Zebra Technologies PR4T manual Approved Chargers, Single Battery Charger, Unauthorized equipment

Page 8

P4T/RP4T User Guide

Manual Introduction	RP4TPrinters 35	Approved Chargers
Manual Introduction	RP4TPrinters 35		Use of chargers not approved by Zebra specifically for use with the P4T Series will void the warranty and could cause damage
		The following table lists battery chargers approved for use with the P4T Series Printer.
pg.	pg.		to the printer or the battery pack. Zebra is not responsible for any damage to equipment caused by the improper use of
4			unauthorized equipment.
			unauthorized equipment.

P4T Overview- pg. 5	Maintenance pg. 36
PrinterPreparation pg. 7	Troubleshooting 38

Description

LI72 single charger)

AC Adapter/US Line Cord

AC Adapter/UK Line Cord

AC Adapter/EU Line Cord

UCLI72-4 Quad Charger

Part no

AT17696-xx1AT18737-xx

AK18913-002

AK18913-006

AK18913-007

AC18177-xx1

Notes.

Must be used with battery removed from printer

Must be used with battery installed in printer

Must be used with battery installed in printer

Must be used with battery installed in printer

Must be used with battery removed from printer

Description	Part no	Notes.
15-60V DC
15-60V DC
Adapter/Right	AK18913-003	N/A
Angle

1.Full part number is determined by the AC main adapter appropriate for the region of intended use. Consult your Zebra sales represenetative or the factory for the appropriate part number.

pg.

Single Battery Charger

Figure 2: LI72 Single Charger

The LI72 Charger

LI72 charger is a wall mounted fast charger with a universal 110 to 230, 50-60 Hz. VAC input. Multiple AC plug configurations comply

Connecting the Printer pg. 27	Speci†cations pg. 43
Radio Regulatory Information pg. 31	Appendices pg. 46
	Index pg. 52

Yellow Green

LI72 Charger

AT17696-xx

with most international standards. This charger is intended for use with the P4T Series printers which are equipped with Lithium Ion (Li-ion) batteries.

Full part numbers are determined by the AC mains connectors. Consult Zebra or your authorized re-seller for full part number in- formation.

The LI72 will charge a battery pack as fast as its charge level will allow, and then switch over to a maintenance charge to keep the charge at its maximum.

Section Continues

Image 8

Contents Manual Introduction RP4T Printers Printer Preparation pgIndex pg UMAN-P4T-013 Rev.AProprietary Statement Document Conventions Introduction to the P4T Series Unpacking and InspectionReporting Damage RP4T Printers 35 Manual IntroductionUSB Port Printer Preparation pg Troubleshooting pgP4T/RP4T Overview P4T Series Technology Radio Regulatory Information pg Appendices pg Index pgDirect Thermal Thermal TransferPrinter Preparation Battery SafetyCharger Safety Single Battery Charger Approved ChargersUnauthorized equipment LI72 Charger AT17696-xxBattery Charging Receptacle P4T Series Battery Pack LI72 Battery ChargerConnecting Printer Speci†cations IndexMaintenance pg P4T Series BatteryLED Status Charger Status Input VoltageProtective cover For access to Charger Receptacle Varies withLocation P4T Series AC AdapterDC Power Cord open wires P4T Series DC AdapterVehicle cradle as Indicated Access the charger receptacle located on the bottomP4T Vehicle Cradle DC Adapter Installation Guidelines DC Adapter Table below Indicators under each battery will allowYou to monitor the charging process per Installing the P4T Series Battery Pack Installing the P4T Series Battery PackLoad the Media Loading Media From An External Supply Media Spacer Rear Feed Slot External Media SourceClose the Media Cover Printer pgAdjusting The Media Support Disks Close the Printer Covers Past the printheadCover Close the media cover and ensure it latches in placeTion for more information on the printer status icons Printer ControlsOperator Controls Programmable LCD Settings Function Default setting Scroll & Select OptionsWlan ID Adjustable Shoulder Strap Snap into feature on printerHold Buckle To lengthen Pull Strap hereVerify the Printer Is Working Before you connect the printer to your computer orPortable data terminal, make sure that the printer is Proper working order. You can do this by printing a conConnecting the Printer Cable CommunicationsConnector Connector ConnectorConnector DetailsConnect the Printer by Radio Communications with your printerBluetooth Networking Overview Wireless CommunicationsSetting Up the Software European Regulatory Information for this Radio Bluetooth ZBR4 RadioRadio Regulatory Information NCC Taiwan Compliance Statement Europe EU Declaration of Conformity802.11b/g and Bluetooth Co-located Radio Modules Rfid option Printer ModelDigit Con†gurationModel RP4T Rfid Encoder Generation 2 Class 1 UHF Passive Tags Supported By The P4TGeneral Cleaning Instructions Preventive MaintenanceExtending Battery Life P4T Series Cleaning MechanismIcon Status Indication Ref. to Troubleshooting Topic TroubleshootingTroubleshooting Topics Troubleshooting Topics Poor or faded print or low battery icon «ashingTo terminate the Communications Diagnostics Mode Troubleshooting TechniquesTo enter Communications Diagnostics Mode Second diagnostic report for a printer with an First diagnostic report for all P4T Series printersBluetooth radio Second diagnostic report End of second diagnostic reportSpecifications Printing Speci†cationsMemory/Communications Speci†cations Communications PortsRotation Angles Fonts Available Radio Information AppendicesRegulatory pg Index pg Physical/Environmental/Electrical Speci†cations 220,5 mm 57 in ,5mm80,2 mm External Media Supply Loading SlotManual Introduction RP4T Printers P4T pg Maintenance Part Number AK18666-1 RW Mod Plug to USB a CableMedia Supplies Maintenance SuppliesAppendix B Appendix C Appendix D Product SupportAmericas, contact Asia Paci†c region, contactAppendix E Appendix F Select manual type Click on SubmitAppendix G- Patents Index Zebra Technologies Corporation UMAN-P4T-013 Rev. a May