Zebra Technologies PR4T manual Installing the P4T Series Battery Pack

Page 16

Installing the P4T Series Battery Pack

P4T/RP4T User Guide

Manual Introduction	RP4T Printers 35
pg.	pg.
4
P4T Overview- pg. 5	Maintenance pg. 36
Printer Preparation pg. 7	38	Troubleshooting pg.
Connecting the Printer pg. 27	43	Speci†cations pg.
Radio Regulatory Information pg. 31	Appendices pg. 46

Important • New battery packs are shipped uncharged. Remove any protective shrink- wrap and labels from a new battery pack prior to use.

Additional battery packs may be ordered using Zebra p/n AK18913-001.

If you are using an LI72 single charger or the LI72- 4 Quad Charger, you must charge the battery prior to installing it in the printer.

•.Insert the battery pack into the printer as shown in Figure 6 .

•Rock the battery pack into the printer as shown until it locks in place.

If you are using the AC adapter, you should allow the battery pack to charge completely prior to using it for the first time.

When a new battery pack is first installed, the Control Panel indicators may briefly turn on and then go off, indicating the battery is not fully charged. Refer to the Charging the Battery and Operator Controls topics in this manual.

Figure 6: Installing the P4T Series Battery Pack

Charger port for use

with the P1026943-1 AC Adapter

Insert this side of the battery pack into the bottom of the printer as shown.

Rock the battery pack until it clicks into place.

Index pg. 52

P4T Series Battery Pack

Section Continues

6

Image 16

Contents Manual Introduction RP4T Printers Printer Preparation pgIndex pg UMAN-P4T-013 Rev.AProprietary Statement Document Conventions Introduction to the P4T Series Unpacking and InspectionReporting Damage RP4T Printers 35 Manual IntroductionP4T/RP4T Overview Printer Preparation pg Troubleshooting pgUSB Port P4T Series Technology Radio Regulatory Information pg Appendices pg Index pgDirect Thermal Thermal TransferCharger Safety Battery SafetyPrinter Preparation Single Battery Charger Approved ChargersUnauthorized equipment LI72 Charger AT17696-xxBattery Charging Receptacle P4T Series Battery Pack LI72 Battery ChargerConnecting Printer Speci†cations IndexMaintenance pg P4T Series BatteryLED Status Charger Status Input VoltageProtective cover For access to Charger Receptacle Varies withLocation P4T Series AC AdapterDC Power Cord open wires P4T Series DC AdapterP4T Vehicle Cradle DC Adapter Access the charger receptacle located on the bottomVehicle cradle as Indicated Installation Guidelines DC Adapter You to monitor the charging process per Indicators under each battery will allowTable below Installing the P4T Series Battery Pack Installing the P4T Series Battery PackLoad the Media Loading Media From An External Supply Media Spacer Rear Feed Slot External Media SourceClose the Media Cover Printer pgAdjusting The Media Support Disks Close the Printer Covers Past the printheadCover Close the media cover and ensure it latches in placeOperator Controls Printer ControlsTion for more information on the printer status icons Programmable LCD Settings Function Default setting Scroll & Select OptionsWlan ID Adjustable Shoulder Strap Snap into feature on printerHold Buckle To lengthen Pull Strap hereVerify the Printer Is Working Before you connect the printer to your computer orPortable data terminal, make sure that the printer is Proper working order. You can do this by printing a conConnecting the Printer Cable CommunicationsConnector Connector ConnectorConnector DetailsConnect the Printer by Radio Communications with your printerSetting Up the Software Wireless CommunicationsBluetooth Networking Overview Radio Regulatory Information Bluetooth ZBR4 RadioEuropean Regulatory Information for this Radio NCC Taiwan Compliance Statement Europe EU Declaration of Conformity802.11b/g and Bluetooth Co-located Radio Modules Rfid option Printer ModelDigit Con†gurationModel RP4T Rfid Encoder Generation 2 Class 1 UHF Passive Tags Supported By The P4TExtending Battery Life Preventive MaintenanceGeneral Cleaning Instructions P4T Series Cleaning MechanismTroubleshooting Topics TroubleshootingIcon Status Indication Ref. to Troubleshooting Topic Troubleshooting Topics Poor or faded print or low battery icon «ashingTo enter Communications Diagnostics Mode Troubleshooting TechniquesTo terminate the Communications Diagnostics Mode Bluetooth radio First diagnostic report for all P4T Series printersSecond diagnostic report for a printer with an Second diagnostic report End of second diagnostic reportSpecifications Printing Speci†cationsMemory/Communications Speci†cations Communications PortsRegulatory pg Index pg Radio Information AppendicesRotation Angles Fonts Available Physical/Environmental/Electrical Speci†cations 220,5 mm 57 in ,5mm80,2 mm External Media Supply Loading SlotManual Introduction RP4T Printers P4T pg Maintenance Part Number AK18666-1 RW Mod Plug to USB a CableAppendix B Appendix C Maintenance SuppliesMedia Supplies Appendix D Product SupportAmericas, contact Asia Paci†c region, contactAppendix E Appendix F Select manual type Click on SubmitAppendix G- Patents Index Zebra Technologies Corporation UMAN-P4T-013 Rev. a May