaning Instructions Cleaning RW Series Printers LCD Control Panel Indicators TroubleshootingNo power Troubleshooting TopicsFlashing or icon Communications Diagnostics Troubleshooting TechniquesPerforming a Forced Shutdown Calling Technical Support Settings for Installed softwareWireless options InstalledConfiguration Label Example Configuration Label Example Printing Specifications SpecificationsMemory/Communications Specifications RW 220 Media Specifications RW 420 Media SpecificationsCombination Port Communication PortsUSB Communications PortsUCC/EAN Font/Bar Code SpecificationsPhysical/Environmental/Electrical Specifications 94 mm max 81 mm Max 175 mm 160 mm 188 mm RW 420 Overall Dimensions99.1 mm 185.3 mm 111.8 mm 173.6 mm94.1 mm1 81 mm1 # 6-32 x Mm deep Places RW Series Accessories Interface Cables RS232 Download Cable Appendix aUSB Download Cable Part Number AK17463-008 RW Mod Plug to 9-Pin DB PC CablePart Number AT17010-1 USB a to USB Mini B Cable More Interface Cables USB CableMedia Supplies Appendix BAppendix C Maintenance SuppliesProduct Support Appendix DAmericas contact Europe, Africa, the Middle East, and India contactProduct Product ConfigurationCode Serial NumberAppendix E Battery DisposalProduct Disposal Appendix F Using zebra.comSelect printer model e.g. RW Select languageClick on Software & Utilities tab to download Label Vista Magnetic Stripe Reader 43 Smart Card Reader Index802.11b Compact Flash radio 34,?36 Bluetooth radio ZBR3 & QL+ZBR4201,255 B1 Patent Numbers